GE T60 Instruction Manual page 664
Transformer protection system
Hide thumbs
Also See for T60:
- Instruction manual (796 pages) ,
- Communications manual (532 pages) ,
- Instruction manual (698 pages)
Table of Contents
Advertisement
DIFFERENTIAL CHARACTERISTIC TEST EXAMPLES
3.
When test setup is correct, the relay displays the following differential and restraint currents, and the element does
not operate.
Phase
Differential current (I
0 ∠0°
A
B
0 ∠0°
C
0 ∠0°
8.2.2.3 Minimum pickup test
Reduce the restraint current I
the pickup). This is obtained from I
the setting of Slope 1. Note that
where I
is an intersection of Minimum PKP and Slope 1 calculated as PKP/Slope 1 value.
ri
1.
Change the current magnitude as follows.
Winding 1
Phase
Single current (I
A
0 A ∠0°
B
0.15 A ∠0°
C
0.15 A ∠–180°
2.
Read the following differential and restraint current values from the T60 actual values menu.
Phase
Differential current (I
A
0 ∠0°
B
0.044 pu ∠0°
C
0.044 pu ∠0°
The relay does not operate since I
3.
Increase I
to 0.2 A. The differential current increases to I
1
4.
Verify that the Percent Differential element operates and the following are displayed in the actual values menu.
Phase
Differential current (I
A
0 ∠0°
B
0.136 ∠0°
C
0.136 ∠0°
8.2.2.4 Slope 1 test
8
Inject current in such a manner that the magnitude of I
intersection of the minimum PKP and Slope 1 and smaller than the Breakpoint 1 setting; that is,
1.
Change the current magnitudes as follows.
Winding 1
Phase
Single current (I
0 A ∠0°
A
0.48 A ∠0°
B
0.48 A ∠–180°
C
8-6
)
Phase
Restraint current (I
d
0 ∠0°
A
B
0.801 pu ∠–180°
C
0.801 pu ∠0°
to a value lower than 0.67 pu (the restraint corresponding to the intersection of Slope 1 and
r
= 0.1/0.15 = 0.67 pu, where 0.1 is the differential setting of minimum pickup, and 0.15 is
r
0 < I
r
Winding 2
)
Phase
Single current (I
1
A
0 A ∠0°
B
0.23 A ∠–180°
C
0.23 A ∠0°
)
Phase
Restraint current (I
d
A
0 ∠0°
B
0.275 pu ∠–180°
C
0.275 pu ∠0°
is still lower that the 0.1 pu
d
)
Phase
Restraint current (I
d
A
0 ∠0°
B
0.367 pu ∠–180°
C
0.367 pu ∠0°
is larger than the restraint current of 0.67 pu, corresponding to the
r
I
(intersection of Min PKP and Slope 1) < I
r
Winding 2
)
Phase
Single current (I
1
0 A ∠0°
A
1 A ∠–180°
B
1 A ∠0°
C
)
r
<I
ri
)
2
)
r
setting.
MINIMUM PICKUP
= 0.136 pu > Min PKP and I
d
)
r
(actual) < I
(Break 1)
r
r
)
2
T60 TRANSFORMER PROTECTION SYSTEM – INSTRUCTION MANUAL
CHAPTER 8: COMMISSIONING
Eq. 8-8
< 0.67 pu.
r
Eq. 8-9
Advertisement
Table of Contents
