Roland RS-50 Owner's Manual page 77

Parameter Value
HF Damp 200–8000 [Hz],
BYPASS
Balance # D100:0W–
D0:100W
Level 0–127
22: TM CTRL DLY (Time Control Delay)
You can change the delay time in real time. Lengthening the delay
will lower the pitch, and shortening it will raise the pitch.
fig.MFX-22
L in
Balance D
Time Control Delay
Feedback
R in
Balance D
Parameter Value
Delay # 0–840 [ms]
Feedback # -98– +98 [%]
Acceleration 0–15
HF Damp 200–8000 [Hz],
BYPASS
Pan L64–63R
Low Gain -15– +15 [dB]
High Gain -15– +15 [dB]
Description
Adjusts the frequency above
which sound fed back to the ef-
fect will be cut.
If you do not want to cut the
high frequencies of the feed-
back, set this parameter to BY-
PASS.
Adjusts the volume balance be-
tween the direct sound and the
delay sound.
With a setting of D100:0W only the
direct sound will be output, and
with a setting of D0:100W only the
delay sound will be output.
Adjusts the output level.
2-Band
L out
EQ
Balance W
Balance W
2-Band
R out
EQ
Description
Adjusts the time delay from the
direct sound until when each de-
lay sound is heard.
Adjusts the proportion (%) of
the delay sound that is fed back
into the effect.
Negative (-) settings will invert
the phase.
This parameter adjusts the time
over which the Delay Time will
change from the current setting
to a newly specified setting.
The rate of change for the Delay
Time directly affects the rate of
pitch change.
Adjusts the frequency above
which sound fed back to the ef-
fect will be cut.
If you do not want to cut the
high frequencies of the feed-
back, set this parameter to BY-
PASS.
Adjusts the stereo location of the
delay sound.
L64 is far left, 0 is center, and
63R is far right.
Adjusts the gain of the low fre-
quency.
Adjusts the gain of the high fre-
quency.
Parameter Value
Balance D100:0W–
D0:100W
Level 0–127
23: 2V PCH SHIFT (2-Voice Pitch
Shifter)
A Pitch Shifter shifts the pitch of the direct sound. This 2-voice pitch
shifter has two pitch shifters, and can add two pitch shifted sounds
to the direct sound.
fig.MFX-23
L in
Level Balance A
2Voice Pitch Shifter
Level Balance B
R in
Parameter Value
Mode 1, 2, 3, 4, 5
Coarse A #1 -24– +12 [semi]
Coarse B #2 -24– +12 [semi]
Fine A #1 -100– +100
[cent]
Fine B #2 -100– +100
[cent]
Pre Delay A 0–500 [ms]
Pre Delay B 0–500 [ms]
Pan A L64–63R
Pan B L64–63R
Adding effects
Description
Adjusts the volume balance be-
tween the direct sound and the
delay sound.
With a setting of D100:0W only the
direct sound will be output, and
with a setting of D0:100W only the
delay sound will be output.
Adjusts the output level.
Balance D
L out
PanA L
Balance W
PanA R
PanB L
PanB R Balance W
R out
Balance D
Description
Higher settings of this parame-
ter will result in slower re-
sponse, but steadier pitch.
Adjusts the pitch of Pitch Shift A
in semitone steps (-2- +1 oc-
taves).
Adjusts the pitch of Pitch Shift B
in semitone steps (-2- +1 oc-
taves).
Makes fine adjustments to the
pitch of Pitch Shift A in 2-cent
steps (-100- +100 cents).
One cent is 1/100th of a semi-
tone.
Makes fine adjustments to the
pitch of Pitch Shift B in 2-cent
steps (-100- +100 cents).
One cent is 1/100th of a semi-
tone.
Adjusts the time delay from
when the direct sound begins
until the Pitch Shift A sound is
heard.
Adjusts the time delay from
when the direct sound begins
until the Pitch Shift A sound is
heard.
Adjusts the stereo location of the
Pitch Shift A sound.
L64 is far left, 0 is center, and
63R is far right.
Adjusts the stereo location of the
Pitch Shift B sound.
L64 is far left, 0 is center, and
63R is far right.
77