Jumper Settings & Connector Pinouts - Lanner FW-8759 User Manual

Jumper Settings & Connector Pinouts
Fan Connectors(FAN1/FAN2/FAN3): The 5-pin
connector is for connecting the CPU and system
fans. It comes with the smart fan feature by which
the fans could be monitored and turned on when
the temperature exceed the set threshold.
Pin No. 1
Function CPUFANOUTPWM_1
DIMM Socket (DIMM1/DIMM2): The 240-pin DDR3
DIMM is for connecting the DDR3/DDR3L 1600 MHz.
The system can support up to 8 GB in maximum. A
DDR3 module has the same physical dimensions as a
DDR2 DIMM but the notch on the pins is positioned
differently.
Note: Since the system is capable of dual
channel architecture, both DIMMs have to be
populated to enable dual channel mode.
SATA 1, 2 and 3 Connectors (SATA1/SATA2/
SATA3): It is for connecting a SATA harddisk to
be served as your system's storage. The system can
accommodate 2 disks (2.5") in maximum. SATA
1 complies fully with SATA Revision 3.0 standard
with data transfer rates of up to 6.0 Gb/s; SATA 2,
3 comply with SATA Revision 2.0 standard. The
controller contains two modes of operation—a
legacy mode using I/O space, and an AHCI mode
using memory space. Software that uses legacy
mode will not have AHCI capabilities.
You will need to configure your disk to one of the
3 modes of SATA configuration, i.e., IDE, RAID,
and AHCI in the BIOS.
5
4
3
2
1
2 3 4
NC CPUFANIN P12V
Note:
To configure your Hard disk using the
1.
integrated RAID feature, the Intel®Rapid
Storage Technology Utility has to be installed
on your Operating System.
You will need to select the RAID mode in the
2.
BIOS for your SATA drives first. There is also a
Intel® RSTe OpROM utility for creating RAID
volume; to enter the RSTe OpROM, press Ctrl-I
during POST.
For operating systems other than Microsoft
3.
Windows Vista and Windows® 7, it is
required to pre-install the Intel Rapid Storage
Technology driver during the F6 installation of
5
Windows setup ("press F6 if you need to install
a third party SCSI or RAID driver.... " ).
GND
Visit the Intel support page at http://www.intel.
com/p/en_US/support/highlights/chpsts/imsm
for more information and download links.
The Intel controller hubs are also supported
4.
by Linux. Beginning with Linux kernel
version 2.6.27, the mdadm utility 3.0
supports RAID 0, RAID 1, RAID 5, and RAID
10. To use the RAID features in dmraid and
mdadm, you will need to set up the RAID
volume using the Intel® Matrix Storage
Manager option ROM (click CTRL + I when
prompted during boot to enter the option
ROM user interface).
SATA1/SATA2/SATA3: supports SATA 3.0/SATA2.0/ SATA
2.0 connection respectively
7
6
5
1
SATA2, SATA3
SATA HDD Power Connector (CON1/CON2):
CON1
4 3 2 1
CON2
1 2 3 4
6Pin No.
1
2
SATA1
3
4
5
6
7
6Pin No. Function
1 +12V
2 GND
3 GND
4 +5V
®
Function
GND
TX+
TX-
GND
RX-
RX+
GND