Krups Nescafé Dolce Gusto Lumio KP130110 Service Manual
  1. Manuals
  2. Brands
  3. Krups Manuals
  4. Coffee Maker
  5. Nescafe Dolce Gusto Lumio KP130110
  6. Service manual

Krups Nescafé Dolce Gusto Lumio KP130110 Service Manual

Beverage center
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
SERVICE MANUAL
BEVERAGE CENTER
LUMIO
Version 1.1 en
1/
28.09.2017

Advertisement

Table of Contents
loading

Related Manuals for Krups Nescafé Dolce Gusto Lumio KP130110

Summary of Contents for Krups Nescafé Dolce Gusto Lumio KP130110

  • Page 1 SERVICE MANUAL BEVERAGE CENTER LUMIO Version 1.1 en 28.09.2017...

  • Page 2: Table Of Contents

    C O N T E N T S Main components ....................6 Overview of external parts.................... 6 Overview of internal parts..................... 7 Overview of extraction head parts................9 Rating plate ......................... 11 Breville rating plate (example)................12 Water circuit........................ 13 Schematic diagram....................
  • Page 3 Replace power cord ....................53 Assembly tips......................54 Replace water tank connector with filter ..............55 Assembly tip......................56 Remove and replace top parts ..................57 Remove HMI module ....................57 Remove housing back ....................58 Assembly tips......................58 Remove housing left and right ................59 Assembly tip......................61 Replace HMI module ....................62 Assembly tips......................63 Replace head magnet.....................64...
  • Page 4 Capsule holder assembly (part no. 9110420000)............. 105 Housing right (part no. 3011449200/red, 3011440200/white, 3011449100/black) ... 106 Housing left (part no. 3011449400/red, 3011440300/white, 301144933/black)..107 Housing back (part no. 3011440400) ............... 108 Support frame (part no. 3011440000) ..............109 Main frame (part no. 3011447400) ................110 Component frame (part no.
  • Page 5 P R E F A C E The purpose of this Service Manual is to provide the service personnel with all neces- Please keep this sary information with regards to correct handling, maintenance and repair of the Lumio manual together beverage center.

  • Page 6: Main Components

    M A I N C O M P O N E N T S M A I N C O M P O N E N T S Overview of external parts The numbers are 12 13 not consistent with the position numbers of the spare parts list.

  • Page 7: Overview Of Internal Parts

    M A I N C O M P O N E N T S Overview of internal parts Sectional view from the back. 1. Valve switch 7. Power PCB The numbers are 2. Cold water pressure hose 8. NTC temperature sensor not consistent with 3.
  • Page 8 M A I N C O M P O N E N T S Building block 1. Building block support 8. Hot water outlet 2. Thermoblock 9. NTC connector 3. Protective ground terminal 10. Building block connector 2 4. Thermofuses (2x) with fuse sheet 11.

  • Page 9: Overview Of Extraction Head Parts

    M A I N C O M P O N E N T S Overview of extraction head parts The numbers are not consistent with the position numbers of the spare parts list. 1. Connection hose to water outlet on 5.
  • Page 10 M A I N C O M P O N E N T S Capsule holder 1. Lid 8. Steel axis 2. Sealing rubber (bonded to lid) 9. Spring right 3. Steel needle 10. Steel axis left / right 4. Capsule holder 11.

  • Page 11: Rating Plate

    M A I N C O M P O N E N T S Rating plate View from below. TYPE KP130 Groupe SEB – 53104 Mayenne www.krups.com France 220-240V~ 50/60Hz 1340-1600W Do not immerse in water MADE IN CHINA xxxxxxxxx REF: KP130110 /7Z0- WWYY The two-part rating plate is laser engraved on the bottom of the coffee machine.

  • Page 12: Breville Rating Plate (Example)

    M A I N C O M P O N E N T S TYPE KP130 Explanation of the Trade reference rating plate - right Groupe SEB – 53104 Mayenne part. France Company address Eurasian conformity mark Data matrix code Bar code reference CCCCCC = Serial number: 0 - 999999 X = Colour code:...

