Page 2
Version Change History Date Version Description Remark 2017/10/06 1.0 First release Cosa 2018/7/3 Modify VESA information Cosa WMP-24C/24F User’s manual...
Page 3
Intel is a trademark or registered trademark of Intel Corporation. Microsoft Windows is a registered trademark of Microsoft Corporation. Winbond is a registered trademark of Winbond Electronics Corporation. All other product names or trademarks are properties of their respective owners. WMP-24C/24F User’s manual...
Page 4
To avoid risk of electric shock, this equipment must only be connected to a supply mains with protective earth. Do not modify this equipment without authorization of the manufacturer. WMP-24C/24F User’s manual...
Safety Instructions Intended use The WMP-24C/24F is intended to serve as a medical monitor which is designed for general purpose for hospital environment and for diagnosis. It could be used for Surgical, Radiology, PACS (Picture Archiving Communication Systems), LIS (Lab Information Systems) and Electronic Medical Record purpose.
Page 6
Do not overload the AC outlets or extension cords. Electrical shocks or fires may occur from overloading. Do not touch the power source during a thunderstorm. If your hands are wet, do not touch the plug. WMP-24C/24F User’s manual...
Page 7
Then contact a service technician for repairs. Ventilation Spacing Do not cover or block the openings on the top and back sides of the display unit. Inadequate ventilation may cause overheating thus reducing the lifespan of the unit. WMP-24C/24F User’s manual...
Page 8
Please use a dry soft cloth to clean the unit. Take a dry cloth and wipe the unit dry. Remember to avoid having liquids seep into the internal components and areas of the medical panel PC unit. WMP-24C/24F User’s manual...
Page 9
PC unit, make sure service technicians use replacement parts specified by the manufacturer, or those with the same characteristics and performance as the original parts. If unauthorized parts are used it may result in starting a fire, electrical shock and/or other dangers. WMP-24C/24F User’s manual viii...
Page 10
The mark on electrical and electronic products only applies to the current European Union Member States. WMP-24C/24F User’s manual...
Page 11
IEC 60601-1-1. The unit is for exclusive interconnection with IEC 60601-1 certified equipment in the patient environment and IEC 60XXX certified equipment outside of the patient environment. If in doubt, consult the technical services department or your local representative. WMP-24C/24F User’s manual...
Page 12
C) Caution: This adapter Sinpro HPU180A-108 is a forming part of the medical device Contact information: Wincomm Corporation 3F, No.14, Prosperity Road II, Science-Based Industrial Park, Hsinchu, Taiwan 300, R.O.C TEL: (886) 3 5780000 E-Mail: Sales@wincomm.com.tw WMP-24C/24F User’s manual...
Disconnect Device ............25 BIOS Setup ............26 Appendix .............. 42 A. Jumper settings and Connectors ..... 42 B. L type Stand (optional kit) ......... 62 C. Battery Pack Specifications (optional kit) ..63 D. Scrap Computer Recycling ........ 64 WMP-24C/24F User’s manual...
Introduction Product Description The WMP-24C/24F Medical Panel PC are based on Intel 6th generation Core i processor which can deliver faster graphic with higher CPU performance. It accommodates two SATA III devices and up to 32GB DDR4 SODIMM. The high brightness LCD, Low noise (WMP-24F) / Fanless...
Before you begin installing your Medical Station, please make sure that the following items have been shipped: The WMP-24F or WMP-24C Medical Panel PC unit User manual, chipset drivers Power Adapter x 1 (Mf: Sinpro, type/model: HPU180A-108) ...
USB/LAN/COM isolated module by different configuration Optional DVD-RW or Smart card reader by different configuration Optional WLAN/Bluetooth module with inner antenna, mSATA card, battery pack, Auto focus 5M pixel camera, desktop stand and project with RFID solution WMP-24C/24F User’s manual...
One M.2 Type E slot One PCI-E expansion slot Power // Audio adjustment (+)(-) // brightness (+)(-) Button // Reading Light // Video input selection // LCD on/off // Clean me(auto release after 1 minute) // Fn WMP-24C/24F User’s manual...
