Page 1 Avaya P550R/P580/ P880/P882 Multiservice ™ Switch ATM Uplink CLI Reference Guide Version 2.0 May 2002...
Page 2 Avaya disclaims responsibility for errors which may appear in this document, and it reserves the right, in its sole discretion and without notice, to make substitutions and modifications in the products and practices described in this document.
Page 3: Table Of Contents
... 1-13 set atm-link mapping... 1-14 set atm-link name... 1-15 set atm-link oam-loopback ... 1-16 show atm-link... 1-17 Global Commands ... 1-19 set network ... 1-20 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0...
Page 4 1-65 show pnni scope-table ... 1-66 show pnni summary-address-table ... 1-67 show pnni svccrcc-table... 1-68 Permanent Virtual Channel Commands ... 1-69 pvc ... 1-70 set pvc cdvt ... 1-71 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0...
Page 5 ... 1-113 help ... 1-114 nvram initialize ... 1-115 reload ... 1-116 reset... 1-117 show boot... 1-118 show file_name ... 1-119 show flash ... 1-120 show history... 1-121 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0...
Page 6 (enable | disable) ... 1-141 set vsport load-share... 1-142 set vsport name... 1-143 set vsport static-laft... 1-144 set vsport type... 1-145 show static-laft... 1-146 show vsport ... 1-147 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0...
Page 7: Overview Of The Contents
CLI commands associated with the ATM Uplink module. Technical Support To contact Avaya’s technical support: Conventions This section describes the conventions used in this document. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ® /P882 From the United States: 1-800-237-0016 Outside the United States: Contact your distributor.
Page 8: Text Conventions
Text Conventions This document uses the following text conventions: viii Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Convention Represents User Input User entered text. Boldface Text Menu command, keyword to be acted upon, or button name.
Page 9: Related Documentation
For more information about ATM, refer to the ATM Forum Web site: Avaya Products and Services For information about Avaya products and services, please consult the Avaya World Wide Web site at http://www.avaya.com. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference, Version 2.0 Online Documentation Documentation Feedback ATM Forum - http://atmforum.com ®...
Page 10 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0...
Page 11: Chapter 1 - Avaya Atm Uplink Module Cli Commands
Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Accessing/Exiting the Command Modes Command Syntax Conventions Basic Functions Accessing the ATM Uplink CLI P580R Supervisor Commands ATM Uplink Commands Table 1-1.
Page 12: Command Syntax Conventions
To exit the ATM Uplink Command Line Interface, enter quit. Note: Command Syntax Conventions Table 1-2 describes the command syntax conventions. Convention keyword <parameter> [optional] Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 From the User mode, enter enable. From the Privileged mode, enter configure.
Page 13: No Form Of Commands
The history buffer stores the last 20 commands you have entered. Use the key sequences in Table 1-3 to recall commands from the history buffer. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Description Required - one of the alternatives must be selected.
Page 14: Basic Functions
<Tab> command + command ? (Gives the next token (parameter or keyword)) Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-4. Basic Functions Description Example ATM# e? Lists the commands that begin with the Next possible...
Page 15: Accessing/Exiting The Atm Uplink Cli
Accessing/Exiting the ATM Uplink CLI To access the ATM Uplink CLI, you must first access the Avaya Multiservice Swith’s Supervisor console. There are two ways to access the Supervisor console: Using a Serial Interface to Access the Avaya Multiservice Switch’s Supervisor To access the CLI using a serial interface (such as HyperTerminal): Using Telnet to Access the Avaya Multiservice Switch’s Super-...
Page 16: Accessing The Atm Uplink Cli
* Note: The prompt reflects the change of mode. Exiting the ATM Uplink CLI To exit the ATM Uplink CLI: Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 address and user account for the switch. Default accounts are: •...
Page 17: Supervisor Commands
| app2 | boot Sample Output This example sets the boot image for the ATM module in slot 3 to app2. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 module. Table 1-6. Parameters, Keywords, Arguments Definition The slot number of the smart module being specified.
Page 18: Atm Uplink Commands
ATM-Link Commands Global Commands Interface Commands LEC Commands PNNI Commands Permanent Virtual Channel Commands QoS Domain Commands QoS Set Commands RED Pack Commands System Commands VPORT Commands VSPORT Commands Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0...
Page 19: Atm-Link Commands
Virtual Switch Port (VSP) has already been created. Once a VSP is created, you can use the ATM-Link commands to create and manage ATM Links within the VSP. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 atm-link set atm-link default-PVC...
