ORiNG TPS-3162GT-M12-BP1 Quick Installation Manual

EN50155
Switch
Q I
I N D U S T R I A L
uick nstallation

Introduction

The TPS-3162GT-M12-BP1 series, including the
and TPS-3162GT-M12-BP1-24V model,
designed for industrial applications, such as rolling stock, vehicle, and
railway applications. The series boasts EN50155 compliance and M12
connectors to ensure tight and robust connections, and guarantee
reliable operation against environmental disturbances, such as vibration
and shock. All models feature sixteen 10/100Base-T(X) P.S.E. ports which
are able to provide sufficient power for power-hungry devices. Therefore, you
can attach an IEEE 802.3af-compliant device to the switch without requiring
additional power. The series also provides 1 set of bypass ports that
ensure constant network connectivity if power outage or node failure
occurs. In such situations, the device will bypass the inactive switch and
continue to transfer network traffic to the next switch in the relay.
Package Contents
The TPS-3162GT-M12-BP1 series is shipped with the following items. If any
of these items is missing or damaged, please contact your customer service
representative for assistance.
Contents Pictures
TPS-3162GT-M12-BP1/
TPS-3162GT-M12-BP1-24V
CD
QIG
Preparation
Before you begin installing the device, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Safety & Warnings
Elevated Operating Ambient: If installed in a closed environment, make sure
the operating ambient temperature is compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow: Make sure the amount of air flow required for safe operation
of the equipment is not compromised during installation.
Mechanical Loading: Make sure the mounting of the equipment is not in a
hazardous condition due to uneven mechanical loading.
Circuit Overloading: Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
Q I G
TPS-3162GT-M12-BP1
TPS-3162GT-M12-BP1
G
uide

Dimension

TPS-3162GT-M12-BP1
are managed Ethernet switch

Panel Layouts

Number
Front View
1
1
TPS-3162GT-M12-BP1
1
Reset
PWR1 PWR2 R.M. Ring Fault
2 3 4 5 6
7
Relay
N.C.
3A@24VDC
1
Relay Output
8
RXD TXD
N.C.
N.C. GND
RS-232, 9600bps, 8, N, 1
Console
9
V1+ V2+
10
V1- V2-
Power

Installation

Wall-mount
The device can be fixed to the wall. Follow the steps below to install the device on the wall.
Step 1: Hold the
Step 2: Insert four screws through the large opening of the keyhole-shaped apertures at the
top and bottom of the unit and fasten the screw to the wall with a screwdriver.
Step 3: Slide the
1907-2-29-TPS3162GTBP1-1.0
Tx+ Rx+
Tx+: PoE Vout+
Tx- : PoE Vout+
Rx+: PoE Vout-
Rx- : PoE Vout-
Rx- Tx-
TPS-3162GT-M12-BP1 P1~P16
Reset
PWR1 PWR2 R.M. Ring Fault LNK/ACT LNK/ACT LNK/ACT
PoE PoE
DPX/COL DPX/COL 100M
P4 P8 P12 P16 G2
Relay N.C.
3A@24VDC
1 2
Relay Output LNK/ACT LNK/ACT 7 3
PoE PoE 6 4
5 8
DPX/COL DPX/COL
RXD TXD P3 P7 P11 P15
1 BI_DC+
N.C. Power 2 BI_DD+
Failure 4 BI_DA- 3 BI_DD-
N.C. GND Bypass 5 BI_DB+
RS-232, 9600bps, 8, N, 1 Console LNK/ACT LNK/ACT 6 BI_DA+
7 BI_DC-
PoE PoE 8 BI_DB-
DPX/COL DPX/COL
P2 P6 P10 P14
LNK/ACT LNK/ACT
LNK/ACT
V1+ V2+ PoE PoE
DPX/COL DPX/COL G1 100M
V1- V2- Power P1 P5 P9 P13
1. Reset button
2. Power1 status LED
3. Power2 status LED
4. R.M. status LED
Tx+ Rx+
Tx+: PoE Vout+
Tx- : PoE Vout+
Rx+: PoE Vout- 5. Ring status LED
Rx- : PoE Vout-
Rx- Tx-
11
P1~P16 6. Fault LED
15
LNK/ACT LNK/ACT
LNK/ACT 7. Relay output port
14
PoE PoE
16
8. Console port
DPX/COL DPX/COL 100M
G2
P4 P8 P12 P16
12
9. Power connector
1 2
LNK/ACT LNK/ACT
7 3
PoE PoE 6 4 10. PoE Fast Ethernet ports
5 8
DPX/COL DPX/COL
P3 P7 P11 P15
11. LNK/ACT indicator for PoE Fast Ethernet
1 BI_DC+
13 2 BI_DD+
Power
3 BI_DD-
Failure 4 BI_DA-
LNK/ACT LNK/ACT Bypass 5 BI_DB+ port
6 BI_DA+
7 BI_DC-
PoE PoE 8 BI_DB-
DPX/COL DPX/COL 12. PoE status LED for PoE Fast Ethernet ports
P2 P6 P10 P14
13. Duplex/collision indicator for
LNK/ACT LNK/ACT LNK/ACT
PoE PoE PoE Fast Ethernet port
DPX/COL DPX/COL
G1 100M
P1 P5 P9 P13 14. Gigabit Ethernet ports
15. LNK/ACT indicator for Gigabit Ethernet
port
16. Speed indicator for Gigabit Ethernet port
d evice upright against the wall
d evice downwards and tighten the four screws for added stability.
Instead of screwing the screws in all the way, it is advised to
leave a space of about 2mm to allow room for sliding the
switch between the wall and the screws.
PRINTED ON RECYCLED PAPER
EN50155 18-port managed
PoE Ethernet switch

