Related Manuals for opticis IPKVM-310-ED
Summary of Contents for opticis IPKVM-310-ED
- Page 1 Ver. 1.0 WWW.OPTICIS.COM 16x16 Multicast supportable HDMI / DVI IPKVM Extender, IPKVM-310-ED User’s Manual Back Front ※ The design can be chaned without notice Doc No. : OIPKVM-D141001 / Rev1.0 - 1 -...
-
Page 2: Table Of Contents
Contents Welcome ..............................3 Prodcut Description ..........................3 Main Features ............................4 Network components ..........................4 Shipping Group ............................- 5 - Supporting video resolutions for Input / Output..................6 Application ..............................6 System requirements for setup ........................ 6 Installation ..............................7 Connection Ports ............................ -
Page 3: Welcome
IPKVM-310E, if it is connected to the source by USB interface. The IPKVM-310-ED supports the digital video data of full HD up to 1920x1080p at 60Hz and stereo audio and transmits the signal via Internet / Intra network. It also enables to distribute sixteen (16) video sources up to sixteen (16) displays in the multi-screen mode or the single-screen HD mode on the remote displays and makes sixteen (16) local keyboard and mouse accesses to the source. -
Page 4: Main Features
Main Features ♦ LAN standard: 802.3 Ethernet 10/100Mbps (TBD) ♦ Video Resolution: up to 1920x1080p@60Hz ♦ Monitoring Mode: 640x480, 16CH Multi-screen ♦ HID KVM mode: 1920x1080, 1CH Single-screen with HID Keyboard/Mouse ♦ H.264 CODEC ♦ OSD GUI, Multi-screen mode / Single-screen HD mode supported ♦... -
Page 5: Shipping Group
♦ PC Controller: Via a PC connected to the network, RemoteManager (PC program) manages user accounts, configures IP addresses of IPKVM-310EDs and provides user informations about each IPKVM connection. ♦ IP Network: An IP network what IP devices is connected via Switching hub. e.g Ethernet switching hub, Optical-Ethernet switch Shipping Group ... -
Page 6: Supporting Video Resolutions For Input / Output
Supporting Video Resolutions for Input / Output (TBD) IPKVM-310ED supports 3 kinds of resolutions and you have to fix one of them for same EDID. So a group of Rxs and Txs must have same resolution to display videos of Txs on 16ch multi-screen of Rxs. -
Page 7: Installation
♦ Control PC requirements ▶ We provides a PC program for management and monitoring. The program manages user accounts, configure IP addresses of IPKVM-310EDs and help user to know about each IPKVM connection. ▶ Requirements: Windows XP and Window7 (or above OS) ♦... -
Page 8: Connection Ports
Step 8 Connect LAN port (RJ45) in IPKVM-310-D (Rx) to LAN port in Network server with LAN cable. Step 9 Plug the +5V power adaptors to both IPKVM-310-E (Tx) and IPKVM-310-D (Rx). Note1: If you change an input source to another source, you have to reset the power of all Txs and Rxs by re-plging of the +5V power adaptor. - Page 9 Connect a source PC to this connector for the purpose of using HID mouse or Keyboard. ▶ USB A Type (Transmitter and Receiver) Connect a mouse and/or a keyboard to this connector for the purpose of using HID mouse or Keyboard. ▶...
- Page 10 ♦ IPKVM-310E Transmitter Back Power Jack HDMI Input HDMI Output RJ45 JACK (5V, 3.5mm) (Source) (Monitor) (LAN) ♦ IPKVM-310E Receiver front USB A for DIO RS232 Mouse/Keyboard (Terminal Block) ♦ IPKVM-310E Receiver back Power Jack HDMI Output RJ45 JACK (5V, 3.5mm) (Monitor) (LAN) - 10 -...