Page 20: Atm-Link
The following example creates then deletes an ATM link named vsp1on the Virtual Switch Port whose ID is 4. 1-10 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 belong to must exist prior to creating the atm-link. Table 1-7. Arguments, Parameters, Keywords Definition Virtual switch port Identifier.
Page 21: Set Atm-Link Default-Pvc
Sample Output This example sets the default PVC for ATM Link “Link1” to the PVC whose ID is 1-0-300. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-8. Arguments, Parameters, Keywords Definition Virtual switch port Identifier. Range is 1 - 128.
Page 22: Set Atm-Link (Enable | Disable)
| disable Sample Output The following example enables ATM Link TestLink: 1-12 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-9. Arguments, Parameters, Keywords Definition The name of the ATM link you will enable or disable.
Page 23: Set Atm-Link Failover-Link
The following example clears the failover-link for ATM Link MainLink. Should MainLink fail, no backup is specified and traffic will not flow. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM Link. Links. Table 1-10. Arguments, Parameters, Keywords...
Page 24: Set Atm-Link Mapping
The following example maps Ethernet priority 6 to PVC 181 in the TestLink ATM Link. 1-14 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Any traffic forwarded at an un-mapped Ethernet priority will result in that traffic being dropped.
Page 25: Set Atm-Link Name
Sample Output This example changes the name of ATM Link TestLink to MainLink Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-12. Arguments, Parameters, Keywords Definition Name of the ATM Link (1 - 31 characters).
Page 26: Set Atm-Link Oam-Loopback
| disable Sample Output This example enables OAM Loopback on ATM Link AvayaLink. 1-16 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 VSPs. OAM is not supported with Routed VSPs. Table 1-13. Arguments, Parameters, Keywords Definition Name of the ATM Link.
Page 27: Show Atm-Link
Sample Output The following example shows the configuration information for Virtual Switched Port 2. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-14. Arguments, Parameters, Keywords Definition Virtual switch port identifier. Range is 1 - 128.
Page 28 1-18 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Outbound Priority 5 Outbound Priority 6 Outbound Priority 7 : 1-0-101 : 1-0-102 : 1-0-102...
Page 29: Global Commands
Global Commands Global commands configure the ATM Uplink module’s ATM address and Signalling type (such as PNNI or UNI). This section describes: Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 set network set network multiport set network pnni-level...
Page 30: Set Network
Sample Output This example disables, then enables the ATM network. 1-20 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 change to the configuration. After you make configuration changes, you must enable the network in order for the changes to take effect.
Page 31: Set Network Multiport
Sample Output This example sets network multiport support to yes, which enables PNNI. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 or the ATM Uplink 2.0 User Guide change to the configuration. After you make configuration changes, you must enable the network in order for the changes to take effect.
Page 32: Set Network Pnni-Level
Sample Output This example sets the PNNI level to 96. 1-22 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 “set network multiport” on page 21 change to the configuration. After you make configuration changes, you must enable the network in order for the changes to take effect.
Page 33: Set Network Prefix
Sample Output This example sets the ATM address prefix. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 change to the configuration. After you make configuration changes, you must enable the network in order for the changes to take effect.
Page 34: Show Network
Shows ATM network configuration for the ATM Uplink module. Syntax show network Sample Output This example shows the network configuration. 1-24 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM(configure)# show network ATM Network Configuration: ========================== Admin Status Operational Status...
Page 35: Interface Commands
Avaya ATM Uplink Module CLI Commands Interface Commands This section describes: set interface (enable | disable) set interface (medium-type) set interface (name) show interface 1-25 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0...
Page 36: Set Interface (Enable | Disable)
Sample Output This example shows interface 1 being disabled and enabled. 1-26 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 change to the configuration. After you make configuration changes, you must enable the interface in order for the interface to be operational.
Page 37: Set Interface (Medium-Type)
This example disables interface 1, sets the medium type to SONET and enables interface 1. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 change to the configuration. After you make configuration changes, you must enable the interface in order for the changes to take effect.
Page 38: Set Interface (Name)
Sample Output This example sets the name of ATM interface 1 to “thoreau”. 1-28 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 change to the configuration. After you make configuration changes, you must enable the interface in order for the changes to take effect.
Page 39: Show Interface
This example shows the configuration information for ATM interface 1. This example shows the configuration information for all configured interfaces. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-22. Parameters, Keywords, Arguments Definition The ATM interface identification number. The...
Page 40 1-30 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM Interface 2 Configuration: ============================== Interface Name : SonetPort2 Admin Status : Enabled Oper Status : Down Medium Type : Sonet Line Type : Multi-Mode Fiber Path Width...
