Related Manuals for opticis IPKVM-500-ED
Summary of Contents for opticis IPKVM-500-ED
- Page 1 WWW.OPTICIS.COM 4K HDMI IPKVM Extender 25-0595/95 - IPKVM-500-ED User’s Manual Doc No. : OIPKVM-D161129 / Rev1.2 - 1 -...
-
Page 2: Table Of Contents
Index Product Description ........................- 3 - Main Features ..........................- 4 - Supporting Video Resolutions for Input / Output ................- 4 - Shipping Group ..........................- 4 - Systems Requirements for Setup ....................- 5 - Connector descriptions .........................- 6 - Setting Local / Remote Authority ....................- 8 - LED Indication ..........................- 8 - SW &... -
Page 3: Product Description
1. Product Description The OPTICIS 4K HDMI IPKVM Extender, IPKVM-500-ED is designed to distribute, control and access video with data (USB, RS-232, DIO and audio) anywhere over the standard IP Network. The transmitter, IPKVM-500-E (Encoder) connected to a HDMI source, encodes the video with data and transmits it over Ethernet. -
Page 4: Main Features
2. Main Features Extends HDMI/DVI, USB, RS-232, Audio, DIO over network Supports resolution up to 4K (3840x2160 at 30Hz) or full HD 1080p at 60Hz Any of transmitters in the network can be accessed by any receiver via provided PC program ... -
Page 5: Systems Requirements For Setup
Note: In some network switches, there may be a problem with video streaming because of capacity performance, even though they support these functions. * Opticis tested and confirmed the performance of L2 & L3 switches as below. So, opticis recommends user to use the switches for easy set-up. -
Page 6: Connector Descriptions
▶ Requirements: Windows XP and Window7 (and its higher versions). ♦ AC / DC Power Adapter Technical Advisory ▶ The IPKVM-500-ED is designed to use mainly external +5V AC / DC power adaptor. The internal power supplied through a HDMI pin (#18) from the graphic source is used to identify normal connection between a source and TX, IPKVM-500-E. - Page 7 Note1: If you change a video source to another one, you have to reset the power of all TXs and RXs by re-plugging of the +5V power adaptor. Note2: If you want to use the function of RS-232 & DIO, please contact sales@opticis.com. ♦ IPKVM-500-E, TX Back...
-
Page 8: Setting Local / Remote Authority
Refer to Page 21, “External Local/Remote Authority Setting”. 8. LED Indication IPKVM-500-ED has two (2) LEDs for Power and Authority status located on the front panels. ♦ Power status LED (Red) The red LED will be turned on when 5V power applied. -
Page 9: Sw & Factory Reset
♦ Link LED (Green) If the green LED turns on at TX and RX, it is ready to operate as IPKVM Extenders. 9. SW & Factory Reset ♦ SW Reset: Press the Reset switch on the back of devices shortly to reset ♦... -
Page 10: Remote Manager (Pc Program)
11. Remote Manager (PC Program) Note: IPKVM-500-ED supports static fixed IP address, auto IP address and DHCP IP (Dynamic Host Configuration Protocol: default) in IP network. Users can change auto IP to static IP with host & client device setup of PC Program if there is no DHCP server. -
Page 11: Device (Host /Client) Setting
4) Device (Host /Client) setting: It helps to find all TXs and RXs in the network and register automatically. But please remind that all TXs and RXs in the network should have different IP address. If you connect TXs and RXs in the network for the first time, please do modify network information of each TXs and RXs as below. -
Page 12: Advanced Setting: Configuration Of Bit Rate, Osd Display And Blocking
♦ ‘Reboot’ button: Re-boot selected device on the network if it needs. 5) Advanced Setting: configuration of Bit rate, OSD display and Blocking Default values are: Bit rate: 200(Mbps) / OSD: on / Blocking: disable/Jumbo frame enable Important: It recommends that these advanced settings are applied to all hosts or clients because all devices need to have same configuration for fast switching with bit rate and blocking and EDID data. -
Page 13: Edid Read/Write
(1) Select one between 50MHz~Best (2) Click ‘Save & Reboot’ to save and apply to TXs (All hosts is recommended). ♦ ODS on/off (1) Select on or off. (2) Click ‘Sync’ to save and apply to RXs. (Client All or selected client) * For details, please refer to Page 19 to figure out OSD mode. - Page 14 ♦ EDID read from a host (TX). (1) Select one of a host (TX) on the list. Connect a display to HDMI OUT receptacle of the selected TX over HDMI cable. (2) Click ‘Read EDID’ button. Then, you can see the saved EDID data as below. * The TX isn’t connected with display monitor, you can see ‘Fail’...
