Table of Contents
Advertisement
VPS/PDC Default
Programme VPS/PDC is a system of telling the VCR when a
programme actually starts. Typically, when you want to record a
programme you will tell the VCR to start recording, probably, five
minutes before the advertised starting time of the programme and
to finish ten minutes or so after the programme is due to finish. So
PROG
OPTIONS
INSTALL
even if the programme starts early or finishes late you will normally
still get to see what you wanted to record. However when live
BONUS
CLOCK
BONUS
LANG
programmes over-run or the day's television schedule is changed
EASY OPERATION
from that advertised, you may miss the desired programme which
may have been delayed or even cancelled. With VPS/PDC the VCR
➛❿!!
OK
END:
MENU
$ ❷!!
will wait until the signal is sent to confirm the programme is
starting and the VCR will record the programme even if it is two or
more, hours late.
1
Press the MENU button on the remote control.
BONUS
PDC/VPS DEFAULT
:OFF
SHOWVIEW EXTEND
:OFF
2
Press the corresponding
AUTO POWER OFF
:OFF
EASY OPERATION
REPEAT PLAY
:OFF
NO. OF
INTERVAL REPEAT : 5
3
Press the OK button to select this option.
INFO TAG DELETE
Result:
❿
$ ❷
END:
MENU
4
Press the corresponding
PDC/VPS DEFAULT
5
Press ❿!button to select
6
On completion, press MENU twice to exit the menu.
40
or ➛, ❿ buttons to select the
,
$
❷
option.
The
EASY OPERATION
menu is displayed.
or
buttons, until the
$
❷
option is selected.
ON
in
PDC/VPS DEFAULT
option.
ShowView EXTEND
To prevent delays or over-runs the VCR has a function called
ShowView EXTEND allowing you to extend the recording time by
up to 60 minutes.
Only use if PDC is not available or set to OFF.
1
Press the MENU button on the remote control.
2
or ➛, ❿ buttons to select the
Press the corresponding
,
$
❷
option.
EASY OPERATION
3
Press the OK button to select this option.
Result:
The
EASY OPERATION
menu is displayed.
4
Press the corresponding
or
buttons, until the
$
❷
SHOWVIEW EXTEND
option is selected.
5
Press ➛ or ❿ buttons to set the ShowView EXTEND time by
increments of 10 minutes.
6
To turn off, press ➛ or ❿ buttons repeatedly until
OFF
Using the Tape Counter
The tape counter:
Indicates the elapsed time in the play and record modes
(hours, minutes and seconds)
Is reset when a cassette is inserted in the VCR
Allows you to find the beginning of a sequence easily
If the remaining time is to be calculated correctly, you
must indicate the type of cassette being used.
1
Insert a cassette in your VCR.
2
To set the tape counter to zero at the beginning of a sequence:
Press DISP./
twice to display the counter
Press CLR/RST when you want to set the tape counter to
zero
3
When you are ready,
Start playback or Recording.
Press the
button.
To fast-froward or rewind to the sequence at which the
➛ ➛
❿ ❿
counter was set to zero, press
or
.
Some VCR information, such as the counter, can be
displayed on the television screen (unless you have
deactivated the OSD mode; refer to page 15).
Press DISP./
:
Once to display the current function, programme
number, recording speed, date, time and counter
Twice to display the counter only
Three times to display the time remaining on the
cassette
Four times to clear the display
PROG
OPTIONS
INSTALL
BONUS
CLOCK
BONUS
LANG
EASY OPERATION
➛❿!!
OK
END:
MENU
$ ❷!!
BONUS
PDC/VPS DEFAULT
:OFF
SHOWVIEW EXTEND
:OFF
AUTO POWER OFF
:OFF
REPEAT PLAY
:OFF
NO. OF
INTERVAL REPEAT : 5
shows.
INFO TAG DELETE
❿
END:
MENU
$ ❷
0:00:00
CLR/RST
F.ADV
INDEX
-/--
SELECT
TV
VCR
INPUT
2
REPEAT
AUDIO
DISP./
VOL
PROG/TRK
2
REC
MENU
41
GB
Advertisement
Table of Contents
