Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Weller Manuals
  4. Rework stations
  5. WQB 4000SOPS
  6. Quick starter manual

Weller WQB 4000SOPS Quick Starter Manual

Hide thumbs Also See for WQB 4000SOPS:
1
2
3
4
5
6
7
8

Advertisement

Quick Links

Download this manual
WQB 4000SOPS - Quick Starter Guide
1.3
Check the computer system
 System requirements: Pentium 4 / Athlon 64 CPU or newer, CD-ROM, min. 1024
MB RAM,
 Operating system: Windows 2000 SP4, XP SP2, Vista 32-Bit, 7 32Bit & 64Bit
 Screen resolution min.1280 x 1024, min. 16 bit colour depth
 2 free USB 2.0 full powered (500 mA) interfaces
 Graphic card with DirectX 9.29 Support
3.1
Installation of drivers and software
 Important! In order to install the software, you must have Administrator rights.
The device must not be connected.
 To avoid installation conflicts, older drivers should be deinstalled and the
SILABS USB driver should be removed
 Inserted the software CD included in the delivery in the drive. The Installation
Assistant will guide you through the installation. Open the "SOFTWARE" tab.
STEP 1, SILABS USB driver. Follow the instructions
STEP 2, uEye camera driver. Follow the instructions.
From software version 2.17
Opening the "SOFTWARE" tab
To avoid installation conflicts, remove older
versions of the SiLabs USB driver
Choose the right uEye Driver depending on
the version of your operating system (32Bit/64Bit).
It is required, that you have installed the right
Version of the uEye driver, which is delivered
with the WQB 4000 Software.
Version 1.2.6
Page 1 of 8

Advertisement

loading

Related Manuals for Weller WQB 4000SOPS

Summary of Contents for Weller WQB 4000SOPS

  • Page 1 WQB 4000SOPS - Quick Starter Guide From software version 2.17 Check the computer system  System requirements: Pentium 4 / Athlon 64 CPU or newer, CD-ROM, min. 1024 MB RAM,  Operating system: Windows 2000 SP4, XP SP2, Vista 32-Bit, 7 32Bit & 64Bit ...

  • Page 2: Firmware Update

    WQB 4000SOPS - Quick Starter Guide From software version 2.17 STEP 3 DirectX 9.29 Redist Follow the instructions. Install DirectX 9.29 even if a higher version of DirectX (10/11) is installed STEP 4 WQB4000 Software Follow the instructions. Restart your PC after installation Change the Settings of the CPU idle states Start “IDS Camera Manager.exe”...

  • Page 3: Connection Of The Device

    WQB 4000SOPS - Quick Starter Guide From software version 2.17 2.3.1 Assembly of the split optical unit The optical module is already pre-calibrated in the factory. It therefore only needs to be assembled, checked and readjusted as required. 2.3.1.a Assembly: push the linear axis to the right-hand stop.
  • Page 4 WQB 4000SOPS - Quick Starter Guide From software version 2.17 USB ports Important! The WQB 4000SOPS only operates reliably with the shielded USB cables included in the accessories. connect directly with a USB 2.0 - full powered – interface Camera: WQB4000 : connect directly with a USB 2.0 - full powered interface...
  • Page 5 WQB 4000SOPS - Quick Starter Guide From software version 2.17 Check of the split optical unit Placement  In order to calibrate, the Placement tab must be opened and the table must be in Placement position  Insert the calibration template in the PCB holder and activate the frame or cross-hairs ...
  • Page 6 WQB 4000SOPS - Quick Starter Guide From software version 2.17 3.4 Check of the split optical unit Soldering LED illumination  Set the two colours so that they have the same brightness LED illumination  The calibration template becomes red and the component is blue.
  • Page 7 WQB 4000SOPS - Quick Starter Guide From software version 2.17 Loading nozzle parameters or profiles Soldering Load Open Library Run Mode When the software is started, the last profile used is opened up. 1. Loading existing profile  Open desired directory...
  • Page 8 WQB 4000SOPS - Quick Starter Guide From software version 2.17 Loading nozzle parameters or profiles ● Start desoldering ● Desolder component, profile and write ● Clean pc board ● Open tab Placement and insert new component and align manually. Correct the component size if necessary with the height adjustment, define Z-axis stop.