Table of Contents
Advertisement
Precautions for Use
●
Do not insert any foreign object into the machine,
such as a finger, pen, wire, etc.
It could malfunction or result in a fire, electric shock, or injury.
Never put a hand or an object into a cutter section.
●
It can both cause machine damage and personal injury.
●
Use the supplied power cord.
Not using it could result in a fire or electric shock.
●
Obtain power directly from an electrical outlet. Do
not put multiple loads on the electrical outlet.
It could cause a fire.
Do not modify the power cord.
●
Doing so could cause a fire or electric shock.
●
Never place a heavy object on a power cord.
It may damage the cord, resulting in a fire or electric
shock.
●
Do not use a bundled power cord.
The emitted heat may cause a fire or malfunction.
Be sure to unbundle the power cord before use.
●
Do not connect or disconnect a power plug with a
wet hand.
You could receive an electric shock.
●
Do not operate the machine with wet hands or wet clothes.
You could receive an electric shock.
●
Do not place a paper cloth on the machine when it is
connected to an outlet.
Doing so could cause a fire or malfunction.
●
When disconnecting the power plug, hold it directly;
never pull on the power cord.
Pulling on the cord can damage it, resulting in a fire or
electric shock.
●
Install the machine on a flat surface. Do not install in
an unstable location, such as on a wobbly platform
or an inclined surface.
The machine could fall over or fall from the platform and
cause injury or malfunction.
Do not use the machine under direct sunlight, in a
●
hot, humid location, or when there is condensation.
It may cause unstable operation or a malfunction.
●
Do not share an electrical outlet with any device
(air conditioner, refrigerator, microwave, office
automation equipment, etc.) that requires a large
capacity.
It could lower the supply voltage and cause the machine
to malfunction.
●
Do not directly touch the USB connector with your
hands.
Static electricity may cause trouble.
●
Never touch the print head.
Immediately after printing, it is very hot and could burn
you. Also, if the printing head is thumbed, it may cause
trouble.
●
Data saved in a personal computer cannot be saved
permanently.
We cannot be responsible for damage due to loss of
data attributable to trouble or repair, or lost profit.
Disclaimers
MAX will not be held responsible for any damages that occur as a result of not following the instructions in this
manual, damages and lost profits resulting from not being able to use the machine (malfunction), or any relevant
secondary damages.
WARNING
●
Ensure that no water or chemicals are splashed
over the machines.
If water, etc., gets inside for some reason, disconnect the
power plug immediately from the electrical outlet, and
contact your dealer for repair. If the machine is used in
such a state, it could malfunction or result in a fire or
electric shock.
Do not use the machine if it has a symptom of a problem.
●
Such as smoke, abnormal sound, or foul odour.
Using the machine in such a state could result in a fire
or electric shock.
In such a case, immediately disconnect the power
plug from the electrical outlet, and contact your
dealer for repair.
●
Never disassemble or remodel the machine.
It could result in a fire, electric shock, or trouble.
●
Run the machine only on the indicated supply
voltage.
Use of any other voltage could result in a fire or trouble.
● Be sure to ground the machine.
Otherwise, if a short circuit occurs, a fire or electric
shock may result.
● Clean the power plug periodically.
Dust accumulated over a long period could cause a fire
or trouble.
Keep the cutting tool (blade) out of the reach of
●
children.
If swallowed, seek immediate medical attention.
CAUTION
●
When not using the machine for a long time, be sure
to disconnect the power plug from the electrical
outlet for safety.
When moving the machine, be sure to disconnect
●
the power plug from the electrical outlet.
Moving the machine with the power plug connected to
the electrical outlet may damage the plug or cord and
cause a fire or electric shock.
●
When printing or cutting does not function properly
due to jamming of an adhesive tape, ribbon refill, or
foreign object inside the machine, be sure to turn off
the power before eliminating jamming.
Otherwise, you could be injured by abrupt activation of
the machine.
When opening or closing a door cover, be careful
●
not to get a hand, etc., caught.
When moving the machine, be sure to close the door
●
cover and hold the bottom of the body to carry it.
Neglecting this could cause an injury or trouble.
●
When replacing the cutting tool (blade), be sure to
turn off the power.
Otherwise, you could be injured by abrupt activation of
the machine.
Note that the edge of the cutting tool (blade) is very
●
sharp.
Do not touch it. You may be injured.
4
Be Sure to Read These
Hide quick links:
Advertisement
Table of Contents
