Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Diamond Products CC190XL
Summary of Contents for Diamond Products CC190XL
-
Page 1: Concrete Saw
CONCRETE SAW OPERATOR’S MANUAL MODELS CC190XL, CC190PRO Dec 2016 Part #1802459... -
Page 3: Table Of Contents
Table of Contents Safety Precautions Safety Alerts -------------------------------------------------------------------------------------------- 4 Proposition 65 ------------------------------------------------------------------------------------------ 4 Spark Arrester Requirement ------------------------------------------------------------------------ 4 Respiratory Hazards ---------------------------------------------------------------------------------- 4 General Safety ----------------------------------------------------------------------------------------- 5 Battery and Electrical Safety ----------------------------------------------------------------------- 6 Blade Safety -------------------------------------------------------------------------------------------- 6 Blade Guard Safety ----------------------------------------------------------------------------------- 6 Fuel Safety ---------------------------------------------------------------------------------------------- 6 ... -
Page 4: Safety Precautions
Safety Precautions Proposition 65 WARNING Operate the CC190XL Concrete Saw and all of the Engine exhaust and some of its components according to this manual. Failure to constituents are known to the comply with and understand the following safety, State of California to cause... -
Page 5: General Safety
DO NOT: General Safety Read and understand all of the safety, Drop equipment, supplies, tools, etc., when operations, and maintenance instructions handling to help prevent injuries. provided in this manual prior to operating or Operate the saw around combustible materials servicing the saw. -
Page 6: Battery And Electrical Safety
Battery and Electrical Safety Inspect the blade flanges for damages, wear, and cleanliness. Clean or replace Ignitable explosive gases are dirty/damaged components immediately. emitted from the battery. DO DO NOT expose yourself or anyone NOT expose the battery to else to the direct line of the blade sparks or open flames. -
Page 7: Engine Safety
Let the engine cool prior to adding fuel. DO NOT operate the saw around combustible materials or fumes to prevent fires/explosions. Refer to the engine manual for recommended fuels. DO NOT touch the engine/muffler assembly with the engine running, and always let them Move the saw away from the refueling area cool down prior to touching or servicing the... -
Page 8: Belt Safety
hoisting the saw to prevent being crushed. Belt Safety Secure the appropriate hoisting cables, Turn off the engine and let the belts cool straps, and/or chains to the saw’s down prior to servicing them. designated lift points prior to hoisting. DO ... -
Page 9: Blade And Skid Plate Installation
6. Open engine throttle to full open position. Blade and Skid Plate Installation (All cutting to be at full throttle). Lower the front guide to the full down position by Remove the blade guard cover by turning pushing control lever forward. the two locking knobs counter-clockwise. -
Page 10: Maintenance Instructions
fasteners on this unit are metric. Please MAINTENANCE INSTRUCTIONS use the correct tool. 6. Cleaning: Use a wire brush to clean the 1. Lubricate the blade shaft bearings and blade guard assembly of any excess other fittings (wheels, bearings, etc.) concrete buildup after each use. - Page 11 Fuel Lines Regularly check fuel lines for damage and/or leaks and service as necessary. Refer to engine operator’s manual. Storing Complete the tasks listed below prior to storing the saw for longer time frames: Lower the saw completely to remove strain on the lifting mechanism.
-
Page 12: Troubleshooting
TROUBLESHOOTING CUT OF SAW IS SPALLING OR RAVELLING Check bottom of skid plate for burrs Check skid plate for excessive wear or gap around blade slot Check if skid plate is bent. Insure skid plate is mounted properly ... - Page 13 Engine is flooded. Adjust the choke per the engine owner’s Insure blade shaft rotates freely SAW PULLS TO ONE SIDE WHILE SAWING Check skid plate for burrs Check to see if rear and front guide is properly aligned with the center of the blade. ...
-
Page 14: References
Model Number Serial Number Appendix A Additional Resources 1. Diamond Products (www.diamondproducts.com) CC190XL Concrete Saw Parts List, Ohio 2015 A Guide for Professional Concrete Cutters Training Manual – Introduction to Diamond Blades, Bits, and Equipment Diamond Products’ Equipment Catalog ... -
Page 15: Service Parts
Service Filters/ Belts DP Part No. Description Manufacturer’s Part No. 2501211 Air Filter for Honda (GX630) (Donaldson #P821575) 2700348 Fuel Filter for Honda (GX630) (Honda #17672-880-000) 2702741 Oil Filter for Honda (GX630) (Honda #15400-PLM-AO1PE) 2503678 Blade Shaft Belt (3) for Honda (GX630) (Gates #3VX390) 2501969 Transmission Belt for Honda (GX630) -
Page 16: Warranty
(1) year from the date of shipment to Customer. The responsibility of Diamond Products under this Warranty is limited to replacement or repair of defective parts at Diamond Products’ Elyria, Ohio...
Need help?
Do you have a question about the CC190XL and is the answer not in the manual?
Questions and answers