RS-232 Serial Interface Connector USB Interface Connector Electrical Characteristics 4. Printer Appearance Switch and LED Functions 5. Paper Loading 6. Set Button Self Test Control Command Summary Electronic Emissions Summary OM5200 Technical Manual Rev. Document No.: 19B00293 Date: March 6, 2018 Page: 2...
1.50ⅹ 3.00 3.00 ⅹ 2.25 Font C 9ⅹ24 1.125ⅹ3.00 1.125ⅹ6.00 2.25 x 6.00 3.00 Space between characters is not included. Measurements in mm. CPL = Characters per line. OM5200 Technical Manual Rev. Document No.: 19B00293 Date: March 6, 2018 Page: 3...
0.2mm (2.84"±0.008")(384dots) and the space on the right and left sides are approximately 5.0 ± 2mm(0.15"±0.079"). a=57.5±0.5mm(2.25"±0.02") b=0.125mm±0.05mm(.056"±.002") c=47mm±0.2mm(1.85±.008") d=5.0±0.2mm(0.20"±0.079") □□□……………□□ e=5.0±0.2mm(0.20"±0.079") [All the numeric values are typical.] < Figure 1.1 Paper Roll Printable Area > OM5200 Technical Manual Rev. Document No.: 19B00293 Date: March 6, 2018 Page: 4...
SG ………………………………… SG NOTES: ◦Set the handshaking so that the transmit data can be received. ◦Transmit data to the printer after turning on the power and initializing the printer. OM5200 Technical Manual Rev. Document No.: 19B00293 Date: March 6, 2018...
Page 8
PARITY < Figure 2.1 Serial transmission bit frame > "1" "0" buffer emptied buffer full "1" "0" ready busy ready busy < Figure 2.2 Line transmission with protocol > OM5200 Technical Manual Rev. Document No.: 19B00293 Date: March 6, 2018 Page: 8...
Data Send Ready System Ground 3.2 USB Connection USB Connector Female Type B -USB Interface SIGNAL DESCRIPTION DATA- Printer transmit data line DATA+ Printer transmit data line System Ground OM5200 Technical Manual Rev. Document No.: 19B00293 Date: March 6, 2018 Page: 9...
8. Tear the excess paper against the serrated edge. 9. To reorder paper, please use part number: TP-58-135. OM5200 Technical Manual Rev. Document No.: 19B00293 Date: March 6, 2018...
6.2 for information. 2. A utility program is used to update the firm-ware. The program is available by calling OMNIPrint customer support. 1-949-833-0080 3. Turn the printer off. 4. Connect the printer to a computer with the utility program loaded and open.
First, make sure the printer is turned off and then while pressing the Paper Feed button turn the printer on. The printer starts printing its factory setting. Example Only OM5200 Technical Manual Rev. Document No.: 19B00293 Date: March 6, 2018...
Select print direction in page mode ESC V Set/cancel 90° cw rotated character ESC W Set printing area in page mode ESC \ Set relative position ESC a Align position OM5200 Technical Manual Rev. Document No.: 19B00293 Date: March 6, 2018 Page: 16...
Page 17
GS h Set bar code height GS k Print bar code GS r Transmit status GS v 0 Print raster bit image GS w Set bar code width OM5200 Technical Manual Rev. Document No.: 19B00293 Date: March 6, 2018 Page: 17...
Example of using the commands. The numbers denoted by <>H is hexadecimal. The numbers denoted by <>B is binary. Print Commands Please see OMNIPrint Printer Control Command Set document for detailed explanation of the command codes. OM5200 Technical Manual Rev.
Consult your authorized reseller or service representative for help. Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. Proper cables and connectors are available from OMNIPRINT INC. authorized dealers. INDUSTRY CANADA CLASS A EMISSION COMPLIANCE STATEMENT This Class A digital apparatus meets all the requirements of the Canadian Interference- Causing Equipment Regulations.
Page 20
Voltage Directive 73/23/EEC and Electromagnetic Compatibility Directive 89/336/ECC on the approximation of the laws of the member states of the EEC Commission. OMNIPRINT INC. cannot accept responsibility for any failure to satisfy the protection requirements resulting from a non-recommended modification of the product.
Need help?
Do you have a question about the OM5200 and is the answer not in the manual?
Questions and answers