Page 41: Lec Commands
(max-bus-cellrate-value) set lec (max-time) set lec (name) set lec (proxy) set lec (qos-domain) set lec (selector) set lec (server-addr) set lec (trigger-count) set lec (version) show lec 1-31 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0...
Page 42: Clear Lec Learp
Sample Output This example clears the LEARP table for LEC 1. 1-32 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-23. Parameters, Keywords, Arguments Definition optional parameter that identifies the LEC whose LEARP table you want to clear.
Page 43: Set Lec Agetime
<agetime-value> Sample Output This example sets the agetime for LEC 1 to be 2400 seconds. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-24. Parameters, Keywords, Arguments Definition ID # of the LEC whose Agetime value you want to change.
Page 44: Lec
This example creates then deletes a LEC named “adams” with an lecID of 90. 1-34 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-25. Parameters, Keywords, Arguments Definition The name you wish to assign to the LEC. The LEC name must be between 1 and 31 characters (alpha or numeric).
Page 45: Set Lec (Disable | Enable)
| enable Sample Output This example illustrates how to disable and enable LEC 2. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 the configuration. After you make configuration changes, you must enable the LEC in order for the changes to take effect.
Page 46: Set Lec (Join-Method)
Sample Output This example sets LEC 2 to join method LECS. 1-36 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 the configuration. After you make configuration changes, you must enable the LEC in order for the changes to take effect.
Page 47: Set Lec (Max-Bus-Cellrate-Value)
This example sets the maximum number of cells per second sent to the BUS for LEC 2 to 500cps. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 the configuration. After you make configuration changes, you must enable the LEC in order for the changes to take effect.
Page 48: Set Lec (Max-Count)
This example sets the maximum unknown frame count for LEC 2 to 15 for a programmed time interval. 1-38 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 the configuration. After you make configuration changes, you must enable the LEC in order for the changes to take effect.
Page 49: Set Lec (Max-Time)
This example sets the unknown frame time interval for LEC 2 to 45 seconds. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 the configuration. After you make configuration changes, you must enable the LEC in order for the changes to take effect.
Page 50: Set Lec (Name)
Sample Output This example sets the name of LEC 1 to “dawes.” 1-40 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 the configuration. After you make configuration changes, you must enable the LEC in order for the changes to take effect.
Page 51: Set Lec (Proxy)
Description Set the proxy mode for the LEC. The LEC can proxy for MAC addresses that are local to the Avaya switch only; or for MAC addresses learned from other LECs in addition to the local MAC address. If proxying for all, the ATM Uplink module will work in conjunction with another LEC to bridge between two ELANs.
Page 52: Set Lec (Qos-Domain)
Sample Output This example sets QOS Domain 1 for LEC 2. 1-42 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 the configuration. After you make configuration changes, you must enable the LEC in order for the changes to take effect.
Page 53: Set Lec (Selector)
Sample Output This example sets the ATM address selector for LEC 2 to 1F. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 the configuration. After you make configuration changes, you must enable the LEC in order for the changes to take effect.
Page 54: Set Lec (Server-Addr)
This example sets the server ATM address for LEC 2 to default. 1-44 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 the configuration. After you make configuration changes, you must enable the LEC in order for the changes to take effect.
Page 55: Set Lec (Trigger-Count)
This example sets the trigger count for LEC 2 to a programmed time interval of 15. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 the configuration. After you make configuration changes, you must enable the LEC in order for the changes to take effect.
Page 56: Set Lec (Version)
Sample Output This example sets LEC 2 to version V1. 1-46 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 the configuration. After you make configuration changes, you must enable the LEC in order for the changes to take effect.
Page 57: Show Lec
This example shows the configuration for all LECs. * Note: The actual output contains additional columns for VLAN This example shows the configuration for LEC 1. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-38. Parameters, Keywords, Arguments Definition Optional, the LEC identifier.
Page 58 1-48 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 LEC AMT Address Client Selector Server ATM Address : C5-0079-00000000000000000000- 00A03E000001-00 Join Method QOS Domain Maximum Unknown Frame Count (C10) : 10 Maximum Unknown Frame Time (C11) LE ARP Trigger Count...
Page 59: Show Lec (Learp)
Name lecID Sample Output This example shows the learp cache for LEC ID 2. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-39. Parameters, Keywords, Arguments Definition The LEC identifier. The range of values is: Minimum = 1, Maximum = 128.
Page 60: Pnni Commands
1-50 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0...
