Panasonic SF4B-F31G(V2) Instruction Manual page 83

Common specifications
Type
Model No.
Detecting capability
(Min. sensing object)
Effective aperture
angle (EAA)
Supply voltage
Control output
(OSSD 1 / 2)
Operation mode
(Output operation)
Protection circuit
(Short-circuit)
Response time
Auxiliary output
(Non-safety output)
Operation mode
(Output operation)
Protection circuit
(Short-circuit)
Protection
Degree of pollution
Ambient temperature
Ambient humidity
Ambient illuminance
Altitude for use
Voltage withstandability
Insulation resistance 20MΩ or more with 500V DC mega (between all supply terminals connected together and enclosure)
Vibration resistance
Shock resistance
SFF (Safe failure fraction)
HFT (Hardware
failure tolerance)
Sub system type
Mission time
Emitting element
Connection method
Cable extension
Material
Accessory
Applicable standard
© Panasonic Industrial Devices SUNX Co., Ltd. 2017
10mm pitch type
SF4B-F□G<V2>
ø14mm opaque object
±2.5 degree or less [for sensing range exceeding 3m (Required by IEC 61496-2, ANSI/UL 61496-2)]
PNP open-collector / NPN open-collector transistor (switching type)
<For PNP output>
• Maximum source current: 200mA
• Applied voltage: Same as supply voltage
(between the control output and +V)
• Residual voltage: 2.5V or less
(source current 200mA, when using 20m length cable)
• Leakage current: 0.1mA or less
(Including power supply OFF condition)
• Maximum load capacity: 0.22µF
(No load to maximum output current)
• Load wiring resistance: 3Ω or less
ON when all beams are received, OFF when one or more beams are interrupted (Note 1, 2)
(OFF when fault occurs in the sensor to the synchronization single error, too)
In normal operation...OFF response: 14ms or less, ON response: 80 to 90ms
PNP open-collector transistor / NPN open-collector transistor (switching type)
<For PNP output>
• Maximum source current: 60mA
• Applied voltage: Same as supply voltage
(between the auxiliary output and +V)
• Residual voltage: 2.5V or less
(source current 60mA, when using 20m length cable)
When OSSDs are ON: OFF, when OSSDs are OFF: ON (factory setting)
[Changeable by using the handy controller (SFB-HC) (optional).]
-10 to +55°C(No dew condensation ot icing allowed), Storage:-25 to +70°C
Incadescent lamp: 3,500 ℓ x or less at the light-receiving surface
1,000V AC for one min. (between all supply terminals connected together and enclosure)
10 to 55Hz frequency, 0.75mm amplitude in X, Y, and Z directions for two hours each
2
300m/s acceleration (Approx. 30G) in X, Y and Z directions for three times each
Infrared LED (Peak emission wavelength: 870nm)
Extension up to total 50m is possible for both emitter and receiver connecting cable (optional) (Note 4)
Enclosure: Aluminum, Upper / lower case: Aluminum, Sensing surface: PC / Polyester resin, Cap: PBT
MS-SFB-2 (Intermediate sup-
porting bracket): (Note 5)
SF4B-TR14 (Test rod): 1 pc.
EN 61496-1 (Type 4), EN 55011, EN 61000-6-2, EN 50178, EN ISO 13849-1: 2008 (Category 4,PLe)
IEC 61496-1/2 (Type 4) ISO 13849-1: 2006 (Category 4, PLe), IEC 61508-1 to 7 (SIL3)
JIS B 9704-1/2 (Type 4), JIS B 9705-1 (Category 4), JIS C 0508 (SIL3)
ANSI/UL 61496-1/2 (Type 4), UL 1998 (Class 2)
20mm pitch type
SF4B-H□G<V2>
ø25mm opaque object
24V DC ± 10 % Ripple P-P10% or less
<For NPN output>
• Maximum sink current: 200mA
• Applied voltage: Same as supply voltage
• Residual voltage: 2.5V or less
(sink current 200mA, when using 20m length cable)
• Leakage current: 0.1mA or less
• Maximum load capacity: 0.22µF
• Load wiring resistance: 3Ω or less
Incorporated
<For NPN output>
• Maximum sink current: 60mA
• Applied voltage: Same as supply voltage
• Residual voltage: 2.5V or less
(sink current 60mA, when using 20m length cable)
Incorporated
IP65 and IP67(IEC)
3
30 to 85%RH, Strage: 30 to 95%RH
2000m or less above sea level (Note 3)
99%
1
Type B (IEC 61508-2)
20 years
Connection with connectors
MS-SFB-2 (Intermediate sup-
porting bracket): (Note 5)
SF4B-TR25 (Test rod): 1
40mm pitch type
SF4B-A□G<V2>
ø45mm opaque object
(between the control output and 0V)
(Including power supply OFF condition)
(No load to maximum output current)
(between the auxiliary output and 0V)
MS-SFB-2 (Intermediate
supporting bracket): (Note 5)
83