ORiNG TPS-3882GT-M12-BP1 Quick Installation Manual

EN50155
Switch
Q I
I N D U S T R I A L
uick nstallation
Introduction
The TPS-3882GT-M12-BP1 series, including the
TPS-3882GT-M12-BP1-24V are managed Ethernet switches designed for
industrial applications, such as rolling stock, vehicle, and railway
applications. The switches boast EN50155 compliance and M12
connectors to ensure tight and robust connections, and guarantee
reliable operation against environmental disturbances, such as vibration and
shock. All models feature eight 10/100Base-T(X) P.S.E. ports which are able
to provide sufficient power for power-hungry devices. Therefore, you can
attach an IEEE 802.3af-compliant device to the switch without requiring
additional power. The devices also provide 1 set of bypass ports that ensure
constant network connectivity if power outage or node failure occurs. In such
situations, the device will bypass the inactive switch and continue to transfer
network traffic to the next switch in the relay.
Package Contents
The TPS-3882GT-M12-BP1 series is shipped with the following items. If any
of these items is missing or damaged, please contact your customer service
representative for assistance.
Contents Pictures
TPS-3882GT-M12-BP1/
TPS-3882GT-M12-BP1-24V
CD
QIG
Preparation
Before you begin installing the device, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Safety & Warnings
Elevated Operating Ambient: If installed in a closed environment, make sure
the operating ambient temperature is compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow: Make sure the amount of air flow required for safe operation
of the equipment is not compromised during installation.
Mechanical Loading: Make sure the mounting of the equipment is not in a
hazardous condition due to uneven mechanical loading.
Circuit Overloading: Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
Q I G
TPS-3882GT-M12-BP1
TPS-3882GT-M12-BP1
G
uide
Dimension
TPS-3882GT-M12-BP1 and
Panel Layouts
Front View
Number
1
TPS-3882GT-M12-BP1
1
Reset
PWR1 PWR2 R.M. Ring Fault
2 3 4 5 6
7
Relay N.C.
3A@24VDC
1
Relay Output
8
RXD TXD
N.C.
N.C. GND
RS-232, 9600bps, 8, N, 1 Console
1
9
V1+ V2+
10
V1- V2- Power
Installation
Wall-mount
The device can be fixed to the wall. Follow the steps below to install the device on the wall.
Step 1: Hold the
Step 2: Insert four screws through the large opening of the keyhole-shaped apertures at the
top and bottom of the unit and fasten the screw to the wall with a screwdriver.
Step 3: Slide the
1907-2-29-TPS3882GTBP1-1.0
Tx+ Rx+ Tx+ Rx+
Tx+: PoE Vout+
Tx- : PoE Vout+
Rx+: PoE Vout-
Rx- : PoE Vout-
Rx- Tx- Rx- Tx-
P1~P8 P9~P16
TPS-3882GT-M12-BP1
Reset LNK/ACT LNK/ACT
PWR1 PWR2 R.M. Ring Fault LNK/ACT
PoE
DPX/COL DPX/COL
G2 100M
Relay N.C. P4 P8 P12 P16
3A@24VDC
1 2
Relay Output LNK/ACT LNK/ACT
7 3
PoE 6 4
5
DPX/COL DPX/COL 8
RXD TXD P3 P7 P11 P15
1 BI_DC+
N.C. 2 BI_DD+
Power 3 BI_DD-
N.C. GND Failure 4 BI_DA-
RS-232, 9600bps, 8, N, 1 Console LNK/ACT LNK/ACT Bypass 5 BI_DB+
6 BI_DA+ 7 BI_DC-
PoE 8 BI_DB-
DPX/COL DPX/COL
P2 P6 P10 P14
LNK/ACT LNK/ACT LNK/ACT
V1+ V2+ PoE
DPX/COL DPX/COL 100M
V1- V2- Power P1 P5 P9 P13 G1
1. Reset button
2. Power1 status LED
3. Power2 status LED
4. R.M. status LED
5. Ring status LED
Tx+ Rx+ Tx+ Rx+
Tx+: PoE Vout+
Tx- : PoE Vout+ 6. Fault LED
Rx+: PoE Vout-
Rx- : PoE Vout-
Rx- Tx- Rx- Tx-
14 15
11 7. Relay output port
P1~P8 P9~P16
18
8. Console port
LNK/ACT LNK/ACT LNK/ACT
17
PoE
19 9. Power connector
