Yamaha 55DEHD Service Manual page 259

Install the control lever and throttle
cam ...................................................... 5-38
Installing the clamp bracket (ET) ........... 7-32
Installing the drive shaft ......................... 6-18
Installing the electrical component ........ 5-36
Installing the lower unit .......................... 6-22
Installing the oil seal housing ................ 6-19
Installing the power unit ......................... 5-38
Installing the propeller shaft housing ..... 6-19
Installing the PTT motor ........................ 7-60
Installing the PTT unit (ET) .................... 7-32
Installing the reservoir ........................... 7-61
Installing the shift rod ............................ 6-18
Installing the starter motor pinion ............8-16
Installing the steering arm ..................... 7-15
Installing the tilt cylinder ........................ 7-59
Installing the tilt ram .............................. 7-61
Installing the trim ram ............................ 7-60
Installing the upper case ....................... 7-17
Installing the water pump ...................... 6-20
Intake manifold ...................................... 5-13
L.
Lower unit ....................................... 3-17, 6-1
Lower unit (55D, 75A models) ...................2-7
Lower unit (85A models)..........................2-12
Lubricating the outboard motor ............. 3-20
Lubricating the throttle gear (EHD) ......... 7-4
M.
Maintenance interval chart ...................... 3-1
Maintenance specification .........................2-5
Manual format........................................... 1-1
Measuring the choke solenoid resistance
(ED, ET) .................................................8-11
Measuring the forward and reverse gear
backlash ............................................... 6-29
Measuring the peak voltage ......................8-1
Model ....................................................... 1-6
P.
Part, lubricant, and sealant ...................... 1-4
Power unit ......................................... 3-3, 5-1
Power unit (55D, 75A models) ...................2-5
Power unit (85A models)..........................2-10
Predelivery check .................................. 1-13
Propeller selection ................................. 1-13
Propeller shaft housing ............................ 6-7
Propeller size ......................................... 1-13
PTT electrical system ............................ 7-64
PTT motor .............................................. 7-41
PTT unit ................................................. 7-35
R.
Removing the clamp bracket
(EHD, ED) ............................................ 7-22
6885J11
Removing the clamp bracket (ET) ......... 7-31
Removing the control lever and throttle
cam ...................................................... 5-12
Removing the crankcase ....................... 5-24
Removing the cylinder head .................. 5-18
Removing the drive shaft ....................... 6-14
Removing the electrical component ...... 5-11
Removing the exhaust cover ................. 5-19
Removing the flywheel magnet ............. 5-11
Removing the lower unit .......................... 6-4
Removing the piston, connecting rod
assembly and crankshaft assembly ..... 5-24
Removing the power unit ......................... 5-9
Removing the propeller shaft housing
assembly ................................................ 6-8
Removing the PTT unit (ET) .................. 7-30
Removing the reed valve assembly ....... 5-14
Removing the shift rod .......................... 6-14
Removing the starter motor pinion ..........8-14
Removing the steering arm ................... 7-15
Removing the water pump ....................... 6-5
S.
Safety while working ................................ 1-4
Selecting the forward gear shim ............ 6-27
Selecting the pinion shim ...................... 6-26
Selecting the reverse gear shim ............ 6-28
Selection ................................................ 1-13
Self-protection .......................................... 1-4
Serial number .......................................... 1-6
Shimming ..................................... 6-25, 6-26
Special service tool ................................. 1-7
Specified torque.......................................2-19
Starboard view ...........................................8-2
Starter motor............................................8-12
Starting system ..........................................8-9
Symbol...................................................... 1-2
Synchronizing the carburetor ................... 3-5
T.
Test run .................................................. 1-17
Tightening torque.....................................2-19
Tiller handle ............................................. 7-1
Tilt cylinder and trim cylinder ................. 7-53
Top cowling .............................................. 3-2
Troubleshooting the lower unit ................. 9-9
Troubleshooting the power unit ................ 9-1
Troubleshooting the PTT unit ................... 9-7
U.
Upper case, steering arm ........................ 7-8
V.
Ventilation ................................................ 1-4
1
2
3
4
5
6
7
8
9
i-3