-
Page 15: Update Firmware
♦ EDID write from default EDID data to all hosts (recommended) After you check the default EDID data between HDMI and DVI on the top right, you can write the default EDID data to all TXs or selected one. Default EDID value is HDMI on the product. Select Default HDMI or Default DVI. - Page 16 - 16 -...
-
Page 17: Ipkvm-500Ed Connection & Operation
TX and 5 minutes for RX. (Do not unplug DC power until it finished) (5) Remove the USB memory stick from the device (IPKVM-350-E or D) 12. IPKVM-500-ED Connection & Operation 1) GUI Connection can be managed on a GUI of each client (RX) When TXs and RXs are in the TCP/IP network, you can see all hosts (TXs) with each IP addresses and device information on the GUI of a client (RX). -
Page 18: Operation With Audio Port
♦ Operation with HID KVM IPKVM-500-ED provides HID with a keyboard and a mouse. If you first connect mini-USB port of the host (TX) to USB port of PC source with USB cable, you are ready to use a keyboard and mouse in HID mode on remote or local site. -
Page 19: Multicast Streaming And Blocking Function
- Currently connected: this client (RX) is already connected to the host (TX). Note: When IPKVM-500-ED works as multicast mode, many client users may connect to a host. But first user who uses keyboard and mouse at first has priority. If the user does not use the keyboard and mouse for three (3) seconds, priority can be changed to another user. -
Page 20: Product Specifications
13. Product Specifications Item Description Network 100/1000 Base-T Ethernet: TCP/IP based wired network with CAT5e/ CAT6 Cables Resolution Up to 3840x2160@30Hz or 1080p@60Hz Video Interface Standard HDMI 1.4 and DVI1.0 HDCP HDCP 1.4 and 2.2 Multicast streaming 1 to N (up to 200 RXs) Video latency <... -
Page 21: External Local/Remote Authority Setting (Option)
14. External Local/Remote Authority Setting (Option) ♦ Console Switch & Console Indicator ▶ Console Switch (TX) The Console switch is to set Local or Remote control authority at an external switch for user’s convenience. Connect the console switch (left image) to DIO terminal block of the TX device by using a cable (right image). -
Page 22: Power Rack (Pr5V-16) General Specification
15. Power Rack (PR5V-16) General Specification *Image [Rear side] [Front] [Rear] - 22 -... -
Page 23: Trouble Shooting
- For technical support, visit Opticis web site, www.opticis.com or contact techsupp@opticis.com - When IPKVM-500-ED is first connected, it may need some more time (2~3 minutes) for recognizing USB Abnormal operation occurs driver on PC. in playing audio/video or... - Page 24 Abnormal operation occurs - When two or more users simultaneously try to access in KVM when a RX is trying an available host (TX), simultaneous connection happen Abnormal case to access to a TX. in specific time (4.5sec) (in blocking mode enabled) - Check another user on local site.
-
Page 25: Warranty Information
(1) year from the date of purchase from Opticis or its authorized resellers. If a product does not work as warranted during the applicable warranty period, Opticis shall, at its option and expense, repair the defective product or part, deliver to customer an equivalent product or part to replace the defective itemor refund to customer the purchase price paid for the defective product. - Page 26 Fax: +82 (31) 737-8039 For order support, please contact your Distributor Direktronik AB Konsul Johnsons väg 15 SE-149 45 Nynäshamn +46 8 524 00 700 info@direktronik.se www.direktronik.se For technical support, visit Opticis web site, www.opticis.com or contact techsupp@opticis.com or support@direktronik.se - 26 -...