Panasonic WUME-SF4D-4 Instruction Manual page 145

Common specifications
Type
Model No.
Sensing range (effective)
Minimum sensing object
Effective aperture angle
Supply voltage
Control output
(OSSD 1 / 2)
Operation mode
(Output operation)
Protective circuit
(short circuit protection)
Response time
Auxiliary output
(AUX)
(Non-safety output)
Operation mode
(Output operation)
Protective circuit
(short circuit protection)
Response time
Synchronization method
Interference preven-
tion function
Protective structure
Ambient temperature
Ambient humidity
Ambient illumination
Degree of pollution
Operating altitude
Withstand voltage
Insulation resistance
© Panasonic Industrial Devices SUNX Co., Ltd. 2017
10mm pitch type
SF4D-F□
Short mode: 0.2 to 7m
Long mode: 0.8 to 12m
(selectable by DIP switch)
ø14mm opaque object
±2.5° or less at a sensing range of 3m or longer (based on IEC 61496-2)
+20
24V DC % Ripple P-P 10% or less (excluding voltage drop due to cable)
-30
PNP open-collector transistor / NPN open collector transistor (selectable)
<PNP output selected>
• M aximum source current: 350mA
• Applied voltage: Same as supply voltage
(between control output and +V)
• Residual voltage: 2V or less (source current 350mA)
(excluding voltage drop due to cable)
• Leakage current 0.2mA or less
(including power OFF state)
• M aximum load capacity: 2.2μF
(from no load to maximum output current)
• L oad wiring resistance: 3Ω or less
ON when all beams are received, OFF when one or more beams are blocked
(Also OFF when internal sensor error or synchronization signal error occurs) (Note 1)
OFF response: 10ms or less (not connected in series / parallel), 18ms or less (connected in series / parallel)
(Refer to "<Response time by number of beam channels>")
ON response: 50ms or less (Note 2, 3)
PNP open-collector transistor / NPN open collector transistor (selectable)
<PNP output selected>
• M aximum source current: 60mA
• Applied voltage: Same as supply voltage
(between auxiliary output and +V)
• Residual voltage: 2V or less (source current 60mA)
(excluding voltage drop due to cable)
• Leakage current 0.2mA or less
(including power OFF state)
OSSD ON: OFF, OSSD OFF: ON (Note 1)
OFF response: 60ms or less, ON response: 60ms or less
Line synchronization / optical synchronization (selectable by DIP switch)
Line synchronization: Two units or less (auto)
Optical synchronization:Two units or less (selectable by DIP switch)
• Series connection: 5 units or less (total number of beam channels 256 or less)
• Parallel connection: 3 units or less (total number of beam channels 192 or less)
• Mixed series and parallel connections: Total of 5 units or less
IP67, IP65 (IEC), NEMA Type 13 (NEMA 250)
−10 to +55°C (No condensation or icing), Storage: −25 to +60°C
Incandescent light: 5,000ℓx or less at the light-receiving surface
AC 1,000V for one minute (between all supply terminals connected together and enclosure)
20MΩ or higher using DC 500V megger (between all supply terminals connected
together and enclosure)
20mm pitch type
SF4D-H□
Short mode: 0.2 to 9m, Long mode: 0.8 to 15m
(selectable by DIP switch)
ø25mm opaque object
<NPN output selected>
• M aximum sink current: 350mA
• Applied voltage: Same as supply voltage
• Residual voltage: 2V or less (sink current 350mA)
• Leakage current 0.2mA or less
• M aximum load capacity: 2.2μF
(from no load to maximum output current)
• L oad wiring resistance: 3Ω or less
Incorporated
<NPN output selected>
• M aximum sink current: 60mA
• Applied voltage: Same as supply voltage
• Residual voltage: 2V or less (sink current 60mA)
• Leakage current 0.2mA or less
Incorporated
(total number of beam channels 144 or less)
30 to 85% RH, storage: 30 to 95% RH
3
2,000m or less (Note 4)
Specifications
40mm pitch type
SF4D-A□
ø45mm opaque object
(between control output and 0V)
(excluding voltage drop due to cable)
(including power OFF state)
(between auxiliary output and 0 V)
(excluding voltage drop due to cable)
(including power OFF state)
145