Wiring

For pin assignments of power, console and relay output ports, please refer to the following tables.

Grounding

Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection from the grounding pin on the power connector to the grounding
surface prior to connecting devices.

Power port pinouts

The device supports two sets of power supplies and uses the M23 5-pin
female connector on the front panel for the dual power inputs.
Step 1: Insert a power cable to the power connector on the device.
Step 2: Rotate the outer ring of the cable connector until a snug fit is
achieved. Make sure the connection is tight.
Console port pinouts
RXD TXD
N.C.
N.C. GND
RS-232, 9600bps, 8, N, 1

Relay output port pinouts

The switch uses the M12 A-coded 5-pin male connector on
the front panel for relay output. Use a power cord with an
M12 A-coded 5-pin female connector to connect the relay.
The relay contacts will detect user-configured events and
form an open circuit when an event is triggered.

Network Connection

The switch has sixteen 10/100Base-T(X) and two 10/100/1000Base-T(X) Ethernet ports in the form
of M12 connector. Depending on the link type, the switch uses CAT 3, 4, 5,5e UTP cables to
connect to network devices (PCs, servers, switches, routers, or hubs). Please refer to the
following table for cable specifications.
Cable Type Max. Length Connector
4-pin female M12
10BASE-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft)
D-coding connector
4-pin female M12
100BASE-TX Cat. 5 100-ohm UTP UTP 100 m (328 ft)
D-coding connector
8-pin female M12
1000BASE-T Cat. 5/Cat. 5e 100-ohm UTP UTP 100 m (328 ft)
A-coding connector
For pin assignments of the LAN ports, please refer to the following tables.

4-Pin PoE Port Definition

2 1
Tx+ Rx+
Pin No. Description
#1 RD+ with PoE power input -
Rx- Tx- #2 TD+ with PoE power input +
3 4
#3 RD- with PoE power input -
#4 TD- with PoE power input +

8-Pin Gigabit Port Definition

M12 Pin Description
1 2
Pin No. Description
7 3
6 4
#1 BI_DC+
5 8
#2 BI_DD+
#3 BI_DD-
#4 BI_DA-
#5 BI_DB+
#6 BI_DA+
#7 BI_DC-
#8 BI_DB-
Quick Installation Guide
Version 1.0
V1+ V2+
V1- V2-
Relay
N.C.
3A@24VDC