Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for JUKI IT-10
Summary of Contents for JUKI IT-10
- Page 1 ENGLISH IT-10 INSTRUCTION MANUAL...
-
Page 2: Table Of Contents
CONTENTS 1. INTROdUCTION ..................1 2. CONNECTING THE COUNT MANUAL SwITCH ........1 3. USB pORT ....................2 4. SETTING pROCEdURE Of THE MACHINE HEAd ......2 5. AdjUSTING THE MACHINE HEAd(dIRECT-dRIvE MOTOR TypE SEwING MACHINE ONLy) ..............3 6. SEwING pATTERN SETUp BLOCk (LEfT pANEL) ......4 6 -1. Configuration .......................... -
Page 3: Introduction
Be sure to read "Safety precautions" in the Instruction for the SC-920 (control box) before reading this Instruction Manual to fully understand them. IT-10 comprises of 2 panels with different functions. The left panel is used to set up the sewing pattern. For operation procedures, please see “6. -
Page 4: Usb Port
• Some type of the USB device may not be properly recognized by this sewing machine. • JUKI does not compensate for loss of data stored on the USB device caused by using it with this sewing machine. 2 USB specifications •... -
Page 5: Adjusting The Machine Head(Direct-Drive Motor Type Sewing Machine Only)
5. AdjUSTING THE MACHINE HEAd (dIRECT-dRIvE MOTOR TypE SEwING MACHINE ONLy) When the slip between the white marker dot on the handwheel and the concave of the cover is excessive after thread trimming, adjust the angle of the machine head by the operation below. 1) Simultaneously pressing switch 4 and switch 5 , turn ON the power switch. -
Page 6: Sewing Pattern Setup Block (Left Panel)
6. SEwING pATTERN SETUp BLOCk (LEfT pANEL) 6-1. Configuration Button and display Description Used for changing over effective/ineffective of the reverse feed stitching switch : pattern. Used for changing over effective/ineffective of the overlapped stitching switch pattern. Used for confirming the contents of setting and for changing over effec- switch tive/ineffective of the reverse feed stitching at sewing start. -
Page 7: Operating Procedure Of The Sewing Pattern
6-2. Operating procedure of the sewing pattern (1) Reverse feed stitching pattern Reverse feed stitching at sewing start and reverse feed stitching at sewing end can be separately programmed. [Setting procedure of the reverse feed stitching] 1) Effective/ineffective of the reverse feed stitching pattern can be changed over by pressing switch 1 . When the reverse feed stitching pattern is ren- dered effective, LED C lights up, the number of stitches of the reverse feed stitching at sewing start is displayed on A , and the number of stitch-... -
Page 8: Overlapped Stitching Pattern
(2) Overlapped stitching pattern Overlapped stitching pattern can be programmed. A : Number of stitches of normal stitching setting 0 to 15 stitches B : Number of stitches of reverse stitching setting 0 to 15 stitches C : Number of stitches of normal stitching setting 0 to 15 stitches D : Number of times of repetition 0 to 9 times... -
Page 9: One-Touch Setting
6-3. One-touch setting A part of function setting items can be easily changed in the normal sewing state. [One-touch setting procedure] 1) Keep switch 7 held pressed for one second to place the panel in the function setting mode. 2) Change over the item to be set by using switch 3 or switch 4 . -
Page 10: Production Support Function
6-4. Production support function The production support function consists of three different functions (six different modes) such as the produc- tion volume management function, operation measuring function and bobbin counter function. Each of them has its own production support effect. Select the appropriate function (mode) as required. ■... - Page 11 Sewing can be performed with the production support data displayed on the control panel. [Basic operation of the production support modes] 1) When switch 7 is pressed in the nor- mal sewing state, LED E lights up to enter the production support mode. 2) Production support function can be changed over by pressing switch 3 or switch 4 .
- Page 12 Table 2: Mode resetting operation Switch 5 Switch 5 (held pressed for 2 (held pressed for 4 sec- Mode name seconds) onds) Target No. of pcs. display mode Resets the actual number of pieces Resets the difference between tar- (F100) get number of pieces and actual number of pieces Target/actual No.