Page 61: Show Pnni Base-Table
Description Show PNNI base table. Syntax show pnni base-table Sample Output This example shows PNNI base table information. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM(configure)# show pnni base-table PNNI Base Table =============== pnniHighestVersion pnniLowestVersion pnniDtlCountOriginator...
Page 62: Show Pnni If-Table
Show PNNI Interface (IF) table. Syntax show pnni if-table Sample Output This example show PNNI IF table information. 1-52 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM(configure)# show pnni if-table PNNI Interface Table ==================== pnniIfNodeIndex pnniNodeIndex...
Page 63: Show Pnni Link-Table
Description Show PNNI link table Syntax show pnni link-table Sample Output This example shows PNNI link table information. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM-7(configure)# show pnni link-table PNNI Link Table ======================================= pnnideIndex pnniLinkPortId pnniLinkpnniDisplay...
Page 64: Show Pnni Map-Table
Show PNNI map table. Syntax show pnni map-table Sample Output This example shows PNNI map table information. 1-54 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM(configure)# show pnni map-table PNNI Map Table ========================================= pnnodeIndex pnniMapOriginatingNodeId 60a03911223344556677889911223302e03b0bd69000...
Page 65: Show Pnni Map-Addr-Table
Show PNNI map address table. Syntax show pnni map-addr-table Sample Output This example shows PNNI map address table information. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM # show pnni map-addr-table PNNI Map Node Table ============================================= pnniNodeIndex...
Page 66: Show Pnni Map-Node-Table
Show PNNI map node table. Syntax show pnni map-node-table Sample Output This example shows PNNI map node table information. 1-56 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM# show pnni map-node-table pnniNodeIndex pnniMapNodeId 60a03900000000000002e03b0b3da500201655667700 pnni MapNodePeerGroupId...
Page 67: Show Pnni Metrics-Table
Description Show PNNI metrics table. Syntax show pnni metrics-table Sample Output This example shows PNNI metrics table information. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM(configure)# show pnni metrics-table PNNI Metrix Table ================= pnniNodeIndex pnniMetricsTag pnniMetricsDirection...
Page 68: Show Pnni Nbr-Peer-Table
Show PNNI Neighbor (NBR) peer table Syntax show pnni nbr-peer-table Sample Output This example shows PNNI nbr peer table information. 1-58 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM(configure)# show pnni nbr-peer-table PNNI NBR Peer Table =================== pnniNodeIndex pnniNbrPeerRemoteNodeId...
Page 69: Show Pnni Nbr-Peer-Port-Table
Show PNNI NBR peer port table. Syntax show pnni peer-port-table Sample Output This example shows PNNI peer port table information. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM (configure)# show pnni nbr-peer-port- table PNNI NBR Peer Port Table ========================...
Page 70: Show Pnni Node-Table
Description Show PNNI node table. Syntax show pnni node-table Sample Output This example shows PNNI node table information. 1-60 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM# show pnni node-table pnniNodeIndex pnniNodeLevel pnniNodeId 60a03900000000000002e03b0b3da500201655667700 pnniNodeLowest pnniNodeAdminStatus...
Page 71: Show Pnni Node-Pgl-Table
Show PNNI node Peer Group Lead (PGL) table. Syntax show pnni node-pgl-table Sample Output This example shows PNNI node PGL table information. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM(configure)# show pnni node-pgl-table PNNI PGLE Table =============== pnniNodeIndex...
Page 72: Show Pnni Node-Svcc-Table
Show PNNI node Switch Virtual Channel Connection (SVCC) table. Syntax show pnni node-svcc-table Sample Output This example shows PNNI node SVCC table information. 1-62 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM(configure)# show pnni node-svcc-table PNNI Node SVCC Table ==================== pnniNodeIndex pnniNodeSvccInitTime...
Page 73: Show Pnni Node-Timer-Table
Show PNNI node timer table. Syntax show pnni node-timer-table Sample Output This example shows PNNI node timer table information. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM# show pnni node-timer-table PNNI Node Timer Table ===================== pnniNodeIndex...
Page 74: Show Pnni Ptse-Table
Show PNNI State Topology State Element (PTSE) table. Syntax show pnni ptse-table Sample Output This example shows PNNI PTSE table information. 1-64 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM(configure)# show pnni ptse-table PNNI PTSE Table =============== pnniNodeIndex pnniPtseOriginatingNodeId...
Page 75: Show Pnni Route-Addr-Table
Show PNNI route address table. Syntax show pnni route-addr-table Sample Output This example shows PNNI route address table information. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM(configure)# show pnni route-addr-table PNNI Route Address Table ======================== pnniNodeIndex...