  • Page 13: Water Circuit

    M A I N C O M P O N E N T S Water circuit Schematic diagram The numbers are not consistent with the position numbers of the spare parts list. 1. Water tank 7. Cold water valve 2. Water tank connector with valve 8.

  • Page 14: Circulation Model

    M A I N C O M P O N E N T S Circulation model The numbers are consistent with the schematic diagram. 11, 12 1. Water tank 7. Cold water pressure tube 2. Water tank connector with valve 8.

  • Page 15: Technical Data

    M A I N C O M P O N E N T S Technical data Mains voltages Europe (LT, EE, LV, RU, NO, SE, FI, DK, ES, IT, CH, UK, DE, AUS, ZA) ..230 V, 50 Hz US / CA ...................... 120 V, 60 Hz Mexico....................
  • Page 16 M A I N C O M P O N E N T S Capacities Water tank ........................0.9 l Drip tray....................... max. 110 ml Environmental conditions Operating temperature range ..........5 °C - 45 °C (41 °F - 113 °F) Storage temperature range ........

  • Page 17: Dimensions And Weight

    M A I N C O M P O N E N T S Dimensions and weight Dimensions in mm. Maximum dimensions (width × depth × height)......176 × 222 × 368 mm Power cord length ....................0.8 m Weight of machine (without water)............approx. 2.5 kg Lumio service manual...
  • Page 18 M A I N C O M P O N E N T S Distances between bottom of extraction head and adjustable drip tray Dimensions in mm. Drip tray settings appropriate for: Espresso cup ...............max 70 mm high Mug ................max. 117 mm high Tall glass ..............max.

  • Page 19: Operating

    O P E R A T I N G O P E R A T I N G Machine status An automatic self-test is performed after switching on the machine. Operating modes and detected failures are indicated by the indicator light as listed in the The indicator light following table: is embedded in the...

  • Page 20: Hmi Module

    O P E R A T I N G HMI module The HMI module consists of selector wheel indicator light bar display, green illuminated. Bar display The stated filling 300 ml quantities may vary by ± 10 %. 230 ml 173 ml 146 ml 130 ml...

  • Page 21: Eco Mode

    O P E R A T I N G • Push and release selection lever. • Open locking handle. Remove or insert capsule holder. Eco mode 1 min After 1 minute of non-usage, the machine switches to the eco mode automatically. In eco For longer periods mode only the head PCB and building block PCB are functional in a limited way, while of standstill (e.g.

  • Page 22: Preparation For First Use

    O P E R A T I N G Preparation for first use The new machine has to be rinsed properly before first use according to the following sequence: 1. Rinse water tank manually with fresh 4. Open locking handle. drinking water.
  • Page 23 O P E R A T I N G STOP 17. Set bar display to level 7 with 20. Machine stops rinsing and indicator To stop the rinsing selector wheel. light blinks red for a few seconds. at any time, turn the 18.

  • Page 24: Preparing A Beverage

    O P E R A T I N G Preparing a beverage 1. Check if water tank contains enough 4. Open locking handle. Users allergic to fresh drinking water. 5. Pull out capsule holder. dairy products: 2. Adjust drip tray position depending 6.

  • Page 25: Special Precaution To Prevent Water Splashes

    O P E R A T I N G 16. For beverages using 2 capsules: 18. Open locking handle. Risk of burning Repeat brewing procedure with 19. Pull out capsule holder and remove from hot capsule! second capsule. used capsule. Do not touch the cap- 17.

  • Page 26: Empty Fluid System For Shipping

    O P E R A T I N G Empty fluid system for shipping For shipping a machine, it is important to empty the fluid system. Machine switches 1. Remove and empty water tank and 3. Open locking handle and remove on automatically.

