LG LNU5100R series Owner's Manual

OWNER'S MANUAL
High Definition Network
Camera
Please read this manual carefully before operating
your set and retain it for future reference.
MODEL
LNU5100R series
Specification
Item LNU5100R series
Image Device 6.08 mm (1/3 type) Progressive Scan CMOS
(1.3 Mega Pixels)
Lens Type 2.8 mm to 10 mm F1.2
Day/Night ICR
Minimum Color 0.3 lx (F1.2, Gain : High)
Illumination
B/W 0 lx (LED On)
IR Distance 30 m
WDR Support
Image Enhancement Backlight Compensation, 2D+3D-DNR, Exposure
Control, Sens Up Control, AGC, White Balance,
Privacy Masking, EIS, Sharpness, Digital Zoom,
Scene mode
Resolution (Maximum) Up to 1 280 x 1 024
Output RJ-45 (Network), RCA (Installation)
Frame Rate (Maximum) 30 fps @ 1280 x 1024, 30 fps @ 720p
Compression H.264_HIGH, H.264, MJPEG
Multi-Streaming Dynamic Profile (Up to 7)
Audio In/Out 1/1
Audio Compression G.711, G.726
2-way Audio Support
SD Slot microSD
EVENT Alarm In/Out 1/1
Motion detection Support
Event Notification Relay Out, Email, FTP
Pre Event Buffering Support
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated dangerous voltage
within the product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.
WARNING: This product contains chemicals known to the State of California to cause cancer and
birth defects or other reproductive harm. Wash hands after handling.
FCC WARNING: This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause harmful interference unless the modifications are
expressly approved in the instruction manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is made.
REGULATORY INFORMATION: FCC Part 15
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
• A suitable conduit entries, knock-outs or glands shall be provided in the cable entries of this
product in the end user.
• Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the same or
equivalent type recommended by the manufacturer. Dispose of used batteries according to
the manufacturer's instructions.
• Holes in metal, through which insulated wires pass, shall have smooth well rounded surfaces
or shall be provided with brushings.
This Class A digital apparatus complies with Canadian ICES-003.
AB28
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
VA Intelligent Motion Support
Detection
Streaming Support
Metadata
Trip Zone Support
Object Counting Support
Integrated Client LVi510
Remote S/W LVi510, Mobile application (iPhone, Android, iPad)
Connections Up to 10
Protection IP66, Vandal proof
Security Password Protection, HTTPS(SSL, TLS)
Ethernet 10/100 Ethernet
IPv4 and IPv6 TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP
Protocol
IPv4 FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS(LG)
Open Protocol ONVIF 2.2 Profile S,PSIA 1.1
Operation Temperature/Humidity -10 ºC to 50 ºC / 0 % RH to 80 % RH
Power Source PoE (IEEE 802.3af ), DC 12 V (±20 %),
AC 24 V ( ±10% )
Power Consumption 9.9 W
Input current AC 24 V Maximum 590 mA
DC 12 V Maximum 690 mA
PoE Maximum 190 mA
Dimension (W x H x D) 84 mm x 83.5 mm x 339 mm
Weight 1.4 kg (with Sunshield 1.57 kg)
Warning: Do not install this equipment in a
LG Electronics hereby declares
confined space such as a bookcase or similar
that this/these product(s) is/are
unit.
in compliance with the essential
Warning: Wiring methods shall be in requirements and other relevant
accordance with the National Electric Code, provisions of Directive 2004/108/
ANSI/NFPA 70. EC and 2011/65/EU.
Warning: This is a class A product. In a Contact office for compliance of this
domestic environment this product may cause product:
radio interference in which case the user may
LG Electronics Inc.
be required to take adequate measures.
EU Representative, Krijgsman 1,1186 DM
Warning: To reduce a risk of fire or electric Amstelveen, The Netherlands
shock, do not expose this product to rain or
Disposal of your old appliance
moisture.
Caution: This installation shall be made by a
1. When this crossed-out
qualified service person and shall conform to wheeled bin symbol is
all local codes. attached to a product
it means the product is
Caution: To avoid electrical shock, do not
covered by the European
open the cabinet. Refer servicing to qualified
Directive 2002/96/EC.
personnel only.
Caution: The apparatus shall not be exposed 2. All electrical and electronic products
to water (dripping or splashing) and no objects should be disposed of separately
filled with liquids, such as vases, shall be
from the municipal waste stream
placed on the apparatus. via designated collection facilities
appointed by the government or the
Note:
local authorities.
