Vehicle connections
The connection information listed below is specific to the 2016 Dodge/Ram 1500. Refer to "Pre-installation and application warnings" for a list of important notes.
Data 14-pin blue connector (H1)
Module
Conn./Pin
Color
H1/1
Light Green
H1/2
Violet/Yellow
H1/3
Tan/Black
H1/4
Tan
H1/5
Orange/Green
H1/6
Orange/Brown
H1/7
Brown
H1/8
Yellow
H1/9
Orange/Yellow
H1/10
Orange/Red
H1/11
Yellow/Red
H1/12
Brown/Red
H1/13
Red
H1/14
Black
Output 12-pin red connector (H2)
Module
Conn./Pin
Color
H2/1
Black/White
H2/2
Green/Black
H2/3
Green/White
H2/4
Red/Black
H2/5
Violet/White
H2/6
Gray
H2/7
Gray/Black
H2/8
Violet/Green
H2/9
Violet/Brown
H2/10
Yellow/Black
H2/11
Orange/Black
H2/12
Blue/Red
Input 10-pin black connector (H3)
Module
Conn./Pin
Color
H3/1
Green
9
Description
No Connection
No Connection
(DATA) HS CAN High
(DATA) HS CAN Low
(DATA) HS CAN High [2]
(DATA) HS CAN Low [2]
Relay N.O. No Connection
Relay COM Immo Data
Relay N.C. Immo Data
Relay N.C. No Connection
Relay COM Ignition Output
Relay N.O. 12 Volt
(+) W2W Only - 12 Volt
(-) W2W Only - Ground
Description
(-) W2W Only - E-Brake Output
No Connection
(-) W2W Only - Door Output
(-) W2W Only - Trunk Output
(AC) W2W Only - Tach Output [1]
(+) W2W Only - Brake Output
(+) Ignition Output
No Connection
(MUX) Pk Light Output
(Data) Immo Data
(-) RAP Off
(-) W2W Only - Hood Switch Input
Description
(-) W2W Only - Lock Input
Connects To
Wire Location
No Connection
No Connection
OBD-Data Link Connector, black 16 pin plug, pin 6
OBD-Data Link Connector, black 16 pin plug, pin 14
OBD-Data Link Connector, black 16 pin plug, pin 3
OBD-Data Link Connector, black 16 pin plug, pin 11
No Connection
Ignition Node (ignition switch), black 6 pin plug, pin 5
Ignition Node (ignition switch), black 6 pin plug, pin 5
No Connection
Ignition Node (ignition switch), black 6 pin plug, pin 4
BCM under driver dash, black 4 pin plug (B), pin 3
BCM under driver dash, black 4 pin plug (B), pin 3
Connects To
Wire Location
Remote Starter
No Connection
Remote Starter
Remote Starter
Remote Starter
Remote Starter
Ignition Node (ignition switch), black 6 pin plug, pin 4
No Connection
BCM under driver dash, blue 24 pin plug (G), pin 20
Ignition Node (ignition switch), black 6 pin plug, pin 5
BCM under driver dash, white 48 pin plug (F), pin 9
Remote Starter
Connects To
Wire Location
Remote Starter
(+/-)
Wire Color
Ref.
Data
Gray/White (CAN C)
Data
Yellow (CAN C)
Data
Gray (CAN IHS)
Data
White (CAN IHS)
Data
White/Lt. Green
Data
White/Lt. Green
+
Violet/Brown
+
Red (40A)
+
Red (40A)
(chassis ground)
(+/-)
Wire Color
Ref.
+
Violet/Brown
MUX
White/Brown
Data
White/Lt. Green
-
Violet
(+/-)
Wire Color
Ref.
403.CHRYSLER6 2.04 2016 Dodge/Ram 1500
© 2018-01-30 Directed. All rights reserved.
Need help?
Do you have a question about the DB3 and is the answer not in the manual?
Questions and answers
Installing on a 2006 gmc sierra
To install the Directed DB3 on a 2006 GMC Sierra:
1. Use a professional installer: The product is intended for installation by trained professionals only.
2. Use the correct wiring: Follow the wiring diagram specific to the vehicle. If using a T-Harness (model THCHD3), refer to the T-Harness wiring diagram.
3. Locate components: Identify and access the necessary vehicle components for connection using the guide provided.
4. Connect the module: Make all wire connections as shown in the wiring diagram. Ensure secure and proper connections to avoid electrical system damage.
5. Program the module: Follow the module programming steps to initialize and configure the DB3 for the 2006 GMC Sierra.
6. Test the system: Use the LED diagnostics and troubleshooting section to verify proper operation and resolve any errors.
7. Perform reset or feature programming if needed: Use soft/hard reset or feature programming steps based on installation results.
Professional installation is strongly recommended to prevent vehicle damage.
This answer is automatically generated