  • Page 27: Troubleshooting

    T R O U B L E S H O O T I N G T R O U B L E S H O O T I N G Read error code Refer to error code 1. Push selection lever to right position 3.

  • Page 28: Error Code List

    T R O U B L E S H O O T I N G Error code list Bar display Error Error description Remark No error Not reported in memory. ─ Nothing active Let thermoblock cool down in eco mode for half an hour.

  • Page 29: Troubleshooting Checklist

    T R O U B L E S H O O T I N G Troubleshooting checklist The checklist enables you to rapidly locate faults on the machine and to initiate appropriate repair action. Follow the check procedure. Repair any faults found and check if the machine is operating perfectly. Check Further action / Symptoms...
  • Page 30 T R O U B L E S H O O T I N G Check Further action / Symptoms Action / repair work procedure repair work 3.1 Inside of extraction head YES - Clean with a damp cloth soiled (capsule holder NO - Go to point 3.2 removed)? YES - Clean and make pres-...
  • Page 31 T R O U B L E S H O O T I N G Check Further action / Symptoms Action / repair work procedure repair work YES - Replace NTC YES - a) NTC temperature temperature sensor  p. 34 sensor (32) defective? NO - Go to point b) 6.2 Indicator light flashes red...
  • Page 32 T R O U B L E S H O O T I N G Check Further action / Symptoms Action / repair work procedure repair work YES - Descale fluid system YES - a) Fluid system scaled? ( p. 89) NO - Go to point b) 9.1 Hot water temperature is too low (less than 70°C /...
  • Page 33 T R O U B L E S H O O T I N G Check Further action / Symptoms Action / repair work procedure repair work YES - Go to point b) YES - a) Drip tray and drip grid NO - Assemble correctly or are inserted correctly 11.1 Check vibrations while...

  • Page 34: Repair

    R E P A I R R E P A I R General This chapter contains special safety and assembly notes. Non-observance of the safety and assembly notes can lead to injuries and damages! • The disassembly and repair procedures are presented as step by step instructions. •...

  • Page 35: Tools And Repair Accessories

    R E P A I R Tools and repair accessories With the following tools, all described disassembly and repair work can be done: Tools and consumable material Applications Torque screwdriver with tamper 1 screw for HMI module (1) A pin-torx screw proof security Torx bit T9 6 screws for base cover (10) head of a security...

  • Page 36: Screw Tightening Torques

    R E P A I R Screw tightening torques The max. screw Screw connection / screw type Torque Position tightening torque indicated must not be exceeded. The torque val- ues for plastic HMI module fixing screw (1x) 5.0 ± 0.5 kgf·cm parts are only applica- 49.0 ±...

  • Page 37: Simple Repair Work

    R E P A I R Screw connection / screw type Torque Position Bottom part fixing screws (6x) 5.0 ± 0.5 kgf·cm 49.0 ± 4.9 Ncm TX9 safety pin 4.3 ± 0.4 lbf-in dia. 2.9 x 13 Power cord: Strain clip fixing 4.0 ±...

  • Page 38: Disassembly Preparations

    R E P A I R Disassembly preparations Unplug machine from the mains before disassembly - appliance must be isolated! 1. Wait until machine is in eco mode and then unplug power cord. The cleaning needle 2. Remove and empty water tank (13). can remain in the 3.

  • Page 39: Remove And Replace Bottom Parts

    R E P A I R Remove and replace bottom parts Remove base cover Use a repair stand for easy disassem- bly and parts replace- ment. 1. Insert blade of a small screwdriver into gap between base cover (10) and bottom part (9) like shown.

  • Page 40: Assembly Tips

    R E P A I R 4. Lift base cover (10) at the rear to release both hooks. 5. Release wedge and hooks at the other end of base cover as already described. Assembly tips • Check base cover for broken latches. Replace base cover if necessary Lumio service manual...

