Vps/Pdc Default; Showview Extend; Using The Tape Counter - Samsung SV-647F Instruction Manual

VPS/PDC Default

Programme VPS/PDC is a system of telling the VCR when a
programme actually starts. Typically, when you want to record a
programme you will tell the VCR to start recording, probably, five
minutes before the advertised starting time of the programme and
to finish ten minutes or so after the programme is due to finish. So
even if the programme starts early or finishes late you will normally
PROG OPTIONS INSTALL
still get to see what you wanted to record. However when live
programmes over-run or the day's television schedule is changed
BONUS
CLOCK BONUS LANG
from that advertised, you may miss the desired programme which
FONCTIONS AVANCÉES
may have been delayed or even cancelled. With VPS/PDC the VCR
will wait until the signal is sent to confirm the programme is
➛❿!!
$ ❷!! OK FIN: MENU
starting and the VCR will record the programme even if it is two or
more, hours late.
1 Press the MENU button on the remote control.
BONUS
PDC/VPS PAR DEFAUT:NON
2
Press the corresponding
ÉTENDRE SHOWVIEW :NON
FONCTIONS AVANCÉES
VEILLE AUTO :NON
RÉPÉTITION TOTALE :NON
3 Press the OK button to select this option.
NOMBRE
RÉPÉT. PROGRAMMÉE: 5
Result:
INFO TAG DELETE
❿ 4
$ ❷ FIN: MENU Press the corresponding
PDC/VPS PAR DEFAUT
5 Press ❿!button to select
6 On completion, press MENU twice to exit the menu.
38
or ➛, ❿ buttons to select the
,
$ ❷
option.
The FONCTIONS AVANCÉES menu is displayed.
or buttons, until the
$ ❷
option is selected.
OUI in PDC/VPS PAR DEFAUT option.

ShowView EXTEND

To prevent delays or over-runs the VCR has a function called
ShowView EXTEND allowing you to extend the recording time by
up to 60 minutes.
Only use if PDC is not available or set to OFF.
1 Press the MENU button on the remote control.
2 Press the corresponding , or ➛, ❿ buttons to select the
$ ❷
FONCTIONS AVANCÉES option.
3
Press the OK button to select this option.
Result: The FONCTIONS AVANCÉES menu is displayed.
4
Press the corresponding or buttons, until the
$ ❷
ÉTENDRE SHOWVIEW option is selected.
5 Press ➛ or ❿ buttons to set the ShowView EXTEND time by
increments of 10 minutes.
6 To turn off, press ➛ or ❿ buttons repeatedly until
NON

Using the Tape Counter

The tape counter:
Indicates the elapsed time in the play and record modes
(hours, minutes and seconds)
Is reset when a cassette is inserted in the VCR
Allows you to find the beginning of a sequence easily
If the remaining time is to be calculated correctly, you
must indicate the type of cassette being used.
1
Insert a cassette in your VCR.
2 To set the tape counter to zero at the beginning of a sequence:
Press AFFICH./ twice to display the counter
Press ANNUL./RàZ when you want to set the tape counter to zero
3 When you are ready,
Start playback or Recording.
Press the button.
To fast-froward or rewind to the sequence at which the
counter was set to zero, press ➛ ➛ or ❿ ❿ .
Some VCR information, such as the counter, can be
displayed on the television screen (unless you have
deactivated the OSD mode; refer to page 14).
Press AFFICH./ :
Once to display the current function, programme
number, recording speed, date, time and counter
Twice to display the counter only
Three times to display the time remaining on the
cassette
Four times to clear the display
PROG OPTIONS INSTALL
BONUS
CLOCK BONUS LANG
FONCTIONS AVANCÉES
➛❿!!
OK FIN: MENU
$ ❷!!
BONUS
PDC/VPS PAR DEFAUT:NON
ÉTENDRE SHOWVIEW :NON
VEILLE AUTO :NON
RÉPÉTITION TOTALE :NON
NOMBRE
RÉPÉT. PROGRAMMÉE: 5
shows.
INFO TAG DELETE
❿
FIN: MENU
$ ❷
0:00:00
ANNUL./RàZ IM/IM INDEX
-/--
2
SELECT.
TV VCR ENTRÉE
RÉPÉT.
AUDIO AFFICH./
2
VOL ST./AJUST.
39
GB