Using The Timer Programming Feature; Using The Videoplus+/Showview Feature - Samsung SV-5000W Owner's Instructions Manual

Using the Timer Programming Feature

GB
The Timer Programming feature enables you to preset the VCR to
record a programme up to one month before that programme is to
be broadcast. Up to six programmes can be preset.
X REC.SPEED CLK/COUNT PICTURE TIMER
1
STROBE 1 AUDIO
2
3
2
ART INPUT
3
5 6
4
5
❿
STANDARD TIMER
VIDEOPLUS
6
❿ 7
EXIT:(TIMER)
# ❷
8
9
CLOCK: 1/JAN FRI 12:01
10
PR DAY START STOP
❿ ❿❿
--- MO18 14:00 14:30
❿❿
--- ---- --:-- --:-- 11
❿❿
--- ---- --:-- --:--
❿❿
--- ---- --:-- --:--
❿❿
--- ---- --:-- --:--
❿❿
--- ---- --:-- --:--
➛❿
# ❷ 12
DELETE:(CLR/RST) (MENU)
13
INPUT OUTPUT
14
SYSTEM SYSTEM
15
OK
4
16
AUTO MENU 17
18
19
STANDBY/ON
19
INDEX REC.SPEED CLK/COUNT PICTURE
STROBE
2
1 3
26
Before presetting a recording, check that the date and
time are correct.
Insert the cassette and press the TIMER button.
Result: The Timer selection is displayed.
Press to select the standard timer.
Select the required channel by pressing the , buttons or
INPUT to select the SC, AV, L1 or L2 input sources.
Press to select the recording day.
Select the required day by pressing the or buttons.
DLY (daily programme).
W-SU, W-MO, .... , W-SA(weekly programme).
Press to select the recording start time.
Select the required hour value by pressing the or buttons.
Press to select the minutes.
Select the required minute value by pressing the or buttons.
Press to select the recording stop time.
Select the required recording stop time by pressing the or
buttons, following the same procedure as when selecting the
recording start time.
Press to select the REC SYSTEM.
Select the required recording system value by pressing the
or buttons. Offset value is THROUGH.
Press to select the recording speed.
Press the or buttons to switch between the AUTO (Auto Tape
Speed Select), SP (Standard Play), LP (Long Play), SLP (Super
Long Play) recording speeds.
Press to select the VPS or PDC(V/P) recording mode.
Press the or buttons to toggle between the VPS or PDC
mode (marked ON) and the non-VPS/PDC mode (marked -).
When you have finished, press the MENU button.
Press the STANDBY/ON button to activate the timer.
Result: Before starting recording, the VCR compares the timer
duration with the remaining time on the cassette.
Auto Tape Speed Select
The VCR's "Auto Tape Speed Select" function compares
the duration of the timer recording to the actual recording
time remaining on the tape loaded. If there is insufficient
tape to complete a timer recording in AUTO mode, the
VCR automatically switches to LP mode to record the
whole programme.
E.g. If there is a one hour Timer Recording in AUTO
mode to be started, and only 40 minutes tape
remaining, the VCR will record in SP for 20
minutes and switch to complete the remaining 40
minutes in LP mode.

Using the VIDEOPLUS+/SHOWVIEW Feature

Before presetting your VCR:
Switch on both the television and your VCR
Check that the date and time are correct
Insert the cassette on which the programme is to be
recorded (safety tab intact)
1 Press the TIMER button and select VIDEOPLUS+ or SHOWVIEW.
Result: A message is displayed to allow you to enter the
VIDEOPLUS+ or SHOWVIEW code. (Ex.: VIDEOPLUS+)
U.K.: VIDEOPLUS+
Other country: SHOWVIEW
If all six programmes have been set, the message TIMER IS
FULL is displayed. Refer to page 30 if you wish to cancel a
preset recording.
2
Press the numeric buttons to enter the code opposite the pro-
gramme that you wish to record in your television magazine.
If you wish to correct the VIDEOPLUS+/SHOWVIEW code
that you are entering:
Press the button until the digit to be corrected is
cleared
Enter the correct digit
3 Press the MENU button.
Result: The information concerning the programme is displayed.
When using the VIDEOPLUS+/SHOWVIEW function for the
first time with stored stations, the programme number
flashes. This one time, you must enter the station number
manually by pressing the , and buttons. Refer to the
following page if:
The programme number or times flash
You wish to modify the programme
4
If the programme and times are correct, press the OK button.
5
Press the STANDBY/ON button to activate the timer.
6
Refer to page 30 if you wish to:
Check that your VCR has been programmed correctly
Cancel a preset recording
The numbers next to each TV programme listing are
VIDEOPLUS+/SHOWVIEW code numbers, which allow
you to programme your videorecorder instantly with the
remote control. Tap in the VIDEOPLUS+/SHOWVIEW
code for the programme you wish to record.
™ VIDEOPLUS+/SHOWVIEW is a trademark of Gemstar Development Corporation. The
VIDEOPLUS+/SHOWVIEW system is manufactured under licence from Gemstar
Development Corporation.
GB
STANDARD TIMER
❿
VIDEOPLUS
❿ EXIT:(TIMER)
# ❷
VIDEOPLUS
CODE --------
➛
CODE:(0-9) CORRECT:
END:(MENU)
CLOCK: 1/JAN FRI 12:01
PR DAY START STOP
❿ ❿❿
--- MO18 14:00 14:30
❿❿
--- ---- --:-- --:--
❿❿
--- ---- --:-- --:--
❿❿
--- ---- --:-- --:--
❿❿
--- ---- --:-- --:--
❿❿
--- ---- --:-- --:--
➛❿
# ❷
DELETE:(CLR/RST) (MENU)
27