  • Page 41: Remove Bottom Part

    R E P A I R Remove bottom part 6. Loosen 6 screws (TX9 with safety pin). 7. Insert blade of a small screwdriver into gap between bottom part (9) and compo- nent frame (8) like shown. 8. Swivel screwdriver upwards to release wedge. 9.

  • Page 42: Replace Flow Meter

    R E P A I R Replace flow meter 1. Unplug flow meter connector from building block PCB (part of building block 15). 2. Press down latch on flow meter (22) with your thumb. 3. Pull off silicone elbow (21) and water tank connector (20) from flow meter. Lumio service manual...
  • Page 43 R E P A I R Use a small flathead screwdriver to lever 4. Insert blade of a flat screwdriver under flow meter. the flow meter connec- 5. Swivel screwdriver to lift flow meter (22) until its locking pin and orientation pin are tor out of its socket.

  • Page 44: Assembly Tips

    R E P A I R Assembly tips • Always replace a removed flow meter (22) with a new one. Risk of malfunc- tion! Do not interchange sil- icone elbow and tube of water tank connec- tor by mistake. • Connect tubes of water tank connector (20) and silicone elbow (21) to flow meter (22) as shown.

  • Page 45: Replace Pump

    R E P A I R Replace pump Depending on the supplier, the body of the pump can have different colours. 1. Unplug flat receptacle of white pump wire from building block PCB (part of building Use flat nose pliers block 15).
  • Page 46 R E P A I R 3. Pull both rubber supports (part of pump 19) out of the guides in component frame Use a flathead (8) alternately. screwdriver for easy removal. 4. Unplug flat receptacle with brown wire from pump terminal. Use flat nose pliers for easy removal.
  • Page 47 R E P A I R 5. Check condition of pressure hoses on pump outlet: Remove hose clip(s) (26) and pull off old, brittle pressure hose(s) from pump (19). 6. Check condition of pump outlet. Discard a dirty, clogged or leaky pump outlet together with a defect pump.

  • Page 48: Assembly Tips

    R E P A I R Assembly tips • Always replace pressure hoses that have been pulled off together with the related hose clips (26). • Check according to illustration position of pump outlet mounting position of hose clips (26) on pump outlet. •...

  • Page 49: Replace Ntc Temperature Sensor

    R E P A I R Replace NTC temperature sensor 1. Unplug NTC connector from building block PCB (part of building block 15). Use a small flathead 2. Remove spring clip with pointed pliers and replace NTC temperature sensor (32). screwdriver to lever the NTC connector out of its socket.

  • Page 50: Replace Building Block

    R E P A I R Replace building block 1. Unplug following connectors from building block PCB (part of building block 15): Use a small flathead • Building block connector 1 (a) screwdriver to lever • Building block connector 2 (b) the connectors out of •...

  • Page 51: Assembly Tips

    R E P A I R 6. Release latch and carefully remove building block (15) from component frame (8). 7. Finally, remove the power cord  p. 53. Assembly tips • For handling a new building block (15), the service technician should be earthed Risk of damage! using an earthing strap.
  • Page 52 R E P A I R • For cable and wire routing and connection: Refer to photograph and wiring diagram  p. 69. • Make sure that the receptacles are in the correct position by slightly pulling them back. Lumio service manual...

  • Page 53: Replace Power Cord

    R E P A I R Replace power cord The removal of the power cord is an integrated part of the procedure for replacing the building block. Prerequisites: • The flow meter (22) is removed  p. 42. • The building block (15) is removed from the component frame (8)  p. 50. Procedure: 1.

  • Page 54: Assembly Tips

    R E P A I R Assembly tips • When inserting flat receptacles of the power cord, make sure that the special connector latching shows to the outside of the building block PCB. • Insert wires of power cord (37) into cable guide on building block PCB cover. •...

  • Page 55: Replace Water Tank Connector With Filter

    R E P A I R Replace water tank connector with filter Prerequisites: • The flow meter (22) is removed  p. 42. • The building block (15) is removed from the component frame (8)  p. 50. • Housing right (4) and housing left (5) are removed  p. 59. •...

  • Page 56: Assembly Tip

    R E P A I R Assembly tip • Check that the filter (25) is inserted in the water tank connector (20) correctly. Make sure that you can see all the snaps from the connector above the filter. Otherwise the water tank can leak or the water tank valve does not open. Lumio service manual...

  • Page 57: Remove And Replace Top Parts

    R E P A I R Remove and replace top parts Always remove the covers in the given Remove HMI module order of this chapter. The HMI module can only be replaced after removing housing back and hous- ing left. 1.

  • Page 58: Remove Housing Back

    R E P A I R Remove housing back 1. Insert blade of a screwdriver into gap at one side of housing back (14) and release the latch. 2. Lift housing back to release both pegs at the bottom. 3. Insert blade of screwdriver at the other side and release the second latch. 4.

  • Page 59: Remove Housing Left And Right

    R E P A I R Remove housing left and right 1. Loosen screw (TX10 with safety pin) below clamp handle (16) - see detail. 2. Loosen 3 screws (TX10 with safety pin). 3. Insert blade of screwdriver into gap and separate the connection part of housing right (4) from housing left (5).
  • Page 60 R E P A I R 4. Use a screwdriver to remove the lug of housing left (5) from extraction head (2). 5. Pull off housing left from main frame (7). Lumio service manual...

  • Page 61: Assembly Tip

    R E P A I R 6. Pull off housing right (4) from main frame (7). Assembly tip • Make sure that connection parts of housing right (4) are snapped in housing left (5). Lumio service manual...

  • Page 62: Replace Hmi Module

    R E P A I R Replace HMI module 1. Unplug all connectors from head PCB (part of HMI module 1): Use a small flathead • Reed switch connector screwdriver to lever • Valve switch connector the connectors out of •...

  • Page 63: Assembly Tips

    R E P A I R Assembly tips • For handling a new HMI module (1), the service technician should be earthed using Risk of damage! an earthing strap. The head PCB is sensible to electrostatic discharge (ESD) - use safety measures.

  • Page 64: Replace Head Magnet

    R E P A I R Replace head magnet 1. If not already done, unplug head magnet connector. 2. Loosen 2 crosshead screws and remove magnet holder. 3. Pull head magnet (30) out of support. Lumio service manual...

  • Page 65: Replace Clamp Handle

    R E P A I R Replace clamp handle 1. Loosen 2 crosshead screws and remove locking handle (16). Assembly tip • Check free movement of the locking handle after reassembly. Lumio service manual...

  • Page 66: Replace Extraction Head

    R E P A I R Replace extraction head Prerequisites: • The cold water pressure hose is removed from the pump outlet. • The hot water pressure hose is removed from the thermoblock. • The head connector 1# is unplugged from the head PCB. The wires of this connector are pulled out of the cable guides on the extraction head (2).

  • Page 67: Assembly Instructions And Tips

    R E P A I R Assembly instructions and tips • Insert pressure hoses of new extraction head (2) into hose holders on top of the support frame (6, circled in red). • Insert support frame into main frame (7) and fasten it with 2 screws (TX10 with safety pin).
  • Page 68 R E P A I R • Pull cold water pressure hose through hose support on component frame (8). • For wire routing and connection to head PCB: Refer to photograph and wiring diagram  p. 69 Lumio service manual...

  • Page 69: Wiring Diagram (Eu/Usa/Japan)

    W I R I N G D I A G R A M ( E U / U S A / J A P A N ) W I R I N G D I A G R A M ( E U / U S A / J A P A N ) Power Cord (Power plug varies depending on country version) Pump...

  • Page 70: Final Tests

    F I N A L T E S T S F I N A L T E S T S The following tests guarantee the correct function of the machine: 1. Heating up time 2. Flow rate (at 8 bar) / water temperature 3.

