Roland RS-50 Owner's Manual page 85

Parameter Value
Reset OFF, ON
LEVEL
Low Gain -15– +15 [dB]
High Gain -15– +15 [dB]
Level 0–127
46:TUMBLING DLY (Tumbling Delay)
This is a delay that first produces "tumbling" delayed repeats, and
then echoes the original sound.
It is most effective when applied to single notes of a "one-shot"
sound.
fig.MFX-46
L in
Balance D
Tumbling Delay
Feedback
R in
Balance D
Parameter Value
Type TYPE1–TYPE6
Pre Delay 0–500 [ms]
Delay Time 0–345 [ms]
Level
original tone
A
HF Damp 200–8000 [Hz],
BYPASS
Feedback # -98– +98 [%]
Description
This setting determines whether
the period for the pattern is reset
(ON), or not (OFF) when sounds
are played.
While the rhythm guide is play-
ing, the period for the pattern is
not reset even if you set this ON.
RESET
Adjusts the gain of the low fre-
quency.
Adjusts the gain of the high fre-
quency.
Adjusts the output level.
2-Band
L out
EQ
Balance W
Balance W
2-Band
R out
EQ
Description
Selects one of the six available
types for the number of delay
sounds heard in time "A" in the
diagram below.
Adjusts time "A" in the diagram
below.
Adjusts time "B" in the diagram
below.
B B
Adjusts the frequency above
which sound fed back to the ef-
fect will be cut.
If you do not want to cut the
high frequencies of the feed-
back, set this parameter to BY-
PASS.
Adjusts the proportion (%) of
the delay sound that is fed back
into the effect.
Negative (-) settings will invert
the phase.
Parameter Value
Balance # D100:0W–
D0:100W
Level 0–127
47: FBK RIPPER (Feedback Ripper)
This effect repeatedly cuts the sound, and outputs a delayed sound
for the cut portion. You can create new phrases by applying this to a
drum phrase or other phrase.
fig.MFX-47
L in
Delay
Feedback
Feedback
Delay
R in
Parameter Value
Mod Wave TRI, SQR, SIN,
SAW1/ 2
SAW1
Rate # 0.05–10.00 [Hz],
note *2
Depth # 0–127
Delay Left 0–420 [ms], note
*1
Delay Right 0–420 [ms], note
*1
Dly Feedback -98– +98 [%]
Reset OFF, ON
Level 0–127
Adding effects
Description
Adjusts the volume balance be-
tween the direct sound and the
delay sound.
With a setting of D100:0W only the
direct sound will be output, and
with a setting of D0:100W only the
delay sound will be output.
Adjusts the output level.
2-Band
Ripper L out
EQ
2-Band
Ripper
R out
EQ
Description
TRI: The sound will be cut by a
triangle wave.
SQR: The sound will be cut by a
square wave.
SIN: The sound will be cut by a
sine wave.
SAW1/2: The sound will be cut
by a sawtooth wave. The teeth in
SAW1 and SAW2 point at oppo-
site directions.
SAW2
Adjusts the frequency (speed) of
the change.
Sets the depth to which the ef-
fect is applied.
Adjusts the time from the direct
sound until the left delay sound
is heard.
Adjusts the time from the direct
sound until the right delay
sound is heard.
Adjusts the proportion (%) of
the delay sound that is fed back
into the effect.
Negative (-) settings will invert
the phase.
This setting determines whether
the period for the pattern is reset
(ON), or not (OFF) when sounds
are played.
While the rhythm guide is play-
ing, the period for the pattern is
not reset even if you set this ON.
Adjusts the output level.
85