Page 18
(The isolated ports verified through Dielectric test 4000Vac only) LCD Specifications Display Type 23.8” LED backlight LCD Max. Resolution 1920 x 1080 (Full HD) Contrast Ratio 3000 : 1 (Typ) 274.5 (per one triad) × 274.5 Pixel Pitch (um) Luminance (cd/m2) 250 (TYP) WMP-24C/24F User’s manual...
Page 19
3mm ABS + PC TYPE Plastic housing Dimension (WxHxD) 606 x 398 x 65.6 mm WMP-24F: 10.83kg (w/o power adapter) Net Weight WMP-24C: 10.80kg (w/o power adapter) Packing Filler Environmental Specifications Operating: 0°C to 35°C (32°F ~95°F) with Sinpro Adapter Temperature Storage, Transportation: -20°C to 60°C (-4°F...
Guidance and manufacturer’s declaration – electromagnetic emissions The model WMP-24C/24F is intended for use in the electromagnetic environment specified below. The customer or the user of the model WMP-24C/24F should assure that it is used in such an environment. Electromagnetic environment – Emissions test Compliance...
Page 21
The model WMP-24C/24F is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the model WMP-24C/24F can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment...
Guidance and manufacturer’s declaration – electromagnetic immunity The model WMP-24C/24F is intended for use in the electromagnetic environment specified below. The customer or the user of the model WMP-24C/24F should assure that it is used in such an environment. Immunity test IEC 60601 Compliance Electromagnetic environment –...
Guidance and manufacturer’s declaration – electromagnetic immunity The model WMP-24C/24F is intended for use in the electromagnetic environment specified below. The customer or the user of the model WMP-24C/24F should assure that it is used in such an environment. Immunity Electromagnetic environment –...
Page 24
If the measured field strength in the location in which the model WMP-24C/24F is used exceeds the applicable RF compliance level above, the model WMP-24C/24F should be observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as reorienting or relocating the model WMP-24C/24F.
Cleaning/Disinfecting Steps: 1. Wipe the WMP-24C/24F with a dry clean cloth. 2. Operate with manufacturer’s instructions or hospital protocol. Cautions: Do not immerse or rinse the WMP-24C/24F and its peripherals. If you accidentally spill liquid on the device, disconnect the unit from the power source.
Page 26
“F11” key, go into BIOS quick boot menu, select “USB-CD ROM”, WAIT FOR 20 SECONDS, then press enter, system OS will boot up from USB-CD/DVD drive directly. Notice: The installation is only to be carried out by manufacturer trained and authorized personnel. WMP-24C/24F User’s manual...
1-2 Down. Battery1(Green) & Battery2(Amber): LED 1 LED 2 (Charge/Discharge/Low) (Batt present/ not present) In charge blinking Discharge Full charge Low battery blinking blinking No battery 2. Power Button (with LED status indicator: ON: Green, OFF: dark) Operation: always on. WMP-24C/24F User’s manual...
Page 34
10. Clean me (with LED status indicator: ON: Amber, OFF: dark) a. Keep on contacting 5 seconds to active b. keep contacting 5 seconds to release c. auto release after 60 seconds 11. Fn: Function key (with LED status indicator: ON: Green, OFF: dark) WMP-24C/24F User’s manual...
Page 35
Side View Standard model without Customized model with door DVD (or Smart card reader) Rear View WMP-24F (Fan) WMP-24C (Fanless) WMP-24C/24F User’s manual...
Page 36
8. DC-in 3. RS232/RS422/RS485 x 1 9. PCI-E/PCI expansion (RS-485 auto flow support) 10. Line-out 4. USB 3.1 x 2 11. Microphone-in 5. USB 3.0 x 2 12. DP Port x 2 (Output) 6. USB 2.0 x 2 WMP-24C/24F User’s manual...
Page 37
I/O parts (Isolated version) isolation isolated COM 4KV isolated RS-232 x 1, RS-232/422/485 x 1 isolated USB 4KV isolated USB 2.0 x 1 (Full speed) isolated LAN 4KV isolated Lan x 1 (Gigabit) WMP-24C/24F User’s manual...
