Send Lvl To Cho; Multi-Effect Send Level To Chorus; Send Lvl To Rev; Multi-Effect Send Level To Reverb - Roland RS-50 Owner's Manual

Send Lvl to Cho

(Multi-effect send level to chorus)

Sets the amount of the multi-effects sound that is sent to the chorus.
Higher values result in more sound being sent.
Value: 0–127

Send Lvl to Rev

(Multi-effect send level to reverb)

Sets the amount of the multi-effects sound that is sent to the reverb.
Higher values result in more sound being sent.
Value: 0–127
Ctrl 1, 2 (Multi-Effects Control 1, 2)
On the RS-50, certain multi-effect parameters can be assigned to the
modulation lever, knobs, pedal or D Beam. Of the parameters
explained in Multi-effect parameters, the assignable parameters are
marked with a "#" symbol. (Parameters marked with "#1" or "#2"
can be simultaneously controlled using the controller marked with
the same number.) Here you can exchange these assignments, or
choose not to use them. For details, refer to p. 33, p. 89.
Value
OFF: Multi-effect control will not be used.
Items with a "#" symbol: The parameters that can be assigned to
Ctrl1 or Ctrl2. These differ depending on the multi-effect
type.
00: THROUGH
Effects are not applied. Select when creating Patches or Rhythm Sets
that do not use multi-effects.
01: STEREO EQ (Stereo Equalizer)
This is a four-band stereo equalizer (low, mid x 2, high).
fig.MFX-01
L in
4-Band EQ
R in
4-Band EQ
Parameter Value
Low Freq 200, 400 [Hz]
Low Gain -15– +15 [dB]
High Freq 2000, 4000, 8000
[Hz]
High Gain -15– +15 [dB]
Mid1 Freq 200–8000 [Hz]
Mid1 Q 0.5, 1.0, 2.0, 4.0,
8.0
L out
R out
Description
Selects the frequency of the low
range.
Adjusts the gain of the low fre-
quency.
Selects the frequency of the high
range.
Adjusts the gain of the high fre-
quency.
Adjusts the frequency of Middle
1 (mid range).
This parameter adjusts the
width of the area around the
Middle 1 Frequency that will be
affected by the Gain setting.
Higher values of Q will result in
a narrower area being affected.
Parameter Value
Mid1 Gain -15– +15 [dB]
Mid2 Freq 200–8000 [Hz]
Mid2 Q 0.5, 1.0, 2.0, 4.0,
8.0
Mid2 Gain -15– +15 [dB]
Level # 0–127
02: OVERDRIVE
This effect creates a soft distortion similar to that produced by
vacuum tube amplifiers.
fig.MFX-02
L in
Over Amp
drive Simulator
R in
Parameter Value
Drive # 0–127
Pan # L64–63R
Amp Type SMALL,
BUILT-IN,
2-STACK,
3-STACK
Low Gain -15– +15 [dB]
High Gain -15– +15 [dB]
Level 0–127
Adding effects
Description
Adjusts the gain for the area
specified by the Middle 1 Fre-
quency and Q settings.
Adjusts the frequency of Middle
2 (mid range).
This parameter adjusts the
width of the area around the
Middle 2 Frequency that will be
affected by the Gain setting.
Higher values of Q will result in
a narrower area being affected.
Adjusts the gain for the area
specified by the Middle 2 Fre-
quency and Q settings.
Adjusts the output level.
L out
Pan L
2-Band
EQ
Pan R
R out
Description
Adjusts the degree of distortion.
The volume will change togeth-
er with the degree of distortion.
Adjusts the stereo location of the
output sound.
L64 is far left, 0 is center, and
63R is far right.
Selects the type of guitar amp.
SMALL: small amp
BUILT-IN: single-unit type amp
2-STACK: single-unit type amp
3-STACK: large triple stack amp
Adjusts the gain of the low fre-
quency.
Adjusts the gain of the high fre-
quency.
Adjusts the output level.
69