ORiNG IGS-9084GP Quick Installation Manual

GIGABIT
SWITCH
Q I
uick nstallation
I N D U S T R I A L
Introduction
The IGS-9084GP series is a managed Ethernet switch with
8x10/100/1000Base-T(X) ports and 4x100/1000Base-X SFP ports. With
complete support of Ethernet redundancy protocols, O-Ring (recovery time
< 30ms for over 250 connected devices) and MSTP (RSTP/STP compatible)
can protect your mission-critical applications from network interruptions or
temporary malfunctions. With a wide operating temperature from -40~70 C,
the device can be managed centrally via ORing's proprietary Open-Vision
platform as well as via Web-based interfaces, Telnet and console (CLI).
Package Contents
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative for
assistance.
Contents Pictures Number
IGS-9084GP
CD
DIN-rail Kit
Wall-mount Kit
Console Cable
QIG
Preparation
Before you begin installing the switch, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Safety & Warnings
Elevated Operating Ambient: If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may be
greater than room ambient. Therefore, consideration should be given to
installing the equipment in an environment compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow: Installation of the equipment in a rack should be such
that the amount of air flow required for safe operation of the equipment is
not compromised.
Mechanical Loading: Mounting of the equipment in the rack should be
such that a hazardous condition is not achieved due to uneven mechanical
loading.
Q I G
IGS-9084GP
G
uide
o
Dimension
96.4
70.5 15.0 10.9
G12
PWR
PWR1
G11 PWR2
G10
G9
100/1000X
G8 G7
G6 G5
G4 G3
G2 G1
10/100/1000T
IGS-9084GP
X 1
Panel Layouts
X 1
Front View
X 1
12
11
G12
G11
X 2
G10
G9
100/1000X
8
X 1
G8 G7
9
10
G6 G5
G4 G3
X 1
G2 G1
10/100/1000T
Rear View
1 1
1. Wall-mount screw holes
2. Din-rail screw holes
1907-2-29-IGS9084GP-1.0
IGS-9084GP
Circuit Overloading: Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits might have
on overcurrent protection and supply wiring. Appropriate consideration of equipment
nameplate ratings should be used when addressing this concern.
30.0
87.0
58.0
48.0
105.5
1. Power LED
1
PWR
2. PWR1 LED
PWR1 2
3
PWR2
3. PWR2 LED
4
5
4. R.M. status LED
6
5. Ring status LED
7
6. Faulty relay indicator
7. Console port
8. Link/action LED for Gigabit Ethernet ports
9. Duplex LED for Gigabit Ethernet ports
10. Gigabit Ethernet ports
11. SFP port
12. Link/action LED for SFP port
IGS-9084GP
Top Panel
PWR-2 Fault PWR-1
1 1A@24V
V2- V2+ V1- V1+ DC 48V
2
2
1. Terminal blocks: PWR1, PWR2
(12-48V DC), Relay
2. Ground wire.
PRINTED ON RECYCLED PAPER
Industrial Managed Gigabit Switch
Installation
DIN-rail Installation
Step 1: Slant the switch and screw the Din-rail kit onto the back of the switch, right in
the middle of the back panel.
Step 2: Slide the switch onto a DIN-rail from the Din-rail kit and make sure the switch
clicks into the rail firmly.
R2.5
R3.95
95.9
Wall-mounting
Step 1: Screw the two pieces of wall-mount kits onto both ends of the rear panel of the
switch. A total of six screws are required, as shown below.
Step 2: Use the switch, with wall mount plates attached, as a guide to mark the
correct locations of the four screws.
Step 3: Insert a screw head through the large parts of the keyhole-shaped apertures,
and then slide the switch downwards. Tighten the screws for added stability.
Network Connection
The switch provides standard Ethernet ports. According to the link type, the switch uses
CAT 3,4,5,5e UTP cables to connect to any other network devices (PCs, servers,
switches, routers, or hubs). Please refer to the following table for cable
specifications.
Cable Types and Specifications:
Cable Type
10BASE-T Cat. 3, 4, 5 100-ohm
100BASE-TX Cat. 5 100-ohm UTP
1000BASE-T Cat. 5 / Cat. 5e 100-ohm UTP
Version 1.0
G12
PWR
PWR1
PWR2
G11
G10
G9
100/1000X
G8 G7
G6 G5
G4 G3
G2 G1
10/100/1000T
IGS-9084GP
Max. Length Connector
UTP 100 m (328 ft) RJ-45
UTP 100 m (328 ft) RJ-45
UTP 100 m (328 ft) RJ-45
Quick Installation Guide