Page 76: Show Pnni Scope-Table
Description Show PNNI scope table. show pnni scope-table Sample Output This example shows PNNI scope table information. 1-66 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM(configure)# show pnni scope-table PNNI Scope Mapping Table ======================== pnniNodeIndex pnniScopeLocalNetwork...
Page 77: Show Pnni Summary-Address-Table
Show PNNI summary address table. Syntax show pnni summary-address-table Sample Output This example shows PNNI summary address table information. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM(configure)# show pnni summary-address- table PNNI Summary Address Table ==========================...
Page 78: Show Pnni Svccrcc-Table
Syntax show pnni summary-address-table Sample Output This example shows PNNI summary SVC CRC table information. 1-68 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM(configure)# show pnni summary-address- table PNNI Summary Address Table ===================================== pnni Node Index...
Page 79: Permanent Virtual Channel Commands
1-69 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0...
Page 80: Pvc
4 and a vci of 101. The following example removes the pvc created in the previous example. 1-70 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 class command to change the traffic class if desired. Table 1-40. Arguments, Parameters, Keywords Definition The name being assigned to the pvc.
Page 81: Set Pvc Cdvt
- value Sample Output The following example sets the cdvt to 5. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-41. Arguments, Parameters, Keywords Definition The identifier of the pvc. This is equal to <physPort>...
Page 82: Set Pvc Mbs
Sample Output The following example sets the maximum burst size to 10000. 1-72 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-42. Arguments, Parameters, Keywords Definition The identifier for the pvc. It is equal to <physPort>...
Page 83: Set Pvc Pcr
Sample Output The following example sets the peak cell rate to 10000. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-43. Arguments, Parameters, Keywords Definition The identifier for the pvc. It is equal to <physPort>...
Page 84: Set Pvc Port
Sample Output The following example attaches the pvc to physical port 1 1-74 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-44. Arguments, Parameters, Keywords Definition The identifier for the pvc. It is equal to <physPort>...
Page 85: Set Pvc Priority
Command Mode Configure Description Sets the inbound priority for the specified pvc. Traffic received on this PVC will be forwarded through the Avaya switch at this priority level. Syntax set pvc <pvcID> priority <priority> Name pvcID priority...
Page 86: Set Pvc Red-Pack
Sample Output The following example sets the red-id of the pvc to 3. 1-76 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 class PVCs. Table 1-46. Arguments, Parameters, Keywords Definition The identifier for the pvc. It is equal to <physPort>...
Page 87: Set Pvc Scr
Sample Output The following example sets the sustained cell rate of the pvc to 10000. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 than the Peak Cell Rate setting. Table 1-47. Arguments, Parameters, Keywords Definition The identifier for the pvc. It is equal to <physPort>...
Page 88: Set Pvc Traffic-Class
Sample Output The following example assigns a traffic-class of “CBR” to the pvc. 1-78 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-48. Arguments, Parameters, Keywords Definition The identifier for the pvc. It is equal to <physPort>...
Page 89: Set Pvc Vci
Sample Output The following example changes the vci for the pvc from 101 to 201. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-49. Arguments, Parameters, Keywords Definition The identifier for the pvc. It is equal to <physPort>...
Page 90: Set Pvc Vpi
Sample Output The following example sets the vpi for the pvc from 4 to 0. 1-80 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-50. Arguments, Parameters, Keywords Definition The identifier for the pvc. It is equal to <physPort>...
Page 91: Show Pvc
Sample Output The following example displays the PVCs in Link1 and then detailed information for pvc 1-4-101 in Link1: Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-51. Arguments, Parameters, Keywords Definition The name of the link whose PVC’s you want to view.
Page 92: Qos Domain Commands
Chapter 1 QoS Domain Commands This section describes: qos-domain no qos-domain set qos-domain (mapping) set qos-domain (name) set qos-domain (name) show qos-domain 1-82 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0...
Page 93: Qos-Domain
Name qosDomainID Sample Output This example creates then deletes a QoS domain with ID 3. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-52. Parameters, Keywords, Arguments Definition The QoS domain ID number. The range of values is: Minimum = 1, Maximum = 128.
Page 94: Set Qos-Domain (Mapping)
6. Any traffic with Ethernet priority 6 will be forwarded down a PVC with the traffic class and parameters of QoS Set 24. 1-84 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-53. Parameters, Keywords, Arguments Definition The QoS Domain ID number.
