Kontron CP6011 Quick Reference

CP6011 CP6011
CP6011
... always a Jump ahead!
6U cPCI Single Processor
CPCI Pentium-M Dual PMC
QUICK REFERENCE
Board Rev.
1
Document version 1.3

CONNECTORS

CONNECTORS
CONNECTORS
J1-J5 CompactPCI J14 IDE Mezzanine
Post Code 64-bit PCIX Mezzanine & PIM
J6 JN1A-JN4A
Memory SODIMM 1-2 64-bit PCIX Mezzanine
J7-J8 JN1B-JN3B
J9

Ethernet Management

SW1 Reset Button (faceplate)
COM1 (faceplate) (RJ-45) Battery
J10 BT1
USB (faceplate)

LEDs

J11 LP1
J12 Compact Flash J16 JTAG
Hot Swap Switch
J13
JUMPER SETTINGS ( Default Setting)
JUMPER SETTINGS ( Default Setting)
W1 (1-2), W1 (3-4) W6, W7, W8

PMC A VIO Settings

Backplane PCI Maximum Speed
W1(1-2) W1(3-4)
3.3V VIO out in PCI 33MHz
5V VIO in out PCI 66MHz
PCIX 66MHz
W1 (5-6) User Jumper
PCIX 100MHz
PCIX 133MHz
Low in
Bridge Disabled
High out
Brisge Dis. In I/O Slot
W2(1-2) Console Redirection
W9 Onboard IPMI
in
Enabled
Disable
out
Disabled
Enable
W2(3-4) Reserved
W10 CompactFlash
out
Master
W2 (5-6) Onboard Video Slave
Disabled in
W11, W12
Enabled out

PMC B VIO Settings

W3 Reserved
3.3V VIO
out
5V VIO
W4, W5 COM2 Terminations
W13 Clear CMOS
RS-422/485 modes only W4 W5
Clear CMOS
With termination in
in
Normal
Without termination out out

First Level Debugging

Blue LED always ON Blue LED OFF
1. Check the jumper settings
1. Remove all peripheral and external connections.
2. Verify if the board is in the correct CPCI slot. 2. Check the memory
3. Verify PMC VIO jumpers 3. Check post code on
4. Verify the power supply. Blue/User led.
Warning:
Both red LEDs always ON
Be sure you have the right
1. Check PMC VIO jumpers
backplane VIO setting
according to the board
configuration.
AMBER: Activity
Lights ON
while transferring
Green : Link
Lights ON when
the link is established
Note : LED colors
may change
8
W6 W7 W8
in in in
1
out
in in
BLUE / USER LED
in out in
out out
in

USER LED

out out out
in out out 8
in
in out
1
in
out
1
in
out
W11 W12
in out
out in
in
out
PMC A
J9
ETHERNET MANAGEMENT
LP1

RESET BUTTON

SW1
COM1
J10
USB
J11
4
PMC B
CP6011
WARNING
Make sure that only W1(1-2) or
W1(3-4) is set. Only one at the time
must be installed.
J6
1 4
B

J7

J8

A
JN4A is routed to J4 for the
PIM adapter, using 32
differential pairs
Lithium
3.6V
MCH
E7501
BT1
Rage
Mobility M
ICH3-S
J12
PCI6540
P64H2
1
2 4 6 8 10 2 4 6 8 10 12 14
2 2 2 2 2 2 2 2 2 2
J13
1 3 5 7 9 11 13 1 1 1 1 1 1 1 1 1 1
1 3 5 7 9
J16 W3
2 2 2 2 2 2 2 2 2 2
WARNING
Make sure that only W11 or W12 is
1 1 1 1 1 1 1 1 1 1
set. Only one at the time must be
installed.
E D C B A
22
J5
1
1
25
15
J4
11
2 4 6
2 4 6
W2 1 3 5 W1
1 3 5
1
1
19 E D C B A
J3
Pentium
M
1 1
22
J2
1
1
25
J1
15
11
63
64
1 1 1
J14
E D C B A