Roland RS-50 Owner's Manual page 75

Parameter Value
HF Damp 200–8000 [Hz],
BYPASS
Low Gain -15– +15 [dB]
High Gain -15– +15 [dB]
Balance # D100:0W–
D0:100W
Level 0–127
18: LONG DELAY
This is useful when you want to apply a delay that is longer than 17:
St DELAY.
fig.MFX-18
L in
Balance D
Delay
Feedback
R in
Balance D
Parameter Value
Delay 0–840 [ms], note
*1
Feedback # -98– +98 [%]
HF Damp 200–8000 [Hz],
BYPASS
Low Gain -15– +15 [dB]
High Gain -15– +15 [dB]
Balance # D100:0W–
D0:100W
Level 0–127
Description
Adjusts the frequency above
which sound fed back to the ef-
fect will be cut.
If you do not want to cut the
high frequencies of the feed-
back, set this parameter to BY-
PASS.
Adjusts the gain of the low fre-
quency.
Adjusts the gain of the high fre-
quency.
Adjusts the volume balance be-
tween the direct sound and the
delay sound.
With a setting of D100:0W only the
direct sound will be output, and
with a setting of D0:100W only the
delay sound will be output.
Adjusts the output level.
2-Band
L out
EQ
Balance W
Balance W
2-Band
R out
EQ
Description
Adjusts the time from the direct
sound until the delay sound is
heard.
Adjusts the proportion (%) of
the delay sound that is fed back
into the effect.
Negative (-) settings will invert
the phase.
Adjusts the frequency above
which sound fed back to the ef-
fect will be cut.
If you do not want to cut the
high frequencies of the feed-
back, set this parameter to BY-
PASS.
Adjusts the gain of the low fre-
quency.
Adjusts the gain of the high fre-
quency.
Adjusts the volume balance be-
tween the direct sound and the
delay sound.
With a setting of D100:0W only the
direct sound will be output, and
with a setting of D0:100W only the
delay sound will be output.
Adjusts the output level.
19: MOD DELAY (Modulation Delay)
This effect adds modulation to the delayed sound, producing an
effect similar to a flanger.
When Feedback Mode is NORMAL:
fig.MFX-19a
Balance D
L in
Delay
Modulation
Feedback
Feedback
Delay Modulation
R in
Balance D
When Feedback Mode is CROSS:
fig.MFX-19b
Balance D
L in
Delay Modulation
Feedback
Feedback
Delay Modulation
R in
Balance D
Parameter Value
Feedback Mode NORMAL,
CROSS
Delay Left 0–370 [ms]
Delay Right 0–370 [ms]
Feedback -98– +98 [%]
HF Damp 200–8000 [Hz],
BYPASS
Rate # 0.05–10.00 [Hz] Adjusts the speed of the modu-
Depth 0–127
Phase 0–180 [deg]
Adding effects
2-Band
L out
EQ
Balance W
Balance W
2-Band
R out
EQ
2-Band
L out
EQ
Balance W
Balance W
2-Band
R out
EQ
Description
Selects the way in which delay
sound is fed back into the effect.
NORMAL: The left delay sound
will be fed back into the left de-
lay, and the right delay sound
into the right delay.
CROSS: The left delay sound
will be fed back into the right de-
lay, and the right delay sound
into the left delay.
Adjusts the time from the direct
sound until when the left delay
sound is heard.
Adjusts the time from the direct
sound until when the right delay
sound is heard.
Adjusts the proportion (%) of
the delay sound that is fed back
into the effect.
Negative (-) settings will invert
the phase.
Adjusts the frequency above
which sound fed back to the ef-
fect will be cut.
If you do not want to cut the
high frequencies of the feed-
back, set this parameter to BY-
PASS.
lation.
Adjusts the depth of the modu-
lation.
Adjusts the spatial spread of the
sound.
75