Page 1
30-100 8” Benchtop Drill Press Operator’s Manual Record the serial number and date of purchase in your manual for future reference. Serial Number: _________________________ Date of purchase: _________________________ For technical support or parts questions, email techsupport@rikontools.com or call toll free at (877)884-5167 www.rikontools.com...
Changes and improvements may be made at any time, with no obligation on the part of Rikon Power Tools, Inc. to modify previously delivered units. Reasonable care has been taken to ensure that the information in this manual is correct, to provide you with the guidelines for the proper safety,...
SAFETY INSTRUCTIONS IMPORTANT! Safety is the single most important consideration in the operation of this equipment. The following instructions must be followed at all times. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury. There are certain applications for which this tool was designed.
Page 4
SAFETY INSTRUCTIONS 12. KEEP PROTECTIVE GUARDS IN PLACE AND IN 25. ALWAYS WEAR A DUST MASK TO PREVENT WORKING ORDER. INHALING DANGEROUS DUST OR AIRBORNE PARTICLES, including wood dust, crystalline silica dust 13. AVOID ACCIDENTAL STARTING. Make sure that and asbestos dust. Direct particles away from face and the power switch is in the “OFF”...
SAFETY INSTRUCTIONS EXTENSION CORDS ELECTRICAL SAFETY THE USE OF AN EXTENSION CORD THIS TOOL MUST BE GROUNDED WITH THIS MACHINE IS NOT RECOMMENDED. For WHILE IN USE TO PROTECT THE OPERATOR FROM best power and safety, plug the machine directly into a ELECTRIC SHOCK.
Page 6
SAFETY INSTRUCTIONS SPECIFIC SAFETY INSTRUCTIONS FOR DRILL PRESSES This machine is intended for the drilling of solid woods, composites, plastics and metals. The permissible workpiece dimensions must be observed (see Technical Specification). Any other use not as specified, including modification of the machine or use of parts not tested and approved by the equipment manufacturer can cause unforeseen damage and invalidate the warranty.
GETTING TO KNOW YOUR MACHINE Base Belt Cover Motor Table Lock Handle Table Motor/Belt Adjusting Knob Table Tilt Locking Screw Feed Handles Chuck Column Support Tube Handle Return Spring Chuck Key Holder Depth Stop On/Off Safety Switch CONTENTS OF PACKAGE Unpacking and Clean-up 1.
ASSEMBLY THE MACHINE MUST NOT BE PLUGGED IN AND THE POWER SWITCH MUST BE IN THE 'OFF' POSITION UNTIL ASSEMBLY IS COMPLETE. Tools Required for Assembly Phillips Screwdriver Adjustable or 13mm Wrench Unpacking and Clean-up 1. Carefully finish removing all contents from shipping carton. Compare contents of the shipping carton with the list shown on page 8.
Page 10
ASSEMBLY THE MACHINE MUST NOT BE PLUGGED IN AND THE POWER SWITCH MUST BE IN THE 'OFF' POSITION UNTIL ASSEMBLY IS COMPLETE. 3. Slide the drill press head onto the column. FIG. 3. 4. Center the drill press head over the table and base.
ADJUSTMENTS 8. DEPTH STOP: The depth stop and scale are found on the left side of the switch box. To adjust, lower the drill chuck until the pointer shows your desired depth on the scale. Loosen the lower nut on the threaded shaft (FIG.
ADJUSTMENTS THE MACHINE MUST NOT BE PLUGGED IN AND THE POWER SWITCH MUST BE IN THE 'OFF' POSITION UNTIL ADJUSTMENTS ARE COMPLETE. 11. CHANGING SPINDLE SPEEDS: The 30-100 Bench Drill Press has five spindle speeds. To change; A. Lift the cover with the handle to reveal the motor and spindle pulleys, and drive belt.
MAINTENANCE Turn the power switch “OFF” and disconnect the plug from the outlet prior to adjusting or maintaining the machine. DO NOT attempt to repair or maintain the electrical components of the motor. Contact a qualified service technician for this type of maintenance. 1.
PARTS DIAGRAMS & PARTS LISTS - C & D MFGR. DESCRIPTION PART NO. MFGR. Gasket - Quill P30-100-1C Ball Bearing - 12mm P30-100-2C DESCRIPTION PART NO. Tube - Quill P30-100-3C Support - Table with Scale Screw - Pan M5x0.8-20 P30-100-4C P30-100-1D Support - Lock Handle Stop Collar...