Unplug the power cord from the power adapter jack to disconnect the device. Turn off the system: Turning off WMP-24C/24F properly is important for system reliability. 1. On the start menu, click “Shut down” and select “OK”. WMP-24C/24F User’s manual...
<PgUp> and <PgDn> keys to change entries, <F1> for help and <Esc> to quit. When you enter the Setup utility, the Main Menu screen will appear on the screen. The Main Menu allows you to select from various setup functions and exit choices. WMP-24C/24F User’s manual...
Page 40
This section provides information on the BIOS information, Embedded controller information and Battery information System Date Set the system date. Use the <Tab> key to switch between data elements. System Time Set the system time. Use the <Tab> key to switch between time elements. WMP-24C/24F User’s manual...
Page 41
AMT Configuration Intel AMT Enable/Disable Intel (R) Active Management Technology BIOS Extension. Note : iAMT H/W is always enabled. This option just controls the BIOS extension execution. If enabled, this requires additional firmware in the SPI device. WMP-24C/24F User’s manual...
Page 42
Enable or Disable Serial Port (COM). Change Settings Select an optimal settings for super IO Device. Serial Port 4 Configuration Serial Port Enable or Disable Serial Port (COM). Change Settings Select an optimal settings for super IO Device. WMP-24C/24F User’s manual...
Page 43
Enable / Disable Turbo Mode. Battery Mode Power Limit Enable / Disable battery mode power limit function. Embedded Controller Configuration Battery off Time Number of seconds of cut off battery output after system shutdowns.0~600 second(s) 0 means disable battery off function. WMP-24C/24F User’s manual...
Page 44
RAID OROM/RST driver will refer to the SWFM configuration to enable or disable the storage features. Serial-ATA Port 0 Enable / Disable Serial ATA Port 0. Port 0 Enable or Disable SATA Port HotPlug Designates this port as hot Pluggable. WMP-24C/24F User’s manual...
Page 45
Identify the SATA Topology if it is Default or ISATA or Flex or DirectConnect or M2 Device Sleep mSATA for RTD3. SATA DEVSLEP Idle Timeout config Enable/Disable SATA DTIO Config Serial-ATA Port 3 Enable / Disable Serial ATA Port 0. Port 0 Enable or Disable SATA Port WMP-24C/24F User’s manual...
Page 46
Hard Disk Drive. Topology Identify the SATA Topology if it is Default or ISATA or Flex or DirectConnect or M2 Device Sleep mSATA for RTD3. SATA DEVSLEP Idle Timeout config Enable/Disable SATA DTIO Config Info Report Configuration Post Report WMP-24C/24F User’s manual...
Page 47
USB mass storage device Start Unit command time-out Device power-up delay Maximun time the device will take before it properly reports itself to the Host Controller. 'Auto' uses default value: for a Root port the delay is taken from Hub descriptor. WMP-24C/24F User’s manual...
Page 48
PCH PCIE Ports Primary Display Select which of IGFX/PEG/PCI Graphics device should be Primary Display or Select SG for Switchable GFX. Internal Graphics Keep IGFX enabled based on the setup options GTT Size Select the GTT Size Aperture Size WMP-24C/24F User’s manual...
Page 49
Enable or disable onboard NIC DeepSx Power Policies Configure the DeepSx Mode Configuration Wake on LAN Enable or disable integrated LAN to wake the system.(The wake ON LAN cannot be disabled if ME is on at SX state.) WMP-24C/24F User’s manual...
Page 50
SLP_LAN# Low on DC Power Enable/Disable SLP_LAN# Low on DC power. Wake on WLAN Enable Enable/Disable PCI Express Wireless LAN to wake the system. Restore AC Power Loss Select AC power state when power is re-applied after a power failure. WMP-24C/24F User’s manual...
Page 51
Platform key(PK). 2. CSM function is disabled. Secure Boot Mode Secure Boot mode selector. 'Custom' Mode enables users to change Image Execution policy and manage Secure Boot keys. Key Management Enables experienced users to modify Secure Boot variables WMP-24C/24F User’s manual...