-
Page 11: Setting Local/Remote Authority
Setting Local/Remote Authority Note: You can use KVM (including an HID mouse and/or a keyboard, or a knob (or controller)) under user’s authority. You can access to the devices by a login with user ID and set user’s authority to Local or Remote state for purpose using Keyboard/Mouse. -
Page 12: Sw & Factory Reset
You can decide the authority on the 3-state slide switch of IPKVM-310E (Transmitter) among Local, Remote, or Console. If it set to Console on the 3-state slide switch, you can set the authority state to Local or Remote on the external console switch. And you can see same status via LEDs on the Console switch and Console Indicator. -
Page 13: Remotemanager (Pc Program)
Remote Manager (PC Program) 1) Installing PC Program Important: First of all, you should check the IP address and Gateway of the PC which should be set to the same IP class of the deviices,Txs and Rxs on Network setting of PC. eg. - Page 14 (2) Change the value of the password to another one. It is limited to 10 characters including numbers and English alphabets. (3) Add user IDs and passwords for general users. ▶ Click Mouse right button to add or modify the values. ▶...
- Page 15 (4) Press “Save” and “Sync” to save and use user accounts 4) Device(E/D) setting: to add, automatically detect and change device information. Note: You can register the devices such as transmitters (IPKVM-310E encoders) and receivers (IPKVM-310D decoder) to connect as a group of network connection. There are two methods: - You can automatically detect in the network and change devices and register those.
- Page 16 ♦ You can automatically detect the devices. This method is to find devices automatically and register easily if the devices, Txs and Rxs, are already connected in the network. (1) Firstly, check and enter IP class to find easily. eg. 192.168.0.xxx (2) Press “Start”...
- Page 17 ♦ You can change IP address of a transmitter or a receiver. (7) Click Mouse right button and slect ‘change IP’ to change to another IP address. - 17 -...
- Page 18 ♦ You may change to another port of change IP address in case of Rx device. (8) Click Mouse right button and slect ‘change port’ - 18 -...
- Page 19 ♦ You can read the current resolution of the device (for your information) (9) Click Mouse right button and select “resolution read” (10) You can see the current status about resolution of the device [both receivers and transmitters] - 19 -...
- Page 20 ♦ You can read and write the EDID of the connected monitor without using builted-in EDID. (11) Connect a monitor to HDMI/DVI port of the Receiver and recycle the power supply of selected device (12) Click Mouse right button and select “EDID read” (13) You can read and the EDID of the connected monitor (14) You can save the red EDID to PC for writing the EDID to a transmitter.
- Page 21 ♦ You can repeat [11]~[14] to read EDID of a transmitter except connecting a monitor to HDMI/DVI Loop-through port of the Transmitter - 21 -...
- Page 22 ♦ You can write the EDID to the transmitter from previously saved EDID data in PC. (15) Click Mouse right button and select “EDID write” (16) Select the EDID to the transmitter from previously saved EDID data in PC. And then you can see a message ,“EDID write OK, Device reboot” - 22 -...
- Page 23 ♦ You can reset device to reboot or recycle the power supply of selected device. (17) Click Mouse right button and select “reset device” ♦ You can select ‘change resolution’ of device individually. (18) Click Mouse right button and select “resolution change” ♦...
- Page 24 (19) Check another resolution and press the button, “Change All device resolution” Note: In cases of (17),(18) and (19), the devices are rebooted if those fuction is applied. 5) Receiver(D) setting ♦ You have to register a group of transmitters up to max. 16 to each receiver. Note: Before add the Tx IP to the list , firstly insert the name to each transmitter.
- Page 25 Press “Sync” button to save and use as a group of the list to each receiver. ♦ You can see the device name on each channel after login. (10) Backup and load of Setup environment which was already set in other PC You can easily use previous setup environment without complicated steps.
- Page 26 ♦ Backup (1) Select “backup” button on the top menu. (2) Select a file folder on the PC which you want to backup. ♦ Load (3) Firstly, copy and paste to the files backed up to a file folder on new PC. (4) Select “load”...
