Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Crestron CWD6671
Summary of Contents for Crestron CWD6671
- Page 1 Crestron CWD6671 Two-Way RF Transceiver Module Operations Guide...
- Page 2 This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2009 Crestron Electronics, Inc.
- Page 3 Crestron CWD6671 Two-Way RF Transceiver Module Contents Two-Way RF Transceiver Module: CWD6671 ..........1 Introduction ..........................1 Functions and Features ....................1 Specifications ......................2 Physical Description....................2 Industry Compliance ....................4 Setup ............................7 Hardware Hookup ....................... 7 End Product Labeling ....................8 Documentation ......................
-
Page 5: Two-Way Rf Transceiver Module: Cwd6671
The module receives RF signals from one or more Crestron devices and can transmit these signals over the air or over a cable run for further processing (depending on the application). -
Page 6: Operations Guide - Doc
Two-Way RF Transceiver Module Crestron CWD6671 Specifications The table below is a summary of specifications for the CWD6671. Specifications of the CWD6671 SPECIFICATION DETAILS Power Requirements 0.22 Watts (3.3VDC @ 0.67A) Operating Frequency 2400 MHz to 2483.5 MHz (802.15.4 compliant) Operating Ranges¹... - Page 7 13 11 9 7 5 3 Power/I-O Pinout Signals Pin # Signal Pin # Signal +5V (NU) SSEL_INT +5V (NU) SCLK WAKE +3.3V MISO Link Activity MOSI 3.3V HOST_INT RF_RESET_N Two-Way RF Transceiver Module: CWD6671 • 3 Operations Guide - DOC. 6834...
-
Page 8: Industry Compliance
Industry Compliance Labeling Requirements If the FCC ID on the CWD6671 is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID:... - Page 9 If any cable or antenna other than that provided with the CWD6671 is used, then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for reevaluating the end product (including the transmitter) and obtaining a separate FCC authorization.
- Page 10 FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for reevaluating the end product (including the transmitter) and obtaining a separate FCC authorization. 6 • Two-Way RF Transceiver Module: CWD6671 Operations Guide - DOC. 6834...
-
Page 11: Setup
Hookup Connections for CWD6671 For more information on these connectors, refer to “Ports” on page 3. Two-Way RF Transceiver Module: CWD6671 • 7 Operations Guide - DOC. 6834... -
Page 12: End Product Labeling
20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.” 8 • Two-Way RF Transceiver Module: CWD6671 Operations Guide - DOC. 6834... - Page 13 Crestron CWD6671 Two-Way RF Transceiver Module This page intentionally left blank Two-Way RF Transceiver Module: CWD6671 • 9 Operations Guide - DOC. 6834...
- Page 14 10 • Two-Way RF Transceiver Module: CWD6671 Operations Guide - DOC. 6834...