Calibration - ABB 6X1EH Operating Instructions Manual

CALIBRATION

Unlike conventional electronic transmitters, the use of a
microprocessor and the presence of serial communications
between the transmitter and the configuration device, allows the
use of several different approaches in calibration and servicing.
Different methods can be used to calibrate the Smart transmitter:
i) using the optional zero and span calibration screws in
the transmitter secondary unit.
ii) using zero/span raise/lower on transmitter electronics
links.
iii) using the Hand Held Communicator.
iv) using the Personal Computer Configuration Software
Package.
This chapter describes the first method; the others are
described next or in the relevant Instruction Manuals of
configuration tools. If the optional calibration screws are
not fitted calibration must be done by method iii) or iv).
In the addendum (use of hardware links on the secondary
electronics) there is an explanation of the raise/lower operation
for ZERO and SPAN. In the Analog + HART version it is also
possible to apply a scaling to the reading of the transmitter.
The operation is called PV-scaling and is used to align the
"zero" of the process with the "zero" reading of the transmitter.
See the description in the Addendum for PV scaling operation.
Note: Unless otherwise specified the instrument is
factory calibrated at maximum span with the LRV set to true
zero. Instruments adjusted and tagged for a specific range
will not require recalibration. Rezeroing of the transmitter
may be required in order to compensate for zero shift
arising from the installation.
Preliminary operation
Before commencing calibration ensure that:
i) the required span, the upper and lower range value (URV &
LRV) are within the span and range limits (URL & LRL)
indicated on the nameplate (please refer to "Range and
Span" consideration on the previous page).
ii) the transmitter is properly powered and the electrical
connections correctly made.
iii) the write protect link, located on the electronics module is in
position OFF (write allowed). Access to the link is gained by
unscrewing the secondary unit housing cover at the opposite
end to the terminal cover (See Fig. 9).
Upscale/Downscale
Write/Write
link
Protect link
ON
OFF
Raise/Lower
Fig. 9 Location of the links on the electronics
and on the integral digital display
- 12 -
Damping
Raise/Lower
C D
B
A
Span
iv) the Upscale/Downscale link is positioned to the required
function: ON for Downscale OFF for Upscale (see Fig. 9).
v) make the electrical connections, as indicated in Fig. 10.
Connect a precision milliammeter as shown and remove the
short circuit link.
Fig. 10 - Calibration electrical connections
Set up an appropriate test rig in accordance with the required
calibration. Figure 11 shows a complete test rig that can be
selectively used to suit the calibration.
V.G. - Vacuum Gauge
V.P. - Vacuum Pump
L
C
M1/M2 - Pressure gauge
M2
Pressure Generator or
Dead Weight Calibrator
Fig. 11 - Calibration pressure connections
Note that calibration accuracy is strictly related to the accuracy
of the test equipment: the use of a dead weight tester is highly
recommended.
The zero and span calibration screws are located behind the
Nameplate. To gain access slacken the nameplate screw and
rotate 90° ; proceed in the reverse mode when the calibration
procedure has been completed. Fig. 12 shows the calibration
screws: they provide two large plastic heads that can rotate 90°
in the direction indicated by the arrows, with spring-return to
normal. The calibration screws can be removed after the
calibration, to avoid improper use by inserting a screwdriver
blade below the plastic flange and pulling out.
Fig. 12 - Top view of the calibration screws
The calibration screws can be of type "Push buttons" with
exactly the same functionality; keep it pressed for at least two
seconds.
Power Supply
10.5 to 42 V. d.c.
55
Short circuit link
Precision
Milliameter
V.G.
H
A
B
M1
V.P.