ORiNG TPS-1080-M12 Quick Installation Manual

EN50155
Switch
Q I
I N D U S T R I A L
uick nstallation
Introduction
The TPS-1080-M12/-24V and TPS-1080-M12-BP2/-24V
Ethernet switches with 8x10/100Base-T(X) P.S.E. ports. Designed for
industrial applications, such as rolling stock, vehicle, and railway
applications, these two models boast EN50155 compliance and M12
connectors to ensure tight and robust connections, and guarantee reliable
operation against environmental disturbances, such as vibration and shock.
The P.S.E. ports are able to provide sufficient power for those power-hungry
devices with up to 30W per port. Therefore, you can attach an IEEE 802.3at-
compliant device to the switch without requiring additional power. The -BP2
model also provides two sets of bypass ports that ensure constant network
connectivity during power failure. Even if the switch loses power, traffic will
continue to flow unimpeded through the link.
Package Contents
The device is shipped with the following items. If any of these items is missing
or damaged, please contact your customer service representative for
assistance.
Contents Pictures
TPS-1080-M12 or
TPS-1080-M12-BP2 or
TPS-1080-M12-24V or
TPS-1080-M12-BP2-24V
QIG
Preparation
Before you begin installing the device, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Safety & Warnings
Elevated Operating Ambient: If installed in a closed environment, make sure
the operating ambient temperature is compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow: Make sure the amount of air flow required for safe operation
of the equipment is not compromised during installation.
Mechanical Loading: Make sure the mounting of the equipment is not in a
hazardous condition due to uneven mechanical loading.
Circuit Overloading: Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
Q I G
TPS-1080-M12 Series
TPS-1080-M12 Series
G
uide

Dimension

are unmanaged PoE
15.0
65.0 21.3
TPS-1080-M12/-24V

Panel Layouts

Front View
Number
1
TPS-1080-M12
PWR PWR1 PWR2 Fault
1
2
3
4 Tx+ Rx+
Tx+: PoE Vout+
Tx- : PoE Vout+
1 Rx+: PoE Vout-
Rx- : PoE Vout-
Rx- Tx-
V1+ V2+
V1- V2-
5
Power

Installation

Wall-mount
The device can be fixed to the wall. Follow the steps below to install the device on the wall.
Step 1: Hold the d
Step 2: Insert four screws through the large opening of the keyhole-shaped apertures at the
top and bottom of the unit and fasten the screw to the wall with a screwdriver.
Step 3: Slide the
1907-2-29-TPS1080M12-1.0
125.0
86.0
56.5
R2.5
15.0
R4.00
Relay N.C. Relay Output
3A@24VDC
TPS-1080-M12 TPS-1080-M12-BP2
PWR PWR1 PWR2 Fault PWR PWR1 PWR2
LNK/ACT
DPX/COL
Tx+ Rx+ PoE Tx+
Tx+: PoE Vout+ P4 P8 Tx+: PoE Vout+
Tx- : PoE Vout+ Tx- : PoE Vout+
Rx+: PoE Vout- Rx+: PoE Vout-
Rx- : PoE Vout- Rx- : PoE Vout-
Rx- Tx- Rx-
LNK/ACT
DPX/COL
PoE
P3 P7
V1+ V2+ LNK/ACT V1+
DPX/COL
V1- V2- V1-
PoE
P2 P6
LNK/ACT
DPX/COL
PoE
P1 P5
Power Power
65.0 21.3
TPS-1080-M12-BP2/-24V
1. Power status LED
Relay Relay Output
N.C.
3A@24VDC 2. Power1 status LED
6
3. Power2 status LED
4. Fault LED
LNK/ACT
DPX/COL
5. Power input port
PoE
P4 P8
6. Relay output port
LNK/ACT
7. LAN port LNK/ACT LED
DPX/COL
PoE 8. LAN port Duplex/Collision LED
P3 P7
7
9. Ethernet ports
LNK/ACT
(P5-P8 of TPS-1080-M12-BP2/-24V are bypass ports)
DPX/COL
PoE
P2 P6
10. PoE status LED
LNK/ACT
8
DPX/COL
PoE
P1 P5
9 10 9
evice upright against the wall
d evice downwards and tighten the four screws for added stability.
Instead of screwing the screws in all the way, it is advised to
leave a space of about 2mm to allow room for sliding the switch
between the wall and the screws.
PRINTED ON RECYCLED PAPER
EN50155 8-port unmanaged
PoE Ethernet switch

Wiring

For pin assignments of power, console and relay output ports, please refer to the following tables.

Grounding

Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection from the grounding pin on the power connector to the grounding
surface prior to connecting devices.
125.0
86.0
56.5
R2.5

Power port pinouts

R4.00
The device supports two sets of power supplies and uses the M23 5-pin
Relay N.C. Relay Output
3A@24VDC
female connector on the front panel for the dual power inputs.
Fault
LNK/ACT
Step 1: Insert a power cable to the power connector on the device.
DPX/COL
Rx+ PoE
P4 P8
Step 2: Rotate the outer ring of the cable connector until a snug fit is
Tx-
LNK/ACT
DPX/COL
PoE Power
P3 P7 Failure achieved. Make sure the connection is tight.
Bypass
V2+ LNK/ACT
DPX/COL
V2-
PoE
P2 P6
LNK/ACT
DPX/COL
PoE

Relay output port pinouts

P1 P5
The switch uses the M12 A-coded 5-pin male connector on
the front panel for relay output. Use a power cord with an
M12 A-coded 5-pin female connector to connect the relay.
The relay contacts will detect user-configured events and
form an open circuit when an event is triggered.

Network Connection

The switch has eight 10/100Base-T(X) Ethernet ports in the form of M12 connector. These
ports are PoE-enabled, and thus can deliver power over the same Ethernet cable.
Depending on the link type, the switch uses CAT 3, 4, 5,5e UTP cables to connect to network
devices (PCs, servers, switches, routers, or hubs). Please refer to the following table for cable
Specifications.
Cable Type Max. Length
10BASE-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft)
100BASE-TX Cat. 5 100-ohm UTP UTP 100 m (328 ft)

M12/4P PoE Pin Definition

For pin assignments of the LAN ports, please refer to the following tables.
Tx+ Rx+
Pin No.
Rx- Tx- TX+
TX-
RX+
RX-

Configurations

After installing the switch and connecting cables, start the
power. The green power LED should turn on. Please refer to the following tablet
for LED indication.
Version 1.0
V1+ V2+
V1- V2-
Relay
N.C.
3A@24VDC
Connector
4-pin female M12
D-coding connector
4-pin female M12
D-coding connector

10/100Base-T(X) P.S.E. RJ-45 port

Description
TX+ with PoE Power input +
TX- with PoE Power input +
RX+ with PoE Power input -
RX- with PoE Power input -
d evice by turning on
Quick Installation Guide