Page 95: Set Qos-Domain (Name)
Sample Output This example sets the name for QoS domain 1 to “thoreau”. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-54. Parameters, Keywords, Arguments Definition The QoS domain ID number. The range of values is: Minimum = 1, Maximum = 128.
Page 96: Show Qos-Domain
Sample Output This example shows QoS domain configuration information for qos-domain 1. 1-86 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-55. Parameters, Keywords, Arguments Definition The QoS domain ID number. The range of values is: Minimum = 1, Maximum = 128.
Page 97 This example shows qos-domain configuration information for all existing qos-domains. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM(configure)# show qos-domain Name ---- thoreau QosDomain3 QosDomain12 1-87...
Page 98: Qos Set Commands
(mbs) set qos-set (mbs) set qos-set (mbs) set qos-set (mbs) set qos-set (pcr) set qos-set (priority) set qos-set (priority) set qos-set (scr) set qos-set (traffic-class) show qos-set 1-88 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0...
Page 99: Qos-Set
Sample Output This example creates then deletes QoS set 24 in QoS Domain ID 12. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-56. Parameters, Keywords, Arguments Definition The QoS domain ID number. The range of values is: Minimum = 1, Maximum = 128.
Page 100: Set Qos-Set (Mbs)
This example sets the maximum burst size for QoS set 24 in QoS Domain 12 to a value of 2000 cps. 1-90 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-57. Parameters, Keywords, Arguments Definition The QoS domain ID number. The range of values is: Minimum = 1, Maximum = 128.
Page 101: Set Qos-Set (Name)
Sample Output This example sets the name of QoS set 24 in QoS Domain 12 to IPPhoneTraffic Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-58. Parameters, Keywords, Arguments Definition The QoS domain ID number. The range of values is: Minimum = 1, Maximum = 128.
Page 102: Set Qos-Set (Pcr)
This example sets the peak cell rate for QoS set 24 in QoS Domain 12 to a value of 2500 cps. 1-92 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-59. Parameters, Keywords, Arguments Definition The QoS domain ID number. The range of values is: Minimum = 1, Maximum = 128.
Page 103: Set Qos-Set (Priority)
Sample Output This example sets the inbound priority for QoS set 24 in QoS Domain 12 to Ethernet priority 6. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-60. Parameters, Keywords, Arguments Definition The QoS domain ID number. The range of values is: Minimum = 1, Maximum = 128.
Page 104: Set Qos-Set (Red-Pack)
Sample Output This example assigns RED Pack 3 to QoS Set 24 in QoS Domain 12. 1-94 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-61. Parameters, Keywords, Arguments Definition The QoS domain ID number. The range of values is: Minimum = 1, Maximum = 128.
Page 105: Set Qos-Set (Scr)
Sample Output This example sets the sustained cell rate value for QoS set 24 in QoS Domain 12 to a value of 1800 cps. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-62. Parameters, Keywords, Arguments Definition The QoS domain ID number.
Page 106: Set Qos-Set (Traffic-Class)
This example sets the traffic class for QoS Set 24 in QoS Domain 12 to ubr. 1-96 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-63. Parameters, Keywords, Arguments Definition The QoS domain ID number. The range of values is: Minimum = 1, Maximum = 128.
Page 107: Show Qos-Set
Sample Output This example shows the configuration for QoS set 24 in QoS Domain 12. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-64. Parameters, Keywords, Arguments Definition The QoS domain ID number. The range of values is: Minimum = 1, Maximum = 128.
Page 108: Red Pack Commands
Chapter 1 RED Pack Commands This section describes: set random-detect (max-threshold) set random-detect (min-threshold) set random-detect (probability) set random-detect (thmin-thmax-prob-wq) set random-detect wq show random-detect 1-98 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0...
Page 109: Set Random-Detect (Max-Threshold)
Sample Output This example sets the maximum threshold for RED Pack 3 to 255. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 commands, see Configuring RED Pack Parameters in Chapter 2 of the Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink User Guide.
Page 110: Set Random-Detect (Min-Threshold)
Sample Output This example sets the minimum threshold for RED Pack 3 to 24. 1-100 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-66. Parameters, Keywords, Arguments Definition The value identifying the particular RED Pack.
Page 111: Set Random-Detect (Probability)
Sample Output This example sets the probability factor for RED Pack 3 to -7. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-67. Parameters, Keywords, Arguments Definition The value identifying the particular RED Pack.
Page 112: Set Random-Detect (Thmin-Thmax-Prob-Wq)
Sample Output This example sets all the parameters for RED Pack 3. 1-102 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-68. Parameters, Keywords, Arguments Definition The value identifying the particular RED Pack. The minimum threshold value for the RED Pack.
