Installation Instructions - Altronix HubWayEX16 Installation Manual

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes
and authorities having jurisdiction . Wiring should be UL Listed and/or Recognized wire suitable for the application .
1 . Set the input voltage selector switch located on the left side of the HubWayEX16/EX32 unit (facing front
panel) for 115VAC or 230VAC operation (Fig. 1b, pg. 5) .
2 . Attach mounting brackets to HubWayEX16/EX32 unit for rack or wall mount installation (Figs. 6-7, pg. 8) .
Affix rubber pads to HubWayEX16/EX32 for shelf installation (Fig. 8, pg. 8) .
3 . Secure the unit in a rack, mount unit to a wall or place unit on a shelf as desired (unit should be spaced at
least 3" from any video monitors) .
4 . Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 5, pg. 8) .
5 . Plug the grounded AC line cord into the IEC 320 connector of the HubWayEX16/EX32 .
For US & Canada the plug end is a 3 prong type B plug used for standard 115VAC receptacles, as provided
with unit (Fig. 1g, pg. 5) . For non North American 230VAC applications use the appropriate 3 prong plug
that matches the local standard receptacle .
6 . Connect the BNC video outputs for HubWayEX16/EX32 Channels 1-32 to the corresponding video inputs
on the head end equipment (DVR) (Fig. 1c, pg. 5) .
7 . Connect the RS422/RS485 output of the head end equipment (DVR) to the one (1) or both data input
terminal blocks of the HubWayEX16/EX32 unit (polarity must be observed) (Fig. 1f, pg. 5) .
Note: The Data input terminals of the HubWayEX16/EX32 must be wired in parallel for proper operation .
When using fixed cameras disregard this step .
8 . Connect one (1) end of a CAT-5 or higher structured cable into the RJ45 jack marked [CH 1-4, CH 5-8,
CH 9-12, CH 13-16] of the HubWayEX16 or [CH 1-4, CH 5-8, CH 9-12, CH 13-16, CH 17-20, CH 21-24,
CH 25-28, CH 29-32] of the HubWayEX32 (Fig. 1d, pg. 5) . Connect the opposite end of the CAT-5 or
higher structured cable into the corresponding RJ45 jack marked [CH 1-4, CH 5-8] HubWayEXP
(Fig. 4, pg. 7) or [VIDEO 1-4] of the HubSat4D/Di (Fig. 5, pg. 8) .
9 . Connect one (1) end of a CAT-5 or higher structured cable into the RJ45 jack marked [DATA] of the
HubWayEX16/EX32 (Fig. 1e, pg. 5) . Connect the opposite end of the CAT-5 or higher structured cable
into the RJ45 jack marked [DATA] of HubWayEXP (Fig. 4, pg. 7) or [DATA 1-4] of the HubSat4D/Di
(Fig. 5, pg. 8) .
Note: When using fixed cameras disregard this step .
Repeat steps 8 and 9 for cameras 5-8, 9-12, 13-16, 17-20, 21-24, 25-28, 29-32 .
(refer to HubSat4D/Di or HubWayEXP installation instructions for camera hookups) .
10 . Upon completion of wiring set illuminated master power disconnect circuit breaker to the RESET (ON)
position (Fig. 6, pg. 11).
11 . The video signal indicator LEDs (Red) located on the front of the HubWayEX16/EX32 will illuminate when
video signal is present (Fig. 1a, pg. 5). If any of these LEDs are not illuminated, there is no video signal
for that corresponding channel .
- 4 -

Installation Instructions:

HubWayEX16/EX32