B&G Zeus3 Glass Helm Installation Manual
Hide thumbs Also See for Zeus3 Glass Helm:

Advertisement

Zeus
Glass Helm
3
Installation Manual
ENGLISH
www.bandg.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Zeus3 Glass Helm and is the answer not in the manual?

Questions and answers

jouault
June 9, 2025

find reset

Summary of Contents for B&G Zeus3 Glass Helm

  • Page 1 Zeus Glass Helm Installation Manual ENGLISH www.bandg.com...
  • Page 3 Warning The user is cautioned that any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Preface | Zeus3 Glass Helm Installation Manual...
  • Page 4 MB type internet connection may require large data usage. Your service provider may charge you based on the amount of data you transfer. If you are unsure, contact your service provider to confirm rates and restrictions. Preface | Zeus3 Glass Helm Installation Manual...
  • Page 5: About This Manual

    Used to draw the reader’s attention to a comment or some important information. Warning: Used when it is necessary to warn personnel that they should proceed carefully to prevent risk of injury and/or damage to equipment/ personnel. Preface | Zeus3 Glass Helm Installation Manual...
  • Page 6: Table Of Contents

    Accessing the settings dialog System settings Alarms settings Radar settings Echosounder settings Autopilot settings Fuel settings Wireless settings Network settings 36 3rd party support C-Zone 37 Appendix Accessories Supported data Technical specifications Dimensional drawings Contents | Zeus3 Glass Helm Installation Manual...
  • Page 7: Introduction

    1 set silver bezels Power cable, fuse, fuse holder and connector block RJ45 to 5-pin Ethernet adapter cable NMEA 0183 connector block Documentation pack Cable retainer kit NMEA 2000 starter kit Panel mounting kit Introduction | Zeus3 Glass Helm Installation Manual...
  • Page 8: Front Controls

    HDMI OUT - HDMI video output VIDEO IN - composite video input HDMI IN - HDMI video input NMEA 0183 - NMEA 0183 data POWER - 12 - 24 V DC input, external alarm and power control Introduction | Zeus3 Glass Helm Installation Manual...
  • Page 9: Card Reader

    If the card reader has a protective door it should always be securely shut immediately after inserting or removing a card, in order to prevent possible water ingress. Introduction | Zeus3 Glass Helm Installation Manual...
  • Page 10: Installation

    Refer to the technical specifications in the on page 37. "Appendix" Bezel fitment and removal Ú Note: The unit in the illustration is an example only. Installation | Zeus3 Glass Helm Installation Manual...
  • Page 11: Cable Retainer Installation

    Panel mounting Refer to the separate mounting template for panel mounting instructions. Bracket mounting For bracket mounting refer to separate documentation supplied with the bracket kit (sold separately). Installation | Zeus3 Glass Helm Installation Manual...
  • Page 12: Wiring

    Yellow Power connection The unit is designed to be powered by a 12 or 24 V DC system. It is protected against reverse polarity, under voltage, and over voltage (for a limited duration). Wiring | Zeus3 Glass Helm Installation Manual...
  • Page 13: External Alarm

    Connect the yellow wire to the red wire after the fuse. Ú Note: The unit cannot be powered down by power button, but can be put in to standby mode (the screen backlight turns off). Wiring | Zeus3 Glass Helm Installation Manual...
  • Page 14 This will power on both other power master units and power slave units. If a unit is set to power control slave, it cannot be powered down using its Wiring | Zeus3 Glass Helm Installation Manual...
  • Page 15: Usb Connector Details

    Talkers and listeners Only one talker (output device) can be connected to a serial input (RX) on the unit, in accordance with the NMEA0183 protocol. However, an output port (TX) on the unit may be Wiring | Zeus3 Glass Helm Installation Manual...
  • Page 16: Nmea 2000 Connector Details

    The backbone needs to have a terminator at each end of the backbone. The terminator can be a terminator plug or a unit with built-in terminator The following drawing demonstrates a typical network. NMEA 2000 device Drop-cable Terminator Wiring | Zeus3 Glass Helm Installation Manual...
  • Page 17: J1939 Connector Details

    Unit socket (male) Cable plug (female) Purpose Shield Not used CAN GND NET-H NET-L Engine connection For information about connecting an engine to the J1939 interface refer to the documentation supplied by the engine manufacturer. Wiring | Zeus3 Glass Helm Installation Manual...
  • Page 18: Ethernet Connector Details

    The video images will not be shared with another unit via the network. It is only possible to view video on the unit connected to the video source. Ú Note: Both NTSC and PAL formats are supported. Wiring | Zeus3 Glass Helm Installation Manual...
  • Page 19: Hdmi Connector Details

    If the unit has a HDMI input it can be connected to an external video source and display video images on its display. Configurations to video in are made in the video panel, refer to the Operator Manual for more information. Wiring | Zeus3 Glass Helm Installation Manual...
  • Page 20: Software Setup

    Configures the action of the WheelKey on the front of the unit. Power control setup Determines unit response to signal applied to the power control wire. Refer to "Power control connection" on page 13. Software setup | Zeus3 Glass Helm Installation Manual...
  • Page 21 This is achieved by entering position offsets for the GPS sensor. These offsets combined with heading data will allow the software to accurately determine the bows distance from the start line. Software setup | Zeus3 Glass Helm Installation Manual...
  • Page 22: Alarms Settings

    In a system with more than one radar, the correct device to configure can be selected from this menu. Ú Note: Radars that support dual radar mode are represented twice in the source list, with an A and B suffix. Software setup | Zeus3 Glass Helm Installation Manual...
  • Page 23 • Point the boat towards the jetty • Adjust the gain setting until a reasonably good image of the jetty echo is displayed Software setup | Zeus3 Glass Helm Installation Manual...
  • Page 24: Echosounder Settings

