Advertisement
INSTRUCTIONS FOR
INSTALLATION AND OPERATION
MODEL V7FCD FIXED MINI DOME
The information in this manual covers the installation
and maintenance of the V7FCD Fixed-Ceiling Omnis-
can. Read these instructions through completely before
performing any installation procedures.
This unit should be installed by a qualified technician
using approved materials and wiring practices in accord-
ance with national, state, and local wiring codes.
The V7FCD Omniscan is designed to accommodate
small monochrome and color solid-state cameras for
installations where discreet surveillance is a necessity.
This unit is designed to be mounted in a drop ceiling,
the factory. It is the carrier's responsibility to deliver the
equipment in the same condition as it left the factory.
2.1.1 INSPECTION FOR VISIBLE DAMAGE
Immediately inspect the cartons upon delivery. Make a
note of any visible damage on all copies of the carrier's
freight bill.
Make sure the carrier's agent (the person making the
delivery) signs the note on all copies of the bill. If the agent
does not have claim forms, contact the carrier's office.
WARNING: TO PREVENT RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
Product specifications subject to change without notice.
Copyright 0 1998 Vicon Industries Inc. All rights reserved.
VICON INDUSTRIES INC. 89 ARKAY DRIVE, HAUPPAUGE, N.Y. 11788
TOLL FREE: l-800-645-91 16
1. INTRODUCTION
2. INSTALLATION
2.1 Unpacking and Inspection
UK: 44/(O) 1489/566300
l
l
although it may be installed in other types of ceilings.
A mounting rail option (Model V3380MR) is available
for installations requiring additional support, and a steel
ceiling panel option (Model V7FCP) is available to
replace the existing ceiling tile.
The viewing dome of the V7FCD is tinted neutral gray
overall, and the interior surface is painted flat black,
except for a narrow viewing strip. The combination of
tinted plastic and the painted interior makes it virtually
impossible to see into the dome. Attached by clips and
nuts, the dome is easily removed to simplify installation
and service.
2.1.2 INSPECTION FOR CONCEALED
DAMAGE
As soon as possible after delivery, unpack the unit and
inspect it for concealed damage. Do not discard the carton
or packing materials. If the unit is damaged, contact the
carrier immediately and request forms for filing a damage
claim. Make arrangements for a representative of the
carrier to inspect the damaged equipment.
If the equipment must be returned for repair, follow the
Shipping Instructions at the end of this manual.
Vicon and its logo are registered trademarks of Vicon Industries Inc.
TEL: 516-952~CCTV
l
INFOFAX: l-800-287-1207
l
Vicon part number 8006-8851-00-00
FAX: 516-951-CCTV
l
WORLD WIDE WEB:
Advertisement
Table of Contents
Related Manuals for Vicon V7FCD
Summary of Contents for Vicon V7FCD
- Page 1 This unit should be installed by a qualified technician using approved materials and wiring practices in accord- The viewing dome of the V7FCD is tinted neutral gray ance with national, state, and local wiring codes. overall, and the interior surface is painted flat black, except for a narrow viewing strip.
-
Page 2: Important Safeguards
16. Overloadin Do not overload wall outlets and extension cords 6. Attachments - Do not use attachments not recommended by Vicon as this can resu t In a risk of fire or electric shock. as they may cause hazards. -
Page 3: Upper Housing
The ceiling tile used in this procedure CAUTION: must be strong enough to support the combined Lift the upper housing of the V7FCD into the ceiling weight of the V7FCD and the camera/lens assembly. area and rest it on one of the tiles adjacent to the Although the V7FCD is not heavy [upper housing opening it is going to occupy. - Page 4 The V3380MR mounting rail kit may be used in con- junction with either an existing ceiling tile or the V7FCP 2. Lift the upper housing of the V7FCD into the ceiling ceiling panel option. If an existing ceiling tile is to be...
-
Page 5: Maintenance
3. MAINTENANCE inside surface and the entire exterior surface of the dome. The V7FCD Omniscan requires no maintenance other than occasional cleaning of the viewing strip area of the 3.1 Handling and Cleaning Procedures for Acrylic Domes 3. - Page 6 Excessive pressure or rubbing on the CAUTION: Scratches or other surface blemishes in the dome dome’s surface can cause permanent scratches material that are located in the viewing area may that may render the dome unusable. possibly be removed by applying a nonabrasive wax to the affected area with a soft cleaning cloth.
-
Page 7: Shipping Instructions
Name and address of the company return- (R.A.) at one of the locations listed below. Record ing the unit the name of the Vicon employee who issued the b . Name of the Vicon employee who issued R.A. the R.A.
Need help?
Do you have a question about the V7FCD and is the answer not in the manual?
Questions and answers