Download Print this page

EPSON S5U12517P00C100 User Manual

S1d13517 display controller.
Hide thumbs

Advertisement

S1D13517 Display Controller
S5U13517P00C100
Evaluation Board User
Manual
SEIKO EPSON CORPORATION
Rev. 1.0

Advertisement

   Summary of Contents for EPSON S5U12517P00C100

  • Page 1

    S1D13517 Display Controller S5U13517P00C100 Evaluation Board User Manual SEIKO EPSON CORPORATION Rev. 1.0...

  • Page 2

    No part of this material may be reproduced or duplicated in any form or by any means without the written permission of Seiko Epson. Seiko Epson reserves the right to make changes to this material without notice. Seiko Epson does not assume any lia-...

  • Page 3: Table Of Contents

    4.4.2 Connecting to the Epson S5U13U00P00C100 USB Adapter Board ..14 LCD Panel Interface ......15 GPO and PWM Connections .

  • Page 4

    S1D13517 Display Controller EPSON S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0)

  • Page 5: Chapter 1 Introduction

    S5U13U00P00C100 USB Adapter board so that it can be used with a laptop or desktop computer, via USB 2.0. This user manual is updated as appropriate. Please check the Epson Research and Development Website at www.erd.epson.com for the latest revision of this document before beginning any development.

  • Page 6: Chapter 2 Features

    • 14-pin DIP socket (if a clock other than 24MHz must be used) • 3.3V input power • On-board voltage regulator with 2.5V output • On-board voltage regulator with adjustable 6~24V output, 40mA max., to provide power for LED backlight of LCD panels. EPSON S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0)

  • Page 7: Chapter 3 Installation And Configuration

    = Required settings when using S5U13U00P00C100 USB Adapter board The following figure shows the location of DIP switch SW1 on the S5U13517P00C100 board. DIP Switch Figure 3-1: Configuration DIP Switch (SW1) Location S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON...

  • Page 8: Configuration Jumpers

    1 and 2 of the jumper. The jumper associated with each power supply is as follows: J1 for COREVDD J2 for IOVDD J3 for PLLVDD J2, J1 Figure 3-2: Configuration Jumper Locations (J1, J2, J3) EPSON S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0)

  • Page 9

    When the jumper is at position 3-4, the second oscillator is selected. When the jumper is at position 5-6, the CLKI pin is forced to GND. Figure 3-3: Configuration Jumper Location (J4, J5, J6) S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON...

  • Page 10: Chapter 4 Technical Description

    IOVDD can be in the range of 3.0~3.6V. When J4 is set to the 1-2 position, IOVDD is connected to 3.3V. If a different voltage is required for IOVDD, set JP4 to the 2-3 position and connect the external power supply to pin 32 of connector CN1. EPSON S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0)

  • Page 11: Clocks

    The S1D13517 Display Controller on the S5U13517P00C100 evaluation board can be reset using a push-button (SW2), or via an active low reset signal from the host development platform (pin 33 on the CN1 connector). Figure 4-1: Second oscillator and Reset switch Location (Y2, SW2) S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON...

  • Page 12: Host Interface

    The following figure shows the location of host bus connector CN1. CN1 is a 0.1x0.1 inch 34-pin header (17x2). Figure 4-2: Host Bus Connector Location (CN1) For the pinout of connector CN1, see Chapter 6, “Schematic Diagrams” on page 18. EPSON S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0)

  • Page 13: Connecting To The Epson S5u13u00p00c100 Usb Adapter Board

    For the pinout of connectors P1 and P2, see Chapter 6, “Schematic Diagrams” on page 18. Note A windows driver must be installed on the PC when the S5U13517P00C100 is used with the S5U13U00P00C100 USB Adapter Board. The S1D13xxxUSB driver is available at www.erd.epson.com. S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON...

  • Page 14: Lcd Panel Interface

    CCFL backlight. Usually, the inverter current consumption is higher than the maximum 40mA current available from the on-board voltage regulator. The following diagram shows the location of the LCD panel connectors CN3 and CN5. Figure 4-4: LCD Panel Connectors Location (CN3, CN5) EPSON S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0)

  • Page 15: Gpo And Pwm Connections

    The following figure shows the location of the GPO and PWM connector, CN4. Figure 4-5: GPIO and PWM Connector Location (CN4) For the pinout of connector CN4, see Chapter 6, “Schematic Diagrams” on page 18. S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON...

  • Page 16: Chapter 5 Parts Lists

    C14,C16,C18,C20,C22, C24,C26,C29,C33,C38, 0.01u C44,C46,C48,C50,C52, C54,C56 2000p 100u 47u 10v 1u 50V SML-310VT SML-310DT SML-310PT MBR0530 F1,F2 ACF451832-222 J1,J2,J3,J5 WL-1-2P WL-1-3P WLW-3 L1,L2 BLM21P LQH32CN100K23L PAD1,PAD2,PAD3 2mm diameter P1,P2 PRPN202PAEN-RC 3k 1% R2,R3,R4 EPSON S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0)

  • Page 17

    R33,R34,R35,R36,R37, R38,R39,R40,R41,R42, R43,R44,R45,R46,R47, R48,R49,R50,R51,R52, R53,R54,R55,R56,R57, R58,R59,R60 150k R13,R17 33 1% R18,R19,R20 887k SH1,SH2,SH3,SH4,SH5, .100 in. Jumper Shunt CFS-0400MB SKRKAEE010 TP1,TP2,TP3,TP4,TP5, HK-2-S TP6,TP7,TP8,TP9,TP10 S1D13517 TPS76915DBVT IS42S16800E (128Mbit SDRAM) TPS61040 200k SG-210 24MHz XR2A-1405 S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON...

  • Page 18: Chapter 6 Schematic Diagrams

    S1D13517 Display Controller Chapter 6 Schematic Diagrams Figure 6-1: S5U13517P00C100 Schematic Diagram (1 of 3) EPSON S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0)

  • Page 19

    S1D13517 Display Controller Figure 6-2: S5U13517P00C100 Schematic Diagram (2 of 3) S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0) EPSON...

  • Page 20

    S1D13517 Display Controller Figure 6-3: S5U13517P00C100 Schematic Diagram (3 of 3) EPSON S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0)

  • Page 21: Chapter 8 References

    7.1 Documents • Epson Research and Development, Inc., S1D13517 Hardware Functional Specification, document number X92A-A-001-xx • Epson Research and Development, Inc., S5U13U00P00C100 USB Adapter Board User Manual, document number I00Z-G-018-xx 7.2 Document Sources • Epson Research and Development Website: http://www.erd.epson.com S5U13517P00C100 Evaluation Board User Manual (Rev.

  • Page 22

    S1D13517 Display Controller Change Record X92A-G-001-01 Revision 1.0 - Issued: May 8, 2009 • initial release EPSON S5U13517P00C100 Evaluation Board User Manual (Rev. 1.0)

  • Page 23

    20/F, Harbour Centre, 25 Harbour Road Wanchai, Hong Kong Phone: +852-2585-4600 FAX: +852-2827-4346 Telex: 65542 EPSCO HX EPSON TAIWAN TECHNOLOGY & TRADING LTD. 14F, No. 7, Song Ren Road, Taipei 110, TAIWAN Phone: +886-2-8786-6688 FAX: +886-2-8786-6660 EPSON SINGAPORE PTE., LTD.

  • Page 24

    Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Epson S5U13517P00C100...

Comments to this Manuals

Symbols: 0
Latest comments: