Roland RS-50 Owner's Manual page 80

Adding effects
Parameter Value
Flg Balance # D100:0W–
D0:100W
Level 0–127
29: OD>DELAY (Overdrive
This effect connects an overdrive and a delay in series.
fig.MFX-29
L in
Overdrive
R in
Parameter Value
OD Drive 0–127
OD Pan # L64–63R
Delay Time 0–500 [ms]
Dly Feedback -98– +98 [%]
Dly HF Damp 200–8000 [Hz],
BYPASS
Dly Balance # D100:0W–
D0:100W
Level 0–127
80
Description
Adjusts the volume balance be-
tween the overdrive sound that
is sent through the flanger and
the overdrive sound that is not
sent through the flanger.
With a setting of "D100:0W,"
only the overdrive sound will be
output. With a setting of
"D0:100W," only the overdrive
sound that is sent through the
flanger will be output.
Adjusts the output level.
→
Delay)
L out
Balance D
Balance W
Delay
Balance W
Feedback
R out
Balance D
Description
Adjusts the degree of overdrive
distortion.
The volume will change togeth-
er with the degree of distortion.
Adjusts the stereo location of the
overdrive sound.
L64 is far left, 0 is center, and
63R is far right.
Adjusts the time delay from
when the direct sound begins
until the delay sound is heard.
Adjusts the proportion (%) of
the delay sound that is fed back
into the effect.
Negative (-) settings will invert
the phase.
Adjusts the frequency above
which delayed sound fed back
to the effect will be cut.
If you do not want to cut the
high frequencies of the feed-
back, set this parameter to BY-
PASS.
Adjusts the volume balance be-
tween the overdrive sound that
is sent through the delay and the
overdrive sound that is not sent
through the delay.
With a setting of "D100:0W,"
only the overdrive sound will be
output. With a setting of
"D0:100W," only the overdrive
sound that is sent through the
delay will be output.
Adjusts the output level.
30: DIST>CHORUS
→
(Distortion Chorus)
This effect connects distortion and chorus in series. The parameters
are essentially the same as "27: OD>CHORUS," with the exception
of the following two.
OD Drive→Dist Drive (Specifies the amount of distortion.)
OD Pan→Dist Pan (Specifies the stereo location of the distortion
sound.)
fig.MFX-30
L in
Distortion
R in
31: DIST>FLANGER
→
(Distortion Flanger)
This effect connects distortion and flanger in series. The parameters
are essentially the same as in "28: OD>FLANGER," with the
exception of the following two.
OD Drive→Dist Drive (Specifies the amount of distortion.)
OD Pan→Dist Pan (Specifies the stereo location of the distortion
sound.)
fig.MFX-31
L in
Distortion
R in
32: DIST>DELAY (Distortion
This effect connects distortion and delay in series. The parameters
are essentially the same as in "29: OD>DELAY," with the exception
of the following two.
OD Drive→Dist Drive (Specifies the amount of distortion.)
OD Pan→Dist Pan (Specifies the stereo location of the distortion
sound.)
fig.MFX-32
L in
Distortion
R in
L out
Balance D
Balance W
Chorus
Balance W
R out
Balance D
Balance D
L out
Feedback
Balance W
Flanger
Balance W
R out
Balance D
→
Delay)
L out
Balance D
Balance W
Delay
Balance W
Feedback
R out
Balance D