Table of Contents
Advertisement
Test set options
One of the following test set options must be selected.
Standard configuration (Option 700)
– The standard configuration is the basic test set configuration,
which does not include signal conditioning devices such as
amplifiers.
Add amplifiers for improved dynamic range (Option 001)
– Option 001 adds an amplifier between each test port coupler
and the receiver switch to improved system dynamic range. It
is primarily offered for the test set with solid-state switches
to compensate for the insertion loss.
Add amplifiers and bias-tees (Option 002)
– Option 002 adds an amplifier between each test port coupler
and the receiver switch to improved system dynamic range
and bias-tees for all test ports on the test set as well as the
analyzer. It is primarily offered for the test set with solid-state
switches to compensate for the insertion loss.
Interface kits
The interface kit includes a set of semi-rigid RF jumper cables and
two pairs of rear locking feet that connect and lock the analyzer
and the test set together. When ordering a multiport test set, the
analyzer that is used with the test set must be specified to add
one of the following interface kits. The availability depends on
the test set model. There are following three interface kit models
based on the jumper connector layouts on the test set. Therefore,
only one interface kit model ("PX", "PN", or "PL") is available
on each test set. Each interface kit model has one digit suffix
indicating the connector type; 1 for 1.85 mm, 2 for 2.4 mm and 3
for 3.5 mm (or SMA).
U3021PXx
Interface kit for test set with jumper connectors to align with N524xA PNA-X and N522xA PNA
U3021PNx
Interface kit for test set with jumper connectors to align with E836xB/C PNA and N5230A/C-x25 2-port PNA-L
Option 261
For use with E8361A/C 2-port PNA
Option 262
For use with E8362B/C 2-port PNA or N5230A/C-225 2-port PNA-L
Option 263
For use with E8363B/3C/4B/4C 2-port PNA or N5230A/C-425/525 2-port PNA-L
Option 430
For use with N5230A/C-245/246 4-port PNA-L
Option 242
For use with N5241/42/49A-2xx 2-port PNA-X or N5221A/2A-2xx 2-port PNA
Option 442
For use with N5241/42/49A-400 4-port PNA-X or N5221A/2A-4xx 4-port PNA
Option 245
For use with N5244A/5A-200 2-port PNA-X or N5224A/5A-2xx 2-port PNA
Option 445
For use with N5244A/5A-400 4-port PNA-X or N5224A/5A-4xx 4-port PNA
Option 247
For use with N5247A-200 2-port PNA-X or N5227A-2xx 2-port PNA
Option 447
For use with N5247A-400 4-port PNA-X or N5227A-4xx 4-port PNA
When ordering an additional cable set, a spare cable or rear locking feet, refer to the multiport test set user's guide or go to:
www.keysight.com/find/multiport
Find us at www.keysight.com
Millimeter-wave measurements
Single sweep solution to 110 GHz
The 67 GHz PNA and PNA-X network analyzers allow extending
the maximum frequency to 110 GHz with a 1.0 mm coaxial con-
nector, enabling 10 MHz to 110 GHz single sweep measurements
using a millimeter-wave controller and frequency extenders with
built-in combiner.
The 10 MHz to 110 GHz broadband millimeter-wave system pro-
vides high performance and capabilities including power control,
4-port true-differential, and frequency converter measurements.
It is configured with an N5227A PNA with Option 201 (2-ports)
or Option 401 (4-ports), or N5247A with Option 200 (2-ports) or
Option 400 (4-ports), Option 020 IF access, an N5261A 2-port
or an N5262A 4-port millimeter-wave test set controller with
1.85 mm coaxial cables (Option 112 for N5261A, Option 114 for
N5262A) and RF/LO/IF/DC cables sets (to select the cable length
and quantities), and one (for 2-ports) or two (for 4-ports) each of
right and left frequency extenders with required attenuators and
bias-tee configurations.
Waveguide banded solutions to 1.05 THz
The waveguide banded millimeter-wave solution covers wave-
guide bands from 50 GHz to 1.05 THz. A 2- or 4-port PNA or
PNA-X in conjunction with N5261A (for 2-port) or N5262A
(for 4-port) configures for the most complete millimeter wave
solution. It is configured with a PNA Series with Option 020 IF
access, configurable test set (Option 201 or 401), and frequency
offset mode (Option 080), or PNA-X Series with 2-port (Option
200) or 4-port (Option 400) and IF access (Option 020). For the
millimeter-wave test controller, appropriate RF cable option and
RF/LO/IF/DC cable set option for frequency extenders must be
selected for the analyzer's connector type, number of test ports,
and lengths. Add appropriate frequency extenders with required
quantity for the measurements.
For complete list of millimeter-wave products and options, and
ordering instructions, please refer to 5989-7620EN Millimeter-
wave Network Analyzers Technical Overview
Page 26
Hide quick links:
Advertisement
Table of Contents