Page 113: Set Random-Detect Wq
Sample Output This example sets the weight of the queue for RED Pack 3 to -8. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-69. Parameters, Keywords, Arguments Definition The value identifying the particular RED Pack.
Page 114: Show Random-Detect
This example displays all the parameters for all configured RED Packs then the parameters for RED Pack 3 only: 1-104 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-70. Parameters, Keywords, Arguments Definition Optionally, the value identifying the particular RED Pack.
Page 115: System Commands
System Commands This section describes: Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 copy (filename) copy (startup-config) copy running-config startup-config erase erase startup-config exit help nvram initialize nvram initialize reload reset show boot show file_name show flash...
Page 116: Copy (Filename)
Sample Output This example copies the file named running-config.txt, to the file named text.txt. 1-106 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-71. Parameters, Keywords, Arguments Definition The names of the source file and destination file in NVRAM.
Page 117: Copy (Startup-Config)
Sample Output This example copies the file test.txt to the startup configuration. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 running configuration to startup. In this case, you would answer no to the prompt. To answer yes would overwrite the configuration you actually want to boot with.
Page 118: Copy Running-Config Startup-Config
Syntax copy running-config startup-config Sample Output This example copies the running configuration to the startup configuration. 1-108 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM-3(configure)# copy running-config startup-config Wrote running-config to '/nvram/startup.txt' ATM-3(configure)#...
Page 119: Dir
Name filename Sample Output This example shows the files listed in NVRAM. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-73. Parameters, Keywords, Arguments Definition The name of the file in NVRAM. It must have a 1-8 letter base filename, and a three letter file extension.
Page 120: End
Exit the configuration mode and re-enter the privileged mode. This is the same as the Exit command. Syntax Sample Output This example illustrates how to exit the configuration mode and re-enter the privileged mode. 1-110 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM(configure)end ATM#...
Page 121: Erase
Name filename Sample Output This example erases the file named test.txt. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-74. Parameters, Keywords, Arguments Definition The name of the file in NVRAM. It must have a 1-8 letter base filename, and a three letter file extension.
Page 122: Erase Startup-Config
This example shows the help form of the erase startup-config command. 1-112 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 the running-config to startup-config afterward. If no config is copied back to startup-config, the ATM Uplink module will boot with the default factory configuration.
Page 123: Exit
Exit the current mode and re-enter the previous mode. Syntax exit Sample Output This example illustrates exiting the current mode and re-entering the previous mode. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM(configure)# exit ATM# exit ATM> 1-113...
Page 124: Help
Sample Output This example displays the help list of commands available in the User mode. 1-114 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM> help dir [<filename>] Display the list of files in NVRAM, or a...
Page 125: Nvram Initialize
Syntax nvram initialize Example This example would initialize the ATM Uplink module back to factory default configuration. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM(configure)# nvram initialize NV is initialized ... reboot to take effect. 1-115...
Page 126: Reload
Once the module has rebooted, you will have to re- establish a session to it. 1-116 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM(configure)# reload Log entry 184 by event 2 at 00-May_23 19:50:27 : Alarm(60) Description: Module reset detected : Module 6.[Module 6]...
Page 127: Reset
Once the module has rebooted, you will have to re-establish a session to it. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM(configure)# reset Log entry 184 by event 2 at 00-May_23 19:50:27...
Page 128: Show Boot
Syntax show boot Sample Output This example displays FEPROM information. 1-118 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM (configure)# show boot Checking for valid image in BOOT. File Information: File Format Type = Binary Target Location = Boot...
Page 129: Show File_Name
Name filename Sample Output This example shows the contents of file ‘/nvram/startup.txt’. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-75. Parameters, Keywords, Arguments Definition The name of the file in NVRAM. It must have a 1-8 letter base filename, and a three letter file extension.
Page 130: Show Flash
Syntax show flash Sample Output This example shows FEPROM information. 1-120 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM> show flash Checking for valid image in BOOT. File Information: File Format Type = Binary Target Location = Boot...
Page 131: Show History
Syntax show history Sample Output This example shows the last several commands entered during a session. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM-9(configure)# show history conf show lec show atm 008 show link 10...
Page 132: Show Running-Config
Syntax show running-config Sample Output This example shows the running configuration. 1-122 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM> show running-config Current configuration: ! ATM Uplink Agent v2.0.0 M8002-AOC12MMF Module set random-detect 1 max-threshold 120...