  • Page 71: Heating Up Time

    F I N A L T E S T S Heating up time 1. Connect power plug to mains power 3. Measure heating up time until indi- socket. cator light stops blinking red and 2. Turn selector wheel to switch on turns to steady green.

  • Page 72: Pressure Test / Flow Rate (At 8 Bar) / Water Temperature

    F I N A L T E S T S Pressure test / flow rate (at 8 bar) / water temperature 1. Open locking lever. 3. Insert dummy capsule into capsule 2. Remove and open capsule holder. holder. Realign dummy 4.
  • Page 73 F I N A L T E S T S 11. Place a recipient under test device. 12. Ensure that a precise electronic ther- mometer (F) is available. End of test device assembly. The water for this 11.5 bar function test must leakage be fresh, potable water.
  • Page 74 F I N A L T E S T S 30 sec 17. Wait until machine is in eco mode. 19. Release the pressure by opening the Then unplug coffee machine. pressure control valve completely. 18. Watch manometer for 30 sec. 20.
  • Page 75 F I N A L T E S T S 11.5 bar leakage 14.5 bar no leakage approx. 3 mm 26. Measure hot water temperature with 27. Close pressure control valve progres- electronic thermometer: Place sively to reach Pmax. temperature sensor in water flow Maximum pressure must be within approx.

  • Page 76: Leakage Check

    F I N A L T E S T S Summary The final tests are passed if flow rate is between 75 to 125 ml within 30 sec (150 - 250 ml/min) water temperature is between 80 °C to 90 °C (176 °F to 194 °F) maximal pressure is between 11.5 to 14.5 bars pressure drop is less than 1.5 bars within 30 sec no water is leaking (extraction head, housing bottom etc.).
  • Page 77 F I N A L T E S T S 3. Insert capsule holder with dummy 6. Plug in resp. switch ON coffee capsule and test device  p. 72. machine. 4. Insert water tank. 7. When machine is ready, set bar 5.
  • Page 78 F I N A L T E S T S 12. After inspection, release remaining If no leak could be detected, repeat the pressure by opening the pressure leakage check with cold water: control valve completely. 13. Set bar display back to level 7 with selector wheel.

  • Page 79: Leakage Check For Bottom Part

    F I N A L T E S T S 18. Remove and empty container. 20. Unplug coffee machine. 19. Remove capsule holder and detach 21. Proceed with repair or reassemble test device. extraction head. Leakage check for bottom part This leakage check is for pressurized components only.
  • Page 80 F I N A L T E S T S 3. Place coffee machine on a heat 5. Insert capsule holder with dummy resistant, electrical insulating capsule and test device  p. 72. surface. 6. Insert water tank. 4. Secure coffee machine against tilting 7.
  • Page 81 F I N A L T E S T S 14. Perform a visual inspection of all 15. After inspection, release remaining components under pressure. pressure by opening the pressure control valve completely. 16. Remove and empty container. 18. Proceed with repair or reassemble 17.

  • Page 82: Final Inspections

    F I N A L I N S P E C T I O N S F I N A L I N S P E C T I O N S General Legal situation Repair centres can be legally obligated to ensure the safety and physical integrity of the Check the legal sit- user/consumer by national regulations and standards.

  • Page 83: Safety Instructions

    F I N A L I N S P E C T I O N S Safety instructions WAR NI NG Danger of electric shock! Risk of damage to the coffee machine. High test voltage - hazardous situations can arise if a wrong test is selected or a test is executed incorrectly.

  • Page 84: Insulation Resistance Test

    F I N A L I N S P E C T I O N S Insulation resistance test This test verifies the insulation resistance between the protective earthing conductor of the coffee machine and the phase/ neutral conductor of the coffee machine. of all conductive and touchable parts of the coffee machine (with the help of a test probe).
  • Page 85 F I N A L I N S P E C T I O N S 8. Open locking lever and pull out capsule holder. 9. Touch marked screw inside of extraction head with test probe. 10. Press start button (C) and read off displayed resistance. The insulation resistance must be higher than 2.0 Mega Ohm with a test voltage of 500 VDC.

