Table of Contents
Advertisement
The LANGUAGE SETUP PAGE
. .
. .
Language Setup Page
Video Setup Page
OSD Language
Disc Menu
Audio
Subtitle
Go to language setup page
OSD LANGUAGE
ENGLISH
Default setting:
Sets the language of the SETUP MENU. Changing this setting
to your native language will make using the SETUP MENU
much easier.
DISC MENU
Default setting:
ENGLISH
Sets the default language for discs containing multiple menu
languages. This setting is only applicable to discs that contain
a menu in the language you choose, otherwise the default
menu on the disc will be used.
AUDIO
Default setting:
ENGLISH
Sets the default language for discs containing multiple
language tracks. This setting is only applicable to discs that
offer the language specified. Unsupported discs will play the
default language on the disc.
SUBTITLE
Off
Default setting:
For discs that support multiple subtitle languages. Set the
default subtitle language you would like to see. This setting is
only applicable to discs that support the language you specify,
otherwise the default subtitle track on the disc will be shown.
The VIDEO SETUP PAGE
. .
. .
Video Setup Page
Video Setup Page
TV Display
TV Type
Video Output
Video Mode
P - Scan Mode
Video Quality
Go to video setup page
TV DISPLAY
Default setting:
WIDE
You can setup your DVD Player to work with normal and wide
screen televisions. If you are using a wide screen TV, set this
WIDE 16:9
option to
to match the aspect ratio of your TV.
When used with a normal TV (4:3 aspect ratio), the
NORMAL/PS4:3
setting results in the typical "Pan & Scan"
display, where a movie is clipped on the sides to fit into the TV
screen. The
NORMAL/LB4:3
THE DVD PLAYER SETUP MENU
. .
. .
ENG
ENG
ENG
Off
. .
. .
Wide
NTSC
S - VI
Auto
setting will enable the
"Letterbox" format, where the movie is presented in wide
screen format with black lines at the top and bottom of the
PS4:3
screen. Note: The
since very few movies support both options. DVDs are generally
recorded with either PS or LB and do not allow switching
between the two.
TV TYPE
Default setting:
NTSC
Your DVD Player will work with TVs based on the NTSC and
PAL standards, as well as TVs designed to function with both
standards, or "Multi" models. NTSC is the standard TV system
used in the USA, Canada, Japan and many other countries. The
PAL TV system is used in Europe, Africa and the Middle East,
among other places. Refer to your TV's documentation to make
sure which model you have.
VIDEO OUTPUT
S-VI
Default setting:
After pressing the monitor key to output audio and video to an
external source, the function can be activated.
Ÿ
S-VIDEO:
A higher quality picture than standard
COMPOSITE VIDEO. The
composite and S - Video connections.
Ÿ
YUV:
This setting is used for TVs supporting component
video out and progressive scan. To activate the component
video outputs, you must first connect the unit using the
COMPOSITE VIDEO connector and cable in order to enter
SETUP and change this setting. Next, connect the unit using
the COMPONENT VIDEO cables and unplug the
COMPOSITE video cable. Adjust the TV's Video Input
setting to correspond to the COMPONENT Input.
VIDEO MODE
Default setting:
INTERLACE
Most TVs scan only half the lines of an image in one pass. This
scanning method is known as "interlaced" mode, as the odd and
even lines are interlaced together in alternate scans. Progressive
P-SCAN
scan, or
, is a scanning method offered on high-end
TVs. Progressive scan TVs scan all the lines of an image in one
pass, creating a more film-like quality to DVD movies.
Note: This setting is only available when the
setting is set to
YUV
. This is because all progressive scan TVs
require component video inputs. If this setting is inadvertently
set to
P-SCAN
, reset the video to
the disc tray and pressing
control.
P - SCAN MODE
AUTO
Default setting:
FILM
3:2 is for NTSC - Converts 24 frame/sec film to 30
frame/sec NTSC video.
frame/sec film to 25 frame/sec PAL video.
automatically between the modes depending on the disc
inserted. Note : this option can be selected only while the Video
Mode is set to P-Scan.
32
LB4:3
and
usually will have no effect,
S - Video
setting is used with
VIDEO OUTPUT
INTERLACED
DISPLAY - 1 - 2 - 3
on the remote
VIDEO
2:2 is for PAL - Converts 24
AUTO
by opening
switches
Advertisement
Table of Contents