    This option can be used to revert all user adjustments. Echosounder settings A compatible echosounder module (or another unit which has built-in sonar) shared over the Ethernet network is required to view echosounder images on the unit. Software setup | Zeus3 Glass Helm Installation Manual...
  • Page 25 Use depth and temp data from Selects from which source the depth and temperature data is shared on the NMEA 2000 network. Installation Use this dialog to setup and configure available Echosounder sources. Software setup | Zeus3 Glass Helm Installation Manual...
  • Page 26 SOG records 10 knots (11.5 MPH) the calibration value needs to be increased to 117 %. To calculate the adjustment, divide the SOG by the paddlewheel speed, and multiply the product by 100. Calibration range: 50-200 %. Default is 100 %. Software setup | Zeus3 Glass Helm Installation Manual...
  • Page 27: Autopilot Settings

    Device list. For general source selection information, refer to "Network settings" on page 31. Vessel setup The Vessel setup dialog must be used to select the number of engines, the number of tanks and vessel’s total fuel capacity across all tanks. Software setup | Zeus3 Glass Helm Installation Manual...
  • Page 28 This assumes reasonably even fuel consumption on all engines. Ú Note: The Calibrate option is only available when Set to full is selected, and a Fuel Flow is connected and set up as a source. Software setup | Zeus3 Glass Helm Installation Manual...
  • Page 29: Wireless Settings

    When viewing this menu for a WIFI-1 set to Access Point mode, it’s also possible to switch between Primary and Secondary access point modes so two WIFI-1 devices can exist on the network at the same time. Software setup | Zeus3 Glass Helm Installation Manual...
  • Page 30 DHCP servers on a network, dhcp_probe may be run from the Zeus³ Glass Helm. Only one DHCP device may be operational on the same network at a time. If a second device is Software setup | Zeus3 Glass Helm Installation Manual...
  • Page 31: Network Settings

    The Auto Select option looks for all sources connected to the device. If more than one source is available for each data type, selection is made from an internal priority list. This option is suitable for the majority of installations. Software setup | Zeus3 Glass Helm Installation Manual...
  • Page 32: Device List

    Ú Note: Setting the instance number on a 3rd party product is typically not possible. Diagnostics Provides information useful for identifying an issue with the network. Software setup | Zeus3 Glass Helm Installation Manual...
  • Page 33 (devices). The UDB (User Data Base) tab on the diagnostics page, provides information on Ethernet activity. J1939 The J1939 tab on the diagnostics page, provides information on J1939-bus activity. Software setup | Zeus3 Glass Helm Installation Manual...
  • Page 34 This list allows control over which sentences need to be transmitted to other devices from the NMEA 0183 port. Due to the limited bandwidth of NMEA 0183 it is desirable to only Software setup | Zeus3 Glass Helm Installation Manual...
  • Page 35 Ú Note: Other MFDs cannot decode this information back to NMEA 0183, to use the data as a source. To share data a physical NMEA 2000 or NMEA 0183 connection is still required. Software setup | Zeus3 Glass Helm Installation Manual...
  • Page 36: 3Rd Party Support

    Enabling this causes the Zeus³ Glass Helm to synchronize its backlight setting with that of any CZone Display Interfaces set up to share backlight settings. Ú Note: CZone Config also needs to have the Zeus³ Glass Helm set as a controller. 3rd party support | Zeus3 Glass Helm Installation Manual...
  • Page 37: Appendix

    Appendix Accessories The most up-to-date accessories list is available at: www.bandg.com Appendix | Zeus3 Glass Helm Installation Manual...
  • Page 38: Supported Data

    AIS Class B Extended Position Report 129041 AIS aids to Navigation 129283 Cross Track Error 129284 Navigation Data 129539 GNSS DOPs 129540 AIS Class B Extended Position Report 129794 AIS aids to Navigation Appendix | Zeus3 Glass Helm Installation Manual...
  • Page 39 GNSS DOPs 129540 GNSS Sats in View 130074 Route and WP Service - WP List - WP Name & Position 130306 Wind Data 130310 Environmental Parameters 130311 Environmental Parameters 130312 Temperature 130577 Direction Data Appendix | Zeus3 Glass Helm Installation Manual...
  • Page 40 TX / RX - AIS / DSC Receive Ú Note: AIS sentences are not bridged to or from NMEA 2000. TX / RX - MARPA Transmit Ú Note: These are only output sentences. Appendix | Zeus3 Glass Helm Installation Manual...
  • Page 41 Transmission Current Gear 127493 127 / 65272 Transmission Oil Pressure 127493 177 / 65272 Transmission Oil Temperature 127493 Ú Note: The unit will act as a gateway and resend received J1939 PGN/SPN over NMEA 2000. Appendix | Zeus3 Glass Helm Installation Manual...
  • Page 42: Technical Specifications

    Dimensions (W x H x D) Refer to "Dimensional drawings" on page 44 Weight (display only) 16" unit 3.9 kg (8.6 lbs.) 19" unit 4.8 kg (10.5 lbs.) 24" unit 7.8 kg (17.2lbs.) Compass Safe Distance - Metric, imperial 50 cm Appendix | Zeus3 Glass Helm Installation Manual...
  • Page 43 Mounting type Panel mount or bracket (optional accessory) Appendix | Zeus3 Glass Helm Installation Manual...
  • Page 44: Dimensional Drawings

    Dimensional drawings 16" . mm 19" . mm 24" . mm Appendix | Zeus3 Glass Helm Installation Manual...

Table of Contents