-
Page 27: Getting Started
Getting started 1) How IPKVM-310 works: 16CH multi-screen mode ♦ When 2 pairs of IPKVM-310ED have been connected, it will be totally showed as below. ▶ A Source (PC) is connected to the input port, HDMI IN, of the transmitter (E). ▶... - Page 28 3) Logging in ♦ When multi-pairs of IPKVM-310EDs (e.g 2 or 3 pairs) have been connected, it will be showed as below. ♦ On the remote (Receiver) site, 2 transmitters have been connected and it shows an initial view before logging in. (1) To access the Remote display, first, login with a user ID which is register in PC Program (RemoteManager).
- Page 29 4) Mode Change (1) To change to 1CH single screen mode, click mouse right button and select “Mode change” or doble click on selected channel. ♦ You can see on left corner that it operates as HID mode in the 1CH single-screen HD mode. Note: If you select a transmitter and change it to the single-screen HD mode for using it in HID KVM mode on a remote (receiver) site, you cannot use the transmitter on other receivers.
- Page 30 5) HID KVM mode ♦ You can use a keyboard and mouse in the HID KVM mode as below. ▶ You have to use the “Handy point” type mouse as main mouse in the HID mode. (1) To exit 1CH single-screen mode to 16CH multi-screen mode, move up “Hand type” mouse and click the “mode change”...
- Page 31 ♦ If the color of each framework is green, it says that you can work with the transmitter. Note. ▶ Green (available): You can work with the transmitter (Source) on the remote (receiver) site. ▶ Magenta (not available): You cannot work with the transmitter (Source) on the remote (receiver) site.
-
Page 32: Product Specifications
Product Specifications Item Description Multi-screen mode(16CH): VGA, 16CH simultaneously Monitoring mode Display mode Single-screen HD mode(1CH):1920x1080, 1CH HID KVM mode Network(LAN) 10/100 Base-T Ethernet: TCP/IP based wired network with CAT5e/ CAT6 Cables Video Streaming protocol RTSP, RTP, RTCP, UDP / TCPIP Video Codec MPEG-4 Part 10/AVC (H.264) Resolution... -
Page 33: Externally Setting Local/Remote Authority
Externally Setting Local/Remote Authority (Option) Console Switch & Console Indicator ♦ ▶ Console Switch (Tx) The Console switch is to set a Local or Remote state of control authority on an external switch for user’s convenience. Connect the console switch (left image) to DIO terminal block of the transmitter device by using a cable (right image). - Page 34 Connect the console indicator (left image) to DIO terminal block of the reciver device by using a cable (right image). And then, you can see the Local or Remote state of control authority through LED indication on the remote site. 1) 2pin Terminal Block Refer to below figures to know an method and order to 2pin terminal block +3.3V...
-
Page 35: Troubleshooting
Troubleshooting Problem Remedy Action Causes - Wait several seconds for the system booting. After the power is applied, Power status LED will turn on (Red). - Check the connection of all cables. Cables are No video on the display - Check the connection of the LAN cable to RJ45 connected (16CH multi-screen mode) -
Page 36: Warranty Information
(1) year from the date of purchase from Opticis or its authorized resellers. If a product does not work as warranted during the applicable warranty period, Opticis shall, at its option and expense, repair the defective product or part, deliver to customer an equivalent product or part to replace the defective itemor refund to customer the purchase price paid for the defective product. -
Page 37: Fcc/Ce Statement
other than from ordinary use or failure to properly use the product in the application for which said product is intended. Dispose of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate systems) This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. - Page 38 guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ♦...
- Page 39 #501 Byoksan Technopia, 560, Dunchon-daero, Jungwon-gu, Seongnam-si,Gyeonggi-do, 462-716 Rep. of KOREA Tel: +82 (31) 737-8033 Fax: +82 (31) 737-8039 For order support, please contact your Distributor or Reseller. For technical support, visit Opticis web site, www.opticis.com or contact techsupp@opticis.com - 39 -...