  • Page 86: Earth Leakage Current Test

    F I N A L I N S P E C T I O N S Earth leakage current test This test measures the leakage current in the protective earth conductor when the coffee Depending on the machine is switched on. test equipment, dif- ferent measuring meth- ods are possible.

  • Page 87: Maintenance

    M A I N T E N A N C E M A I N T E N A N C E Cleaning Clean capsule holder 1. Open locking handle. 3. Open capsule holder. 2. Remove capsule holder. 4. Put capsule holder in dishwasher. Clean capsule holder without dishwasher Clean all gaps and hinges on the cap-...

  • Page 88: Deblock Injector

    M A I N T E N A N C E Deblock injector Solid residues in the water circuit can block the injector in the capsule holder lid The Cleaning nee- completely. An example is the development of calcium particles if the machine is not dle is not assembled descaled periodically.

  • Page 89: Descaling

    M A I N T E N A N C E Descaling If the colour of the indicator light changes from green to orange ( p. 19), the coffee machine has to be descaled. Caution! Only use appropriate descaling solution that suits for coffee machine - never use Vinegar! •...

  • Page 90: Descaling Procedure

    M A I N T E N A N C E Descaling procedure The descaling pro- cedure takes 650 ml approx. 15 min. 1. Remove and empty water tank. 2. Mix 650 ml fresh, drinking water with descaler in a measuring cup. 3.
  • Page 91 M A I N T E N A N C E Make sure the machine is switched off (no indicator light) before entering the des- caling mode. 1 min 10 sec 9. Wait for approx. 1 minute until 10. Push selection lever to the right and machine switches off automatically hold it in “HOT”...
  • Page 92 M A I N T E N A N C E If the container needs to be emp- tied, push the selection lever to the middle posi- tion. To continue with descaling, push the selec- tion lever back into the previous position.

  • Page 93: Clean Machine

    M A I N T E N A N C E Clean machine 1. Remove and empty water tank. 5. Remove and empty drip tray. 2. Clean water tank with a clean food- 6. Clean drip grid and drip tray with a safe brush and washing-up liquid as clean food-safe brush.
  • Page 94 M A I N T E N A N C E 19. Reinsert capsule holder and close 23. Clean machine with a soft damp locking handle. cloth. 20. Remove and empty water tank. 24. Dry it afterwards with a soft dry cloth. 21.

  • Page 95: Packing Instructions

    M A I N T E N A N C E Packing instructions Risk of damage! • Wrap the coffee machine in a plastic foam bag to avoid scratches during transportation. • Use a new packaging for shipment if necessary. •...
  • Page 96 M A I N T E N A N C E 8. Lay power cord into recess. 10. Close flap with handle first. 9. Put EPS trays into cardboard box. 11. Close side flaps. 13. Secure top lid with adhesive tape. 12.

  • Page 97: Spare Parts

    S P A R E P A R T S S P A R E P A R T S Spare parts drawing Lumio service manual...
  • Page 98 S P A R E P A R T S Spare parts drawing (contd.) Lumio service manual...
  • Page 99 S P A R E P A R T S Spare parts drawing (contd.) Lumio service manual...
  • Page 100 S P A R E P A R T S Spare parts drawing (contd.) Lumio service manual...

  • Page 101: Spare Parts List

    S P A R E P A R T S Spare parts list Pos. Part no. Part description Comment 9110431700 Assembly HMI black 9110431600 Assembly head with magnet, reed sensor, valve switch 9110420000 Assembly capsule holder 3011449200 Housing right 3011440200 Housing right white 3011449100...
  • Page 102 S P A R E P A R T S Pos. Part no. Part description Comment 1050003800 Head magnet Including wire and support 2030089100 Wire head to building block 2030088000 / Wire NTC 2030088900 2010155800 Power cord red 2010157300 Power cord red 2010155900 Power cord red 110V, BR...