Please make sure the product is installed
3. The correct disposal of your old
appropriate places where secured from flood,
appliance will help prevent potential
such as under the eaves, to operate properly.
negative consequences for the
This product is certified as IP66 standard.
environment and human health.
However, if there is any flood concerns, it
4. For more detailed information about
is highly recommended to use an outdoor
disposal of your old appliance, please
Housing. When you install the camera inside
contact your city office, waste disposal
an outdoor Housing, please use one of the
service or the shop where you
following methods:
purchased the product.
1. Remove the front glass of Housing before
EEE Compliance with Directive.
installing the camera.
(for Turkey only)
2. To keep the front glass of Housing,
remove the front cover, and then put the
Important Safety
camera close to the front glass.
Instructions
To disconnect power from mains, pull
out the mains cord plug. When installing
1. Read these instructions.
the product, ensure that the plug is easily
2. Keep these instructions.
accessible.
3. Heed all warnings.
Part Names and Functions
a b c d e
i j k l m
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings.
Install in accordance with the
Handling of the unit
manufacturer's instructions.
8. Do not install near any heat sources such
Be careful not to spill water or other liquids on
as radiators, heat registers, stoves, or other
the unit. Be cautious not to get combustible or
apparatus (including amplifiers) that
metallic material inside the body. If used with
produce heat.
foreign matter inside, the camera is liable to
9. Do not defeat the safety purpose of
fail or to get cause of fire or electric shock.
the polarized or grounding-type plug.
•
A polarized plug has two blades with
one wider than the other. A grounding
•
type plug has two blades and a third
grounding prong. The wide blade or the
third prong are provided for your safety.
If the provided plug does not fit into
your outlet, consult an electrician for
•
replacement of the obsolete outlet.
10. Protect the power cord from being
walked on or pinched particularly at
plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments/accessories
Operating and storage
specified by the manufacturer.
12. Use only with the cart, stand, tripod,
location
bracket, or table specified by the
manufacturer, or sold with the apparatus.
Avoid viewing a very bright object (such as
When a cart is used, use caution when
light fittings) during an extended period. Avoid
moving the cart/apparatus combination
operating or storing the unit in the following
to avoid injury from tip-over.
locations.
•
•
13. Unplug this apparatus during lightning
•
storms or when unused for long periods
•
of time.
•
14. Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
f g h a Lens Cover
b Angle adjuster
Adjust the camera angle.
c Tilt adjuster
Adjust the tilt position.
d Power input terminal
Connects to DC 12 V or AC 24 V power supply using proper cables. This camera must
always be operated DC 12 V or AC 24 V. Certified/Listed Adaptor which comply with LPS.
e AUDIO IN / OUT (Line Level Input/ Output)
f ALARM IN&OUT / ALARM IN&OUT RETURN
Provides physical interface for sensor and Alarm/Relay.
g ETHERNET/PoE Port
Connects to a PC or a network via a hub with a 10 BASE-T/100 BASE-TX cable attached
RJ-45 connector.
NOTE:
Power over Ethernet (PoE) is a technology that integrates power into a standard LAN
infrastructure. It enables power to be provided to the network device, such as a network
camera, using the same cable as that used for network connection. It eliminates the need
for power outlets at the device locations and enables easier application of uninterruptible
power supplies (LPS).
h Pan adjuster
Adjust the pan position.
i IR Sensor
j IR LED
k Video Out connector
Use this jack for checking the picture with portable monitor when install the camera.
l micro SD card slot
Insert the micro SD card.
m RESET button
Push the button more than 3 seconds, this would restore the factory default network
related settings.
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
Remove dust or dirt on the surface of the
lens with a blower.
Use a dry soft cloth to clean the body. If it
is very dirty, use a cloth dampened with a
small quantity of neutral detergent then
wipe dry.
Avoid the use of volatile solvents such
as thinners, alcohol, benzene and
insecticides.
They may damage the surface finish and/
or impair the operation of the camera.
Extremely hot or cold places (operating
temperature -10 °C to 50 °C, however, we
recommend that the unit be used within
a temperature range of 0 °C to 45 °C)
Damp or dust place
Places exposed to rain
Places subject to strong vibration
Close to generators of powerful
electromagnetic radiation such as radio
or TV transmitters.