Barco S3-4K Quick Start Manual

M1
MULTIVIEWER (MVR)
MENU
M1: Select MVR Sources -
From the dropdown menus
select the Inputs,
Backgrounds and
Destinations you want to
view and drop them into a
Multiviewer Outputs.
Overlapping is not
allowed. A MVR source
can be used only once. A
maximum total of 64
windows can be used.
M2: Auto Layout Input -
Click on this button to
automatically place all
Inputs into the selected
output.
M3: Adjust Window -
Adjust the size, position
and the color parameters
associate with each
window. Repeat for all
For release 2 only outputs 1 & 2 are active; Clocks will be available in
Inputs and save.
post software release 2.
S2
S1
SETTINGS
MENU
S1: Options - From the
dropdown menu select
the desired language.
Click on the boxes to
select system wide
user preferences such
as Layer positioning.
S2: Tools - Allows
users to perform
Backup and Restore
operations or
download the latest
software from the
Barco website
S3 : Dashboard -
Provides status
information regarding
the cards and other
system diagnostic
information.
M2 M3
S3
- For the latest version of the User's Guide and
the Quick Start Guide, visit www.barco.com.
- Any item contained in this document may
change without notice.
P/N 26-1401004-00 Rev 01
S3-4K – Screen Management System

Quick Start Guide

Visibly yours
PC with Event Master
MVR MVR
1. Ensure that the unit is physically 3. Connect to a computer that has the Event
secured in a rack or is placed on a flat Master control software installed, via an
surface with stable support. If the unit Ethernet cable. A switch is optional if
is installed in a rack, it is mandatory additional devices will be connected.
that the rear brackets are also
installed. 4. Power up the S3-4K, the PC, all monitors
and peripherals.
2. Connect all sources, displays and
peripherals to the S3-4K according to 5. Verify that no errors messages appear on
your event's requirements. If power
the S3-4K front panel.
redundancy is desired, connect power
to both power plugs.
Link Card
1
Dual Redundant Power Supplies
Ethernet
Genlock
Loop
In
1 2 3 4 1 2
S3D In S3D Out
SDI Input & Output Cards
HDMI Output cards (including MVR)
- 4 SDI BNC connectors
- 4 HDMI connectors (top 2 connectors
- SD/HD/3G formats (6G ready)
capable of single link up to 300MHz)
- HDMI 1.4a specification
DisplayPort/HDMI Combo Input Cards
- HDCP 1.4 and EDID 1.3
- 2 DisplayPort and 2 HDMI locking
connectors
DVI Input & Output Cards (optional)
- Displayport 1.1a specification
- 2 DVI-I connectors (no analog signals)
- HDMI 1.4a specification
- Single / Dual Link formats
- HDCP 1.4 & EDID 1.3
- DVI 1.0 specification
- HDCP 1.4 & EDID 1.3
Barco Technical Support:
USA: +1 (866) 374-7878 / EMEA : 0800 90 0410
CHINA : 40088 22726
www.barco.com/support/eSupport.aspx
SEL
PWR
ESC
Control Software
Ethernet switch
6. After the S3-4K boots up, run the Event
Master control software and follow the
sequence of instructions listed in the
Quick Start Guide to complete the system
setup and configuration.
Always refer to the User's Guide for
detailed system specifications,
descriptions and operation instructions.
VPU Cards Input Cards Output Cards
5
2 3 4 6
Link Card
- 2 High speed CXP connectors
Notes:
-Each Input and Output card supports
one 4K/UHD signal
- The cards are NOT hot-swappable
MVR
9
7 8