DPX/COL DPX/COL
G2 100M
P4 P8 P12 P16
12
16 10. PoE fast Ethernet ports (P1~P8)
1 2
LNK/ACT LNK/ACT
7 3
11. LNK/ACT indicator for PoE Fast Ethernet
PoE 6 4
5 8
DPX/COL DPX/COL
port
P3 P7 P11 P15
1 BI_DC+
13 2 BI_DD+
Power 3 BI_DD-
Failure 4 BI_DA-
12. PoE status LED for PoE Fast Ethernet
LNK/ACT LNK/ACT Bypass 5 BI_DB+
6 BI_DA+
7 BI_DC-
PoE 8 BI_DB-
ports
DPX/COL DPX/COL
P2 P6 P10 P14
13. Duplex/collision indicator for
LNK/ACT LNK/ACT
LNK/ACT
PoE Fast Ethernet port
PoE
DPX/COL DPX/COL
100M 14. Fast Ethernet Ports (P9 ~ P16)
P1 P5 P9 P13 G1
15. LNK/ACT indicator for Ethernet ports
16. Duplex/collision status LED for
Ethernet ports
17. Gigabit Ethernet port
18. LNK/ACT indicator for Gigabit Ethernet
ports
19. 100Mbps indicator for Gigabit Ethernet
ports
d evice upright against the wall
d evice downwards and tighten the four screws for added stability.
Instead of screwing the screws in all the way, it is advised to
leave a space of about 2mm to allow room for sliding the
switch between the wall and the screws.
PRINTED ON RECYCLED PAPER
EN50155 18-port managed
PoE Ethernet switch
Wiring
For pin assignments of power, console and relay output ports, please refer to the following tables.
Grounding
Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection from the grounding pin on the power connector to the grounding
surface prior to connecting devices.
Power port pinouts
The device supports two sets of power supplies and uses the M23 5-pin
female connector on the front panel for the dual power inputs.
Step 1: Insert a power cable to the power connector on the device.
Step 2: Rotate the outer ring of the cable connector until a snug fit is
achieved. Make sure the connection is tight.
Console port pinouts
RXD TXD
N.C.
N.C. GND
RS-232, 9600bps, 8, N, 1
Relay output port pinouts
The switch uses the M12 A-coded 5-pin male connector on
the front panel for relay output. Use a power cord with an
M12 A-coded 5-pin female connector to connect the relay.
The relay contacts will detect user-configured events and
form an open circuit when an event is triggered.
Network Connection
The switch has sixteen 10/100Base-T(X) and two 10/100/1000Base-T(X) Ethernet ports in the form
of M12 connector. Depending on the link type, the switch uses CAT 3, 4, 5,5e UTP cables to
connect to network devices (PCs, servers, switches, routers, or hubs). Please refer to the
following table for cable specifications.
Cable Type Max. Length Connector
4-pin female M12
10BASE-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft)
D-coding connector
4-pin female M12
100BASE-TX Cat. 5 100-ohm UTP UTP 100 m (328 ft)
D-coding connector
8-pin female M12
1000BASE-T Cat. 5/Cat. 5e 100-ohm UTP UTP 100 m (328 ft)
A-coding connector
For pin assignments of the LAN ports, please refer to the following tables.
4-Pin Fast Ethernet Port Definition
2 1
Pin No. PoE Port Description
Tx+ Rx+
#1 RD+ with PoE power input -
#2 TD+ with PoE power input +
Rx- Tx-
3 4
#3 RD- with PoE power input -
#4 TD- with PoE power input +
8-Pin Gigabit Port Definition
M12 Pin Description Pin No.
1 2
Pin No. Description #1
7 3
6 4
#1 BI_DC+ #2
5 8
#2 BI_DD+ #3
#4
#3 BI_DD-
#4 BI_DA-
#5 BI_DB+
#6 BI_DA+
#7 BI_DC-
#8 BI_DB-
Quick Installation Guide
Version 1.0
V1+ V2+
V1- V2-
Relay
N.C.
3A@24VDC
Non-PoE Port Description
RD+ power input -
TD+ power input +
RD- power input -
TD- power input +
Description
TD+ power input +
TD- power input +
RD+ power input -
RD- PoE power input -