-
Page 13: Setting Of Functions
6-5. Setting of functions Functions can be selected and specified. ※ Refer to the Instruction Manual for the control box for details of the function setting. 1) Turn ON the power with switch 7 held pressed. (The item which has been changed during the previous work is displayed.) * If the screen display does not change, re-carry out operation described in step 1). -
Page 14: Production Management Data Measurement Block (Right Panel)
7. pROdUCTION MANAGEMENT dATA MEASUREMENT BLOCk (RIGHT pANEL) 7-1. Configuration D E F Switch/indication Description Clock LED Lights up when the clock is displayed. 7-segment indication block Indicates various ID data and clock information. Lights up when Product No. ID is displayed on Product No. -
Page 15: Normal Startup Mode
7-2. Normal startup mode When the power supply is turned on, the item screen and ID data which had been selected before it was turned off in the previous operation. The selected item and the number for which the ID is registered are indicated in LED. When the No. -
Page 16: Normal Startup Mode Screen
(1) Normal startup mode screen ■ Product No. display screen Press the switch is pressed. After 3 seconds The 16-digit Product No. ID is indicated. A registered ID can be set up from the No. switch. Press the switch is pressed. ■ Clock indication Operator ID display screen P r e s s t h e ■... -
Page 17: No. Switch Input Procedure Under Normal Startup Mode
ID is indicated successively from the first 4 digits. If the ID is 1234 5678 9ABC DEFG, it is indicated as follows and the indication switches to the clock when the entire ID is indicated. After 1.5 seconds After 1.5 seconds Clock indication After 3 seconds After 1.5 seconds Whether the clock is automatically displayed after 3 seconds or by pressing the switch can be selected using the memory switch. When the setting to display the clock with the switch is selected, the selected ID is indicat- ed by pressing the memory switch. (2) No. switch input procedure under normal startup mode When the 2 out of the 1 to 5 No. switches are pressed successively, ID can be selected from 30 different IDs. It is considered one-switch operation if one No. -
Page 18: List Of No. Input Patterns By Switches
(3) List of No. input patterns by switches indication : Lights up. indication : Blinks. First switch Second switch First switch Second input input input switch input After 1 second After 1 second After 1 second After 1 second After 1 second When No.30 (switches ) is input, ID will be unselected. – 16 –... -
Page 19: Outputting Measurement Data
(4) Outputting measurement data When switch 1 is pressed for one second or longer under normal mode, USB data writing func- tion is enabled. When switch 2 is pressed for one second or longer, network data transmission function is enabled. “Wait” blinks on the 7-segment indication block dur- ing data output. -
Page 20: Setup Mode
7-3. Setup mode (1) Setup mode screen When the power supply is turned on with switch pressed, the system starts up in setup mode. Press the switch. In setup mode, the setting item is selected by using MAC address check screen ■ Initialization screen ■ switches and Press the switch. -
Page 21: Mac Address Check Screen
(2) MAC address check screen Since MAC address is set up for each device, it can only be checked on the IT panel. Press the switch 3 to switch the block indica- tion for MAC address. – 19 –... -
Page 22: Memory Switch Setup Screen
(3) Memory switch setup screen Panel operation can be varied by changing the memory switch setting. Press the switch 3 on the memory switch setup screen and display the memory switch No. The memory switch can be selected by pressing switch 1 or switch 2 in this condition. When the memory switch has been selected, press switch 3 to indicate the setting value A for the selected memory switch. - Page 23 ■ Memory Switch Data List Description Initial value Network offline setting Network connection validity/invalidity is selected. OFF : Network connection is enabled. ON : Network connection is prohibited. Clock correction function Clock correction validity/invalidity when there is network connection is set up. OFF : Clock correction is not enabled. ON : The panel clock is corrected in reference to the host PC clock when there is net- work connection.
-
Page 24: Clock Setup Screen
(4) Clock setup screen The year, month, date, hour, minute and second are set up on the clock setup screen. Press switch 1 or switch 2 to enter the date and time. Then, confirm the entry by pressing switch 3 . ■ Clock setup screen Hour setting ■... -
Page 25: Initialization Screen
(5) Initialization screen Panel data is initialized on the initialization screen. Press the switch 3 on memory switch initial- ization screen and indicate the initialization No. The initialization No. can be selected by pressing the switch 1 or switch 2 in this condition. 0 : Initialization is not executed. -
Page 26: Usb Format Screen
(6) USB format screen The external medium connected at the USB is formatted on the USB format screen. “YES” is displayed when the switch 3 is pressed on the USB format screen. “YES” and “NO” are switched by pressing the switch 1 or switch 2 . -
Page 27: Ip Address Setup Screen
(7) IP address setup screen The method to obtain the IP address is selected on the IP address setup screen. ■ IP address mode selection Select the method by pressing the switch 1 or switch 2 with the IP address mode selected, and confirm the selection by pressing the switch 3 . -
Page 28: Version Check Screen
Manual selection of IP address ■ When manual input is selected, the IP address input screen will appear. Select the IP address using the switch 1 or switch 2 for each block and then confirm with the switch 3 . * The screen will blink during setup. …... -
Page 29: Software Rewrite Mode
7-4. Software rewrite mode When the power supply is turned ON with switch pressed, the system will start up in IT-10 application software rewrite mode. When the power supply is turned ON with switch pressed, the IT-10 is placed in the servomotor software update mode. -
Page 30: Automatic Compensation Of Neutral Point Of The Pedal Sensor
8. AUTOMATIC COMpENSATION Of NEUTRAL pOINT Of THE pEdAL SENSOR Whenever the pedal sensor, spring, etc. are replaced, be sure to perform following operation : 1) Pressing switch 4 , turn ON the power switch. 2) Compensated value is displayed on indica- tor B . -
Page 31: Setting Of The Auto Lifter Function
10. SETTING Of THE AUTO LIfTER fUNCTION WARNING : When the solenoid is used with the air drive setting, the solenoid may be burned out. So, do not mistake the setting. When the auto-lifter device (AK) is attached, this function makes the function of auto-lifter work. 1) Turn ON the power switch with switch 5 held pressed. 2) "FL ON" is displayed on indicators A and B with a blip to make the auto lifter function ef- fective. -
Page 32: Selecting Procedure Of The Key-Lock Function
11. SELECTING pROCEdURE Of THE kEy-LOCk fUNCTION Setting of the number of stitches for a pattern can be prohibited by enabling the key lock function. 1) Turn ON the power switch with switch 5 and switch 6 held pressed. 2) "KEY LOCK" is displayed on indicators A and B with a blip to make the key-lock function effective. -
Page 33: Error Indication
13. ERROR INdICATION This system enables interlock (or restriction of functions) to prevent the problem from spreading in case a prob- lem is detected, and contains the following error codes to notify the problems. When requesting for service, please also check the error code.Refer to the Instruction Manual for the control box errors on the control box. Error code display Error code Error description...