1. Manuals
  2. Brands
  3. Aeotec Manuals
  4. Switch
  5. Dual Nano Switch ZW132
  6. Manual

Aeotec ZW132 Manual

Dual nano series z-wave switch
Hide thumbs Also See for ZW132:
Table of Contents

Advertisement

Quick Links

See also: User Manual
Dual Nano Switch
View the expanded manual:
http://aeotec.com/support
IMPORTANT!
This product has been fully tested and certified to
work with Z-Wave by the Z-Wave Alliance. It is
crafted using Z-Wave Plus, the latest device version
of Z-Wave. As such, if the product does not work
with your gateway, please be sure to check with your
gateway manufacturer that they have integrated this
device with their gateway for full operation.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ZW132 and is the answer not in the manual?

Questions and answers

Related Manuals for Aeotec ZW132

Summary of Contents for Aeotec ZW132

  • Page 1 Dual Nano Switch View the expanded manual: http://aeotec.com/support IMPORTANT! This product has been fully tested and certified to work with Z-Wave by the Z-Wave Alliance. It is crafted using Z-Wave Plus, the latest device version of Z-Wave. As such, if the product does not work...
  • Page 3 Contact your local government for information regarding the collection systems available. Switch. Certifications (regional): Aeotec Dual Nano Switch is a low-cost Z-Wave Switch specifically used to enable Z-Wave command Z-Wave and Z-Wave Plus are registered trademarks of Sigma and control (on/off) of any wall switches. It can report...
  • Page 4 Familiarize yourself with your Dual Connect the equipment into an outlet on a circuit different from that to which the receiver Nano Switch. is connected. Consul the dealer or an experienced radio/TV technician for help. RF antenna UL NOTICE (For USA). Touch panel connection port Install only in a UL listed junction box sized RGB LED...
  • Page 5 found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference IN OUT1 OUT2 S1...
  • Page 6 FCC NOTICE (for USA) Install the Dual Nano Switch. Important: A licensed electrician with knowledge THE MANUFACTURER IS NOT RESPONSIBLE and understanding electrician systems and electrical FOR ANY RADIO OR TV INTERFERENCE CAUSED safety should complete the electrical installation. BY UNAUTHORIZED MODIFICATIONS TO THIS 1.
  • Page 7 Preparing connection wires USE OF THE PRODUCTS, WHETHER BASED 14 AWG power wires for Input/ Output. ON NEGLIGENCE, STRICT LIABILITY, BREACH 18 AWG copper wires for external manual switch. OF WARRANTY, BREACH OF AGREEMENT, OR Use the wire stripper cut the metallic part of the EQUITABLE PRINCIPLES, IS EXPRESSLY LIMITED connection wire and make sure the length of the TO, AT AEON LABS' OPTION, REPLACEMENT...
  • Page 8 Wiring diagram of AC120V/230V power input. or relating to any actual or alleged infringement or misappropriation of any patent, trademark, mask work, copyright, trade secret or any actual or alleged violation of any other intellectual property rights arising from or in connection with the products, except to the extent that such infringement exists as a result of Aeon Labs' manufacturing processes.
  • Page 9 needs, Company must prepay shipping and In some cases, you may have some loads just only transportation charges for returned Products, and can be used on the voltage of DC24V and hope that insure the shipment or accept the risk of loss or it still can be controlled by the Dual Nano Switch, so damage during such shipment and transportation.
  • Page 10 Wiring diagram of DC24V power input. Any repairs under this warranty must be conducted by an authorized Aeon Labs service representative Since the Dual Nano Switch also supports the and under Aeon Labs' RMA policy. Any repairs DC24V power input, so you can use it to control the conducted by unauthorized persons shall void this loads that powered by DC24V.
  • Page 11 If the output loads should be only powered by Aeon Labs warrants to the original purchaser of AC120V or AC230V, you can change the wire Products, that is the Company who you have connection as below: purchased from, that for the Warranty Period (as defined below), the Products will be free from material defects in materials and workmanship.

  • Page 12: Warranty

    Switch uses the SPDT (Single-Pole Double-Throw) subsequent to your products’ warranty, please get in switches as the external manual switch for 3-Way touch with our support team via http://aeotec.com/ connection. support. The Company you bought this product Wiring diagram of 3-Way connection for the from has also guaranteed to assist you with any of external manual switch.

  • Page 13: Technical Specifications

    (SPDT) confirmation. 6 Technical specifications. Live AC120V~230V Model number: ZW132/ZW140 Neutral Power input: 120VAC to 240VAC, 50Hz to 60Hz. Install Dual Nano Switch to the gang box. Rated output: 6.5A per channel for resistive load. Live/Hot wire connection: Connect the Live/ Total current: Max 10A.
  • Page 14 Neutral wire connection: Connect the Neutral solid indication. If inclusion is unsuccessful, the red wire to the “N” terminal on the Dual Nano LED will be on for 2 seconds and then return to a Switch. colourful gradient. Load wire connection: Connect the 2 Load Including Dual Nano Switch as a secure device: wires to the “OUT1”...
  • Page 15 Position the antenna towards the back of the not have the ability to monitor energy consumption. box, away from all other wiring. The model ZW132 Dual Nano Switch supports the Reinstall the Dual Nano Switch to the gang energy metering feature and you can see the words box.
  • Page 16 Restore Power. Restore power at the circuit breaker or fuse. Monitoring Energy Consumption. The Aeotec Dual Nano Switch can report wattage energy usage or kWh energy usage to a Z-Wave control point when requested. If this function is supported by the control points, the energy consumption will be displayed in the user interface of the control points.

  • Page 17: Quick Start

    Quick start. manual switch wired into Dual Nano Switch, toggle the button on the manual switch once and wait 2 Adding your Dual Nano Switch to a Z-Wave seconds for the Dual Nano Switch to detect the type of manual switch. network.

  • Page 18: Advanced Functions

    If the Dual Nano Switch has been successfully controller instruction manual. added to your Z-Wave network, its RGB LED will Set your Z-Wave controller into removal mode. be solid. If the pairing was unsuccessful, the red Press the Action Button on the Dual Nano Switch LED will be on for 2 seconds and then remain a or toggle the external manual switch 3 times in colourful gradient, repeat the instructions above...

  • Page 19: Association Information

    Association information...
  • Page 20 Configuration parameters information...

This manual is also suitable for:

Zw140

Table of Contents