Cisco 2800 Series Manual page 210

How to Use the ROM Monitor—Typical Tasks
Image text-base: 0x40098478, data-base: 0x41520000
Port Statistics for unclassified packets is not turned on.
Cisco Router (revision 48.46) with 251904K/10240K bytes of memory.
Processor board ID
2 Gigabit Ethernet interfaces
2 Serial(sync/async) interfaces
2 Channelized T1/PRI ports
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
253160K bytes of USB Flash usbflash1 (Read/Write)
127104K bytes of ATA CompactFlash (Read/Write)
Press RETURN to get started!
*Sep 23 16:19:56.611: %USB_HOST_STACK-6-USB_DEVICE_CONNECTED: A Full speed USB device has
been inserted in port 1.
*Sep 23 16:19:57.015: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to up
*Sep 23 16:19:57.391: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to up
*Sep 23 16:19:57.951: %LINK-3-UPDOWN: Interface Serial0/3/0, changed state to down
*Sep 23 16:19:57.955: %LINK-3-UPDOWN: Interface Serial0/3/1, changed state to down
*Sep 23 16:19:57.963: %USBFLASH-5-CHANGE: usbflash1 has been inserted!
*Sep 23 16:19:58.015: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0,
changed state to up
*Sep 23 16:19:58.391: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1,
changed state to down
*Sep 23 16:19:58.951: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0, changed
state to down
*Sep 23 16:19:58.955: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/1, changed
state to down
*Sep 23 16:20:00.139: %SYS-5-CONFIG_I: Configured from memory by console
*Sep 23 16:20:00.351: %SYS-5-RESTART: System restarted --
Cisco IOS Software, 2800 Software (C2800NM-IPBASE-M), Version 12.4(3), RELEASE SOFTWARE
(fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Fri 22-Jul-05 11:37 by hqluong
*Sep 23 16:20:00.355: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold
start
*Sep 23 16:20:00.567: %SYS-6-BOOTTIME: Time taken to reboot after reload =
*Sep 23 16:20:00.763: %CONTROLLER-5-UPDOWN: Controller T1 0/2/0, changed state to down
(LOS detected)
*Sep 23 16:20:00.763: %CONTROLLER-5-UPDOWN: Controller T1 0/2/1, changed state to down
(LOS detected)
*Sep 23 16:20:02.083: %LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to
administratively down
*Sep 23 16:20:02.091: %LINK-5-CHANGED: Interface Serial0/3/0, changed state to
administratively down
*Sep 23 16:20:02.103: %LINK-5-CHANGED: Interface Serial0/3/1, changed state to
administratively down
Router>
What to Do Next
If you want to configure the router to load a specified image at the next system reload or power-cycle,
see the following documents:
•
•
Using the ROM Monitor
14
"Booting Commands" chapter of the Cisco IOS Configuration Fundamentals Command Reference
Cisco IOS Configuration Fundamentals and Network Management Configuration Guide
87 seconds
OL-5997-02