Contents Introduction Vehicle function compatibilities Pre-installation and application warnings Key type Wiring Diagram Locating components in the vehicle Vehicle connections Module programming With transponder and CAN Without transponder with CAN Connecting the module LED diagnostics and troubleshooting Soft reset Hard reset Feature programming Feature and option list Limited one year consumer warranty...
Vehicle function compatibilities This section lists all the functions compatible with this vehicle for the installation illustrated in this guide. Arm Factory Security Entry Monitoring ALL Door Pins Disarm Factory Security Entry Monitoring Driver Door Pin Door Lock Control Entry Monitoring Hood Pin Door Unlock Entry Monitoring Trunk/Hatch Pin Driver Priority Unlock...
Pre-installation and application warnings Firmware notes: This section highlights important information for this specific firmware and will assist in pricing accordingly, as well as bringing awareness to any operational or vehicle limitations. T-Harness Keys required for Keys required for compatible programming operation Important!
Key type Some Toyota 2010+ models have different encryption types. Please look at your key blade and identify the markings. H-stam ped keys G-stam ped keys Standard Key For vehicles with H-stamped keys, see For vehicles with G-stamped keys, see For vehicles with dot-stamped keys, the TL10 firmware.
Wiring diagram Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( XKD2D65 HS CAN High: Pin 6 OBDII Plug Headlight Switch Black Connector (white conn. at headlights) HS CAN Low: Pin 14 (-) Parking Lights: Pin 18 D2D Port...
Vehicle connections The connection information listed below is specific to the 2010 Toyota Camry. Refer to “Pre-installation and application warnings” for a list of important notes. Data 14-pin blue connector (H1) Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color H1/1 Light Green...
Page 10
Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color H3/1 Green (-) W2W Only - Lock Input Remote Starter H3/2 Blue (-) W2W Only - Unlock Input Remote Starter H3/3 Red/White (-) W2W Only - Trunk Input Remote Starter H3/4 White/Violet No Connection...
Module programming Refer to “LED diagnostics and troubleshooting” for more information and for troubleshooting purposes. With transponder and CAN Please review all module programming procedures to determine which one is compatible with your specific vehicle. Wait until the LED turns ON solid red. Insert the key in the ignition switch.
Without transponder with CAN Wait until the LED turns ON solid red. Press the programming button 5x to skip transponder programming. The LED turns ON solid orange. Insert the key in the ignition switch. Turn the key to the ON position. The LED flashes orange once then turns ON solid for 3 secs then shuts OFF.
Connecting the module Important! Make all the required connections to the vehicle, as described in this guide, and double check to ensure everything is correct prior to moving onto programming. Warning! To take advantage of advanced features, you must use DirectLink 4.5 (and higher) or the Directechs Mobile application. Flashing a module using your computer: 1.
LED diagnostics and troubleshooting This section provides LED diagnostics and troubleshooting information to guide you through the various stages of your installation. Module Programming Description Troubleshooting Make sure the D2D harness is connected and that 12 Volt is present between the red and black wires. If Module has no power.
Page 15
External Module Synchronization Description Troubleshooting OBDII feature not supported. The diagnostic data bus was not detected, therefore the SmartStart features will be limited. (Flashes red, red, then orange) x 10 Active Ground When Running (Status) Description Troubleshooting Ground When Running (Status) command The module has initialized the remote start sequence.
Soft reset A module reset will only erase the steps perfomed in “Module programming”. The firmware and settings flashed to the module will not be affected. D2D installation Connect the 10-pin, 12-pin & 14-pin harnesses to the module. Press and hold the programming button, then connect the 4-pin D2D harness.
Feature programming To enter feature programming routine: 1. Turn the ignition ON, then OFF. 2. Within 5 seconds, press and hold the programming button until the LED turns ON orange (after 3 seconds). 3. Release the Programming button. 4. The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate the current option of feature 1 (e.g.
Feature and option list It is recommended to configure all the features and options listed below using the configuration tool found on the module flashing page at www.directechs.com. The web offers more options; however, manual configuration of the features is possible using the information on this page.
Limited 12 Months Consumer Warranty VOXX DEI LLC (the Company) warrants to the original purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 12 months from the date of original purchase, such defect(s) will be repaired or replaced with new or reconditioned product, (at the Company’s option) without charge for parts or repair labor.
Factory remote. Press the Remote Start button on the transmitter.* • Aftermarket remote. • Directed SmartStart application via your smartphone. & The parking lights will flash once to indicate the Parking lights flash x1 Press Remote vehicle is now in Pit Stop Mode.