Roland RS-50 Owner's Manual page 72

Adding effects
10: LIMITER
The limiter compresses signals that exceed a specified volume level,
preventing distortion from occurring.
fig.MFX-10
L in
Limiter
R in
Parameter Value
Threshold 0–127
Release 0–127
Ratio 1.5:1, 2:1, 4:1,
100:1
Pan # L64–63R
Post Gain 0, +6, +12, +18
[dB]
Low Gain -15– +15 [dB]
High Gain -15– +15 [dB]
Level # 0–127
11: HEXA-CHORUS
Hexa-chorus uses a six-phase chorus (six layers of chorused sound)
to give richness and spatial spread to the sound.
fig.MFX-11
L in
Balance D
Hexa-Chorus
R in
Balance D
Parameter Value
Pre Delay 0.0–100 [ms]
Rate # 0.05–10.00 [Hz] Adjusts the rate of modulation.
Depth 0–127
Pre Delay Dev 0–20
Depth Dev -20– +20
72
L out
Pan L
2-Band
EQ
Pan R
R out
Description
Adjusts the volume at which
compression will begin.
Adjusts the time from when the
volume falls below the Thresh-
old Level until compression is
no longer applied.
Adjusts the compression ratio.
Adjusts the stereo location of the
output sound.L64 is far left, 0 is
center, and 63R is far right.
Adjusts the output gain.
Adjusts the gain of the low fre-
quency.
Adjusts the gain of the high fre-
quency.
Adjusts the output level.
L out
Balance W
Balance W
R out
Description
Adjusts the time delay from
when the direct sound begins
until the chorus sound is heard.
Adjusts the depth of modula-
tion.
Pre Delay Deviation adjusts the
differences in Pre Delay be-
tween each chorus sound.
Pre Delay determines the time
from when the direct sound be-
gins until the processed sound is
heard.
Adjusts the difference in modu-
lation depth between each cho-
rus sound.
Parameter Value
Pan Dev 0–20
Balance # D100:0W–
D0:100W
Level 0–127
12: TREMOLO CHO (Tremolo Chorus)
Tremolo chorus is a chorus effect with added tremolo (cyclic
modulation of volume).
fig.MFX-12
L in
Balance D
Tremolo Chorus
R in
Balance D
Parameter Value
Pre Delay 0.0–100 [ms]
Cho Rate 0.05–10.00 [Hz] Adjusts the modulation speed of
Cho Depth 0–127
Treml Rate # 0.05–10.00 [Hz] Adjusts the modulation speed of
Treml 0–127
Separation
Phase 0–180 [deg]
Balance # D100:0W–
D0:100W
Level 0–127
Description
Adjusts the difference in stereo
location between each chorus
sound.
With a setting of 0, all chorus
sounds will be in the center. With
a setting of 20, each chorus sound
will be spaced at 60 degree inter-
vals relative to the center.
Adjusts the volume balance be-
tween the direct sound and the
chorus sound.
With a setting of D100:0W only the
direct sound will be output, and
with a setting of D0:100W only the
chorus sound will be output.
Adjusts the output level.
L out
Balance W
Balance W
R out
Description
Adjusts the time delay from
when the direct sound begins
until the chorus sound is heard.
the chorus effect.
Adjusts the modulation depth of
the chorus effect.
the tremolo effect.
Adjusts the spread of the tremo-
lo effect.
Adjusts the spread of the tremo-
lo effect.
Adjusts the volume balance be-
tween the direct sound and the
tremolo chorus sound.
With a setting of D100:0W only
the direct sound will be output,
and with a setting of D0:100W
only the tremolo chorus sound
will be output.
Adjusts the output level.