Page 133: Show Startup-Config
List the commands that represent the startup configuration. Syntax show startup-config Sample Output This example shows the startup configuration. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM (configure)# show startup-config Contents of file '/nvram/startup.txt': ! ATM Uplink Agent v2.0.0 M8002-AOC12MMF Module...
Page 134: Show Version
Display the software version currently running on the system. Syntax show version Sample Output This example shows the version of software that is currently running. 1-124 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 ATM(configure)# show version ATM Uplink Agent v2.0.0...
Page 135: Vport Commands
(enable | disable) set vport (ilmi) set vport (max-vci) set vport (name) set vport (path-cost) set vport (sig-type) set vport (traffic-shape-rate) show vport 1-125 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0...
Page 136: Vport
This example creates a VPORT on physical port 1 for VP 5. 1-126 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Shape Rate (CPS) and Max VCI on the other VPORT(s) to free up bandwidth for the new VPORT.
Page 137: Set Vport (Enable | Disable)
| disable Sample Output This example enables VPORT 1 0. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-77. Parameters, Keywords, Arguments Definition The ATM interface number. The range of values is: Minimum = 1, Maximum = 2.
Page 138: Set Vport (Ilmi)
This example sets the ILMI version for VPORT 1 5 to 4.0 Address Registration. 1-128 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 to the configuration. After you make configuration changes, you must enable the VPORT in order for the changes to take effect.
Page 139: Set Vport (Max-Vci)
Sample Output This example sets the maximum VCI for VPORT 1 5 to 22000. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 to the configuration. After you make configuration changes, you must enable the VPORT in order for the changes to take effect.
Page 140: Set Vport (Name)
This example sets the name of VPORT 1 5 to “dawes.” 1-130 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 to the configuration. After you make configuration changes, you must enable the VPORT in order for the changes to take effect.
Page 141: Set Vport (Path-Cost)
Sample Output This example sets the path cost for VPORT 1 5 to 15000000. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 to the configuration. After you make configuration changes, you must enable the VPORT in order for the changes to take effect.
Page 142: Set Vport (Sig-Type)
This example sets the signature type for VPORT 1 5 to auto. 1-132 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 to the configuration. After you make configuration changes, you must enable the VPORT in order for the changes to take effect.
Page 143: Set Vport (Traffic-Shape-Rate)
Sample Output This example sets the output throttling on VPORT 1 5 to 0. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 to the configuration. After you make configuration changes, you must enable the VPORT in order for the changes to take effect.
Page 144: Show Vport
Sample Output This example shows configuration information for VPORT 1 5. 1-134 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 include. You cannot enter one without the other. If omitted, all Virtual Ports will be displayed with summarized information Table 1-84.
Page 145 This example shows configuration information for all existing VPORTs. ATM(configure)# show vport Phys Port ---- Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 VPort Admin Oper Name Status Status ------- ------ ------ VPort1 Enabled Dormant dawes Enabled Dormant...
Page 146: Vsport Commands
This section describes the following commands: vsport no vsport set vsport default-link set vsport default-port set vsport (enable | disable) set vsport load-share set vsport name set vsport static-laft show static-laft 1-136 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0...
Page 147: Vsport
Switched Port named TestVSP with VSP ID 10. ATM(configure)# vsport TestVSP packet-rep yes 10 ATM(configure)# no vsport 10 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-85. Arguments, Parameters, Keywords Definition The name of the VSP. (1 to 32 characters) (Optional) Identifies the port as replicating, when combined with the “yes”...
Page 148: Set Vsport Default-Link
Sample Output The following example sets the Default Link for VSP 4 to ATM Link Link1. 1-138 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-86. Arguments, Parameters, Keywords Definition Virtual Switched Port Identifier. Possible values range from 1 - 128.
Page 149: Set Vsport Default-Port
Sample Output The following example sets the Default Link for VSP 4 to ATM Link Link1. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-87. Arguments, Parameters, Keywords Definition Virtual Switched Port Identifier. Possible values range from 1 - 128.
Page 150: Set Vsport Default-Pvc
The following example sets the Default PVC for VSP 4 to Physical Port 1, VP 7, VC 100. 1-140 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-88. Arguments, Parameters, Keywords Definition Virtual Switched Port Identifier. Possible values range from 1 - 128.
Page 151: Set Vsport (Enable | Disable)
Sample Output The following is an example of a Virtual Switched Port with VSP ID 4, being enabled. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-89. Arguments, Parameters, Keywords Definition Virtual Switched Port Identifier. Possible values range from 1 - 128.
Page 152: Set Vsport Load-Share
Sample Output The following example enables VSP 4 for