Page 52
Enables or disables boot with initialization of a minimal set of devices required to launch active boot option. Has no effect for BBS boot options. New Boot Option Controls the placement of newly detected UEFI boot options WMP-24C/24F User’s manual...
Page 53
Reset system setup without saving the changes. Save Changes Save the changes done so far to any of setup options. Discard Changes Discard the changes done so far to any of setup options. Restore Defaults Restore/load default values for all the setup options. WMP-24C/24F User’s manual...
Page 54
Save as User Defaults Save the changes done so far as User Defaults. Restore User Defaults Restore the User Defaults to all the setup options. WMP-24C/24F User’s manual...
A. Jumper settings and Connectors This appendix gives the definitions and shows the positions of jumpers, headers and connectors. All of the configuration jumpers on WMP-24C/24F are in the proper position. Note: Some of jumpers or connectors will be removed base on system configuration.
Page 56
Jumper Setting SATA DOM 1-2 ---power +5V SATA Port 2-3 (GND) default JP5 –ME Clear Description Jumper Setting Clear ME 1-2 (NC) default JP6 –CMOS Clear Description Jumper Setting Normal Open 1-2 (default) CMOS Clear WMP-24C/24F User’s manual...
Page 58
PJ4 Power Jack Connector Pin # Signal Description DC In DC In Ground Ground Ground J1 – Inverter connect Pin # Signal Description +12VS +12VS Backlight Adjust Backlight Enable Ground Ground J2 – CPU PWM FAN WMP-24C/24F User’s manual...
Page 59
Pin # Signal Description +12VS CPU_FAN_RPM FAN_PWM J3 – PCI POWER Pin # Signal Description Ground J4/J5/J6/J7/J8 – Internal USB Interface Pin # Signal Description +5VSB +5VSB Ground Ground J9 – VEDIO-IN WMP-24C/24F User’s manual...
Page 60
Signal Description Pin # J9(VEDIO-IN) DVI_DATA0+ DVI_DATA2+ DVI_DATA0- DVI_DATA2- DVI_DATA1+ DVI_DATA1- DET_DVI DVI_5V DVI_CLK+ HPD_DVI DVI_CLK- J10 – SYSTEM FAN Signal Description Pin # J10(System Fan) SYS_PWM WMP-24C/24F User’s manual...
Page 61
KEY A KEY A LED2#(O)(OD) KEY E KEY E KEY E KEY E KEY E KEY E KEY E KEY E PETP0 PETN0 CLINK Reset(I)(0/3.3V) CLINK DATA (I/O) PERP0 CLINK CLK(I/O) PERN0 COEX3(I/O)(0/1.8V) COEX2(I/O)(0/1.8V) REFCLKP0 COEX1(I/O)(0/1.8V) REFCLKN0 SUSCLK(32kHz)(I)(0/3.3V) WMP-24C/24F User’s manual...
Page 66
J19 / J23 – Standard SATA / SATA DOM Interface Pin # Signal Description Ground Ground Ground / +5VS (jump select SATA DOM only) J20 – DICOM JTAG Pin # Signal Description Pin # Signal Description +3.3VS 394_C2D +3.3VS Pull High WMP-24C/24F User’s manual...
Page 67
394_RST# J21 – CPU Interface (Please refer to FCLGA1151) J22 – CAP Front Bezel Button Connector Pin # Signal Description +5V_AWS +3.3_AWS KP_SCL KP_SDA PWR_LED# WMP-24C/24F User’s manual...
B. L type Stand (optional kit) Key Features and Benefits Similar color as WMP series 5,000 times hinge life cycle Specifications: Weight Capacity: Max 10kgs Monitor Mounting Holes VESA 100*100mm Application using Desktop stand WMP-24C/24F User’s manual...
For the computers that are no longer useful or work well, please contact with worldwide distributors for recycling. The worldwide distributors show on the following website: http://www.wincomm.com.tw/contact.aspx Note: Follow the national requirement to dispose unit WMP-24C/24F User’s manual...