Charging the headset ......................14 1. Charging in the base station charging slot ............15 2. Charging with the VMX OFFICE car charger unit ........... 15 3. Charging with a USB socket ..................15 4. Charging with the USB wall plug available as an accessory ....... 15...
Page 6
Wearing the headset ......................15 Switching on/off ........................16 Switching the headset on ....................16 Switching the headset off ....................16 Switching the base station off ..................16 Switching the base station on ..................16 Basic telephoning ........................ 16 Accepting a call via the base station ................16 Accepting a mobile phone call ..................
More room to move • Bluetooth 2.0: compatible with all Bluetooth 1.1, 1.2 and 2.0 devices that The VMX OFFICE system is a Class 2 support the “hands free” or “headset” mobile phone and Bluetooth device profile supporting the Bluetooth 2.0 standard.
– the 1 VMX OFFICE base station VMX OFFICE system is compatible with 1 phone connecting cable (already all types of speech-based mobile phone plugged to the base station) and Bluetooth devices.
· Operating elements PHONE button » PHONE LED ¿ AUX button ´ Headset AUX LED ¾ ² ¶ º volume button ² microphone volume control headset LED ¶ EU switch socket for power supply º ABC switch microphone boom ¾ PROGRAM button hook button speaker...
Button overview Buttons on the headset Buttons on the base station Button Function Page Button Function Page switch the headset activate connection to micro- PHONE on or off the device connected to · phone ¸ button the PHONE socket accept incoming call boom (usually fixed line end a call...
Setting up Type 1: Connecting the base station to a fixed line phone with a headset socket Upon delivery, the headset and the base station are pre-paired together. You just have to: 1. connect the base station to the mains 2.
Type 2: Type 3: Connecting the base station to a usual Connecting the base station to a fixed fixed line phone lined DHSG phone ¸ µ Connect the accessory cable (RJ 45 DHSG cable, not included) to the Disconnect the handset from your AUX/DHSG socket and to the DHSG fixed line phone, but leave it on the...
For multimedia purposes or voice over IP use a usual fixed line phone or no (internet telephony) you can connect phone at all the VMX OFFICE system to a computer. ¸ – to the PHONE socket if you use a...
(not included): Connect the USB plug to a USB socket Make sure the base station AUX of the computer. ´ is on. If not: Install the Sennheiser call control ¿ Press the AUX button software described ´ The AUX LED is on now.
To test the PC connection: When connecting a Sennheiser Commu- nications handset lifter (e.g. HSL 10, see Before testing make sure “Accessories” on page 22): the PC works accordingly. Connect the handset lifter to the ACC socket ¹. Make sure the base station AUX Install the microphone as described in ´...
To ensure optimum intelligibility, adjust – Start with the handset. the VMX OFFICE system to your phone as – Switch between the both by press- follows: · ing the PHONE button ·...
Limiting the speaker volume Pairing the headset The VMX OFFICE allows you to limit the Upon delivery, the headset and the base speaker volume of the headset to com- station are pre-paired together. You can ply with EU Directive 2003/10/EC.
The headset is turned on. The head- set LED starts flashing slowly in blue. 2. Charging with the VMX OFFICE car charger unit Put the headset on. The headset can be worn on either the left or right ear. Take off the headset.
Only if you use a handset lifter with ring Switching the base station on tone detection or the TCI 01 box or the Connect the base station to the mains Sennheiser Communications USB call con- trol software. as described on page 7.
To accept the call when the headset If an automatic handset not switched lifter is installed to your Open the microphone boom phone, it picks up the The headset is switched on and the handset automatically. call is answered immediately without Dial the number and talk.
most mobile phone or Bluetooth Advanced call management device microphones do. Press and hold the headset hook Toggling between calls via fixed line button until a confirmation beep is phone and mobile phone and vice versa heard. Toggling between fixed line phone calls Say the name of the other party.
Transferring a call from the headset to conditions like wall thickness, wall com- the mobile phone position etc. With a free line of sight, the trans- Please see your mobile phone manual on mission range of the base station is up how to transfer the call audio from the to 30 metres;...
We recommend to make a test call to Changing the speaker volume another person in the same office and to Press the volume button during a walk around during the call to find out if call. any areas are out of transmission range. The speaker volume is changed by If the headset leaves the transmission one step.
To un-mute the headset microphone: recognize the new headset unless they are paired as follows: Press the volume button The beeping stops. The microphone Press the program button quickly two works as usual. times. The base station is set to pairing »...
Maintenance and If problems occur ... care If no dial tone is heard: Make sure your office phone is set up If you do not want to use the headset for correctly according to its manual. a longer time: If no sound file is heard: Close the microphone boom ³.
Your legal rights guarantee period this against the seller, resulting from the Sennheiser Communications product is contract of sale, are not affected by this 24 months – for the battery 6 months – guarantee. from the date of purchase. Excluded...
Page 28
Sennheiser Communications A/S may This will help to protect the environment void the FCC authorization to operate this in which we all live.