Descaling - Siemens CS858GR.6S Instruction Manual

Cleaning function
en
:
Warning – Risk of burns!
; The appliance will become very hot on the outside
during the cleaning function. Never touch the appliance
door. Allow the appliance to cool down. Keep children
away from the appliance.
Setting the cleaning function
Cleaning lasts 60 minutes.
The duration cannot be changed.
Press the menu button.
1.
The operating modes menu opens.
Select the "Cleaning function" operating mode.
2.
If you touch the "Next" field, information on the
cleaning operation is displayed.
Press the "Start/stop" button to start the cleaning
3.
operation.
You can see the duration counting down in the
status bar.
Keep the kitchen ventilated while cleaning is in
progress.
Once the cleaning has finished
An audible signal sounds. The oven stops heating.
"Finished" appears in the status bar. Use the 0 button
to switch off the audible signal.
Cancelling cleaning
Press the On/Off button. All settings are deleted. You
can implement new settings.
Caution!
The cleaning recommendation is not reset. The
recommendation to run the cleaning function appears
on the display.
You can set the cleaning to run overnight
In the section "Time settings", you can find out how to
delay the end time. This allows you to use the oven at
any time throughout the day. ~ "Time-setting options"
on page 22
Once the cleaning function has ended
Once the cooking compartment has cooled down, wipe
down the cooking compartment with a damp cloth if
necessary.
During operation and while the cleaning function
Note:
is active, reddish patches may form on the surfaces.
This is not rust, but food residues. These patches are
not hazardous to your health and do not limit the
cleaning capacity of the self-cleaning surfaces.
32

Descaling

The appliance must be descaled regularly in order for it
to continue operating correctly.
There are several steps in the descaling programme.
For hygiene reasons, the descaling programme must
be run through completely so that the appliance can be
ready for operation again.In total, the descaling
programme runs for approx. 70-95 minutes.
Descale (approx. 55-70 minutes), then empty and
■
refill the water tank
First rinsing cycle (approx. 9-12 minutes), then
■
empty and refill the water tank
Second rinsing cycle (approx. 9-12 minutes), then
■
empty and dry the water tank
If the descaling process is interrupted (for example, due
to a power failure or because the appliance has been
switched off), you are prompted to rinse the appliance
twice after it is switched back on. The appliance cannot
be used until the second rinsing cycle has come to an
end.
The frequency with which the appliance must be
descaled depends on the hardness of the water used.
When only five more steam-assisted operations are
possible, or fewer, the appliance reminds you to
descale it with a message on the display. The number
of remaining operations is displayed after the appliance
is switched on. You can therefore prepare for the
descaling in good time.
Starting
Caution!
Risk of damage to the appliance: Only use liquid
■
descalers recommended by us for the descaling
programme. The time the product needs to work
during descaling depends on the type of descaler
used. Other descalers may damage the appliance.
Descaler order no. 311 680
Descaling solution: Do not allow any descaling
■
solution or descaler to come into contact with the
control panel or other surfaces on the appliance.
This damages the surfaces. If this does happen,
remove the descaling solution immediately with
water.
If you have used a steam-assisted operation
immediately before descaling, you must first switch the
appliance off so that the residual water is pumped out
of the evaporator system.
Mix 400 ml water with 200 ml liquid descaler to
1.
make a descaling solution.
Press the On/Off button.
2.
Remove the water tank and fill it with descaling
3.
solution.
Once the water tank has been filled with descaling
4.
solution, push it back in again fully.
Close the control panel.
5.
Press the Menu button.
6.
The operating modes menu opens.