  • Page 103: Annex

    A N N E X A N N E X HMI assembly (part no. 9110431700) Lumio service manual...

  • Page 104: Extraction Head Assembly (Part No. 9110431600)

    A N N E X Extraction head assembly (part no. 9110431600) Lumio service manual...

  • Page 105: Capsule Holder Assembly (Part No. 9110420000)

    A N N E X Capsule holder assembly (part no. 9110420000) Lumio service manual...

  • Page 106: Housing Right (Part No. 3011449200/Red, 3011440200/White, 3011449100/Black)

    A N N E X Housing right (part no. 3011449200/red, 3011440200/white, 3011449100/black) Lumio service manual...

  • Page 107: Housing Left (Part No. 3011449400/Red, 3011440300/White, 301144933/Black)

    A N N E X Housing left (part no. 3011449400/red, 3011440300/white, 301144933/black) Lumio service manual...

  • Page 108: Housing Back (Part No. 3011440400)

    A N N E X Housing back (part no. 3011440400) Lumio service manual...

  • Page 109: Support Frame (Part No. 3011440000)

    A N N E X Support frame (part no. 3011440000) Lumio service manual...

  • Page 110: Main Frame (Part No. 3011447400)

    A N N E X Main frame (part no. 3011447400) Lumio service manual...

  • Page 111: Component Frame (Part No. 3011447700)

    A N N E X Component frame (part no. 3011447700) Lumio service manual...

  • Page 112: Bottom Part (Part No. 3011447500)

    A N N E X Bottom part (part no. 3011447500) Lumio service manual...

  • Page 113: Base Cover (Part No. 3011450200/Red, 3011447600/White, 3011450100/White)

    A N N E X Base cover (part no. 3011450200/red, 3011447600/white, 3011450100/white) Lumio service manual...

  • Page 114: Drip Grid (Part No. 3011447900 + 301147640079)

    A N N E X Drip grid (part no. 3011447900 + 301147640079) Lumio service manual...

  • Page 115: Drip Tray (Part No. 3011447800)

    A N N E X Drip tray (part no. 3011447800) Lumio service manual...

  • Page 116: Water Tank (Part No. 9110419400)

    A N N E X Water tank (part no. 9110419400) Lumio service manual...

  • Page 117: Building Block Assembly (Part No. 9110434600/110V, 9110420600/220V)

    A N N E X Building block assembly (part no. 9110434600/110V, 9110420600/ 220V) Lumio service manual...

  • Page 118: Locking Handle (Part No. 3011449700)

    A N N E X Locking handle (part no. 3011449700) Lumio service manual...

  • Page 119: Pump Assembly (Part No. 9110434800/110V, 9110429900/220V)

    A N N E X Pump assembly (part no. 9110434800/110V, 9110429900/220V) Lumio service manual...

  • Page 120: Water Tank Connector Tube (Part No. 5040127700)

    A N N E X Water tank connector tube (part no. 5040127700) Lumio service manual...

  • Page 121: Silicone Elbow (Part No. 5040127800)

    A N N E X Silicone elbow (part no. 5040127800) Lumio service manual...

  • Page 122: Flow Meter Assembly (Part No. 9110420400)

    A N N E X Flow meter assembly (part no. 9110420400) Lumio service manual...

  • Page 123: Metal Sheet (Part No. 4030126500)

    A N N E X Metal sheet (part no. 4030126500) Lumio service manual...

  • Page 124: Flow Measurement Capsule For Final Tests

    A N N E X Flow measurement capsule for final tests Lumio service manual...

  • Page 125: Notes

    N O T E S N O T E S Lumio service manual...
  • Page 126 N O T E S Lumio service manual...

Table of Contents