Description; Features Of Kds-100; Mechanical Specifications - Kenwood TK-2180 Modification Information

2 CONNECT OPTIONAL DEVICES
2.3 KDS-100
(TK-7180/ 8180 only)
You can connect the data terminal (KDS-100) to the TK-
7180/ 8180 transceivers to make data communications.
This section describes how to connect the KDS-100 to
the TK-7180/ 8180 transceivers.

2.3.1 Description

This transceiver can be configured to work with a data
terminal used to perform data transmission. This
transceiver is equipped with serial input/ output and data
modulation input/ output terminals. FleetSync compatible
mobile transceivers,Kenwood TK-7100/ 8100/ 780/ 880/
7150/ 8150/7180/ 8180/ x60G series or etc, support the
KDS-100.
Also, this KDS-100 is equipped with DSP (Digital Signal
Processing), general purpose serial ports, and general
purpose I/O ports. Thus, it has been designed to work
with various peripheral devices. Although we provide the
FPU (programming software KPG-71D).

2.3.2 Features of KDS-100

• Full-dot display (240 x 64 dots) with backlight function
• A dealer programmable PF keys (Programmable
Function Key) with backlight function
• The following external terminals are available.
- Serial communication terminal
- I/ O control terminal
- Data modulation I/ O terminals
• The following internal terminals are available.
- Two general purpose serial ports (compatible with
the RS-232C signal level)
- PC/ AT keyboard input terminal (ask R&D )
- NMEA0183 GPS receiver connection terminal
- Input terminal for differential GPS signal to transfer
to the GPS equipment.
- Two clock synchronizer serial input terminals (for
low-cost card reader) (ask R&D)
- General purpose I/O control terminals
• DSP for supporting high speed data communication
• Real time clock
• Battery status memory for data communication
• Tri-color LED indicating the communication port status
• Modem output level adjustment function using the
command generated from the electronic volume (PC
& Panel Tune)
• Firmware update function using a flash ROM
• This transceiver supports the following protocols.
12
- Fleet-Sync protocol capable (Non-FleetSync
capable LTR/ Conventional transceivers can be yet
interfaced with FleetSync compatible MDT to work.
i.e.TK-*60G)
- FleetSync serial protocol 1 (for full FleetSync PC
protocol 1 compatible transceiver. i.e. TK-780/880)
- FleetSync serial protocol 2 (for full FleetSync PC
protocol 2 compatible transceiver. i.e. TK-7180/
8180)
• Internal alarm to notify the message reception
• Advanced message function utilizing the FleetSync
Short/ Long Message
• PTT ID Display
• GPS Auto/Polling capability (Install GPS unit into the
KDS-100 or Transciver)
• Radio Remote (For PC2 Protocol compatible Radio)
• PTT ID Display and Log backup
• Emergency Feature Capability (For PC2 protocol)

2.3.3 Mechanical Specifications

!
Product Dimensions and Weight
Table 2-8 Product Dimensions and Weight
Item
Width
Depth
Height
Weight
A: Dimension without projections
B: Dimension including projections
!
Front Panel
• Key Layout: 9-key top set with rubber having LED
backlight
• Display: 240 x 64 positive type full-dot matrix LCD
with LED backlight
• LED: Tri-color LED
• Pigtail connection cable (15-pin Molex)
!
Rear Panel
• Screw hole for mobile bracket (4 mm screw)
• Connector for external devices
Modification Information
Body
A B
187 mm 187 mm
42 mm 46.5 mm
88 mm 88 mm
0.50 kg
Version: 1.13 USA