Advertisement
Connection
Precautions
Connecting Power Source
•
Be sure to switch off the unit before
Connect power, using one of the methods
installation and connection.
listed below:
•
The installation should be made by
To use the power adapter
qualified service personnel or system
Connect DC 12 V or AC 24 V power source to
installers.
the power input terminal as shown below.
•
Do not expose the power and
(recommended power adapter is DC 12 V or
connection cables to moisture, which
AC 24 V/1.5 A or above)
may cause damage to the unit.
Connecting Network
You can control and monitor the system
via network. With the remote control
(monitoring), you can change the system
configuration or monitor the image via
network. After the installation, check the
network settings for the remote control and
To use the PoE (Power over Ethernet)
monitoring work.
device
ETHERNET
Connect the IP camera to your network using
With PoE
Connect the PoE cable to the LAN port on the
a standard RJ-45 network cable as shown
unit. You must use the "IEEE802.3af" standard
below.
PoE device.
ETHERNET
With PoE
ETHERNET
With PoE
PoE Device
(IEEE802.3af )
Broadband
Service
PoE Device
(IEEE802.3af )
Router
Broadband
Service
NOTE:
If the camera doesn't work properly after
connecting PoE device, please check if the
PoE device supplies enough power.
Installation
Follow the instructions below to ceiling or
2.
Connect the cables to the cable jacks of
wall mount the camera.
the camera body.
Mounting the Camera
1.
Using a template as a guide, make a hole
through the ceiling.
Connecting Alarm Device
Connecting Microphone
and Speaker Device
Alarm terminals are used to connect the
alarm (relay) devices such as sensors, door
Optionally connect an active speaker and/or
switches, etc.
external microphone with a built-in amplifier.
ALARM IN&OUT / ALARM IN&OUT RETURN
(Sensor Input/ Relay Output)
Connect the sensor device and alarm (relay)
AUDIO OUT
device to the alarm terminal. Alarm signal is
outputted at an event occurrence.
AUDIO IN
Alarm (relay)
Device
NOTE:
Sensor Device
Keep the microphone away from the speaker
to avoid howling.
NOTE:
The Photo MOS Relay is rated for 100 mA at
20 V DC or 100 mA at 28 V AC.
Connecting Waterproof
3.
Install the camera by using M3 Tapping
screws to fix it on the ceiling.
processing of cable
Surely use the Butyl tape.
1.
Connect the cables.
2.
Bind the cables together with Butyl tape.
WARNING:
•
The cables are not waterproofed
completely. So seal the tube ends and
the portions between cable cores as well
as connecting portions with Butyl tape.
•
If not using the Butyl tape, it may cause
water absorption from a gap and finally
condensation and water leakage.
Using the micro SD card
NOTES:
•
Do not use the power too much when
You can record your surveillance environment
you insert the micro SD card. The micro
with the micro SD card even if the network is
SD card may be damaged.
disconnected condition.
•
If you insert the micro SD card in the
To insert the micro SD card
wrong position, the micro SD card
1.
Disassemble the Cover from the main
may be damaged or it may cause the
body by turnining it counterclockwise.
malfunction of the micro SD Card Slot.
•
Keep the terminal part of the micro SD
card in clean. Be careful the terminal part
WIDE
of the micro SD card not to dusty.
•
As the micro SD card is consumable, the
micro SD card end its days and may be
not able to save data if you use it more
than over certain times. In this case,
TELE
replace micro SD card to buy a new one.
2.
Insert the micro SD card carefully as
shown in the following illustrations.
Make sure the micro SD card terminal
position before insert the micro SD card.
Push the back end of the micro SD card
to fix it at the last step.
WIDE
Adjust the Focus
3.
Set the zoom level of the lens.
You should adjust the focus as shown below
WIDE
steps.
1.
Disassemble the Cover from the main
body by turnining it counterclockwise.
TELE
WIDE
4.
Set the focus of the lens correctly.
TELE
WIDE
NEAR
2.
Connect the portable monitor to the
video jack using the test monitor cable.
TELE
FAR
5.
Close and tighten the Cover to the main
body by turning it clockwise.
Test Monitor
Cable
Remove the micro SD card
CAUTION:
•
1.
Press the back end of the micro SD card
to release the lock condition.
NEAR
•
FAR
Recommended the micro SD card
specification
Maker
LG
Sandisk
2.
Take the micro SD card out carefully from
the camera. It may cause a malfunction
Transcend
of the micro SD card or the micro SD
card slot if you use the power too much
NOTE:
at lock status.
Speed of reading and writing more than
10 MB/Sec. (Class 6)
NEAR
TELE
FAR
Adjust the camera
Assemble the Sunshield
position
Adjust the position of the Sunshield, then
NEAR
assemble the Sunshield.
You should adjust the camera angle position
as shown below illustration. Adjust the
camera angle position by following step a
and b.
FAR
NEAR
1.
Adjust the Pan.
FAR
2.
Adjust the Tilt.
3.
Adjust the Angle.
If you install the micro SD card on the
camera and remove with the micro SD
card condition indicator lights on, you
must unmount the micro SD card by
using the [SD Card > Configuration >
Disk Management > Unmount] menu.
The micro SD card data is compromised
or the camera may not operate normally,
if you remove the card without use
[Unmount] function.
LG Electronics is not responsible for
deleted data caused by user mishandling
when you insert or remove the micro
SD card.
Block Size
Capacity
(FAT 32)
Less than
32 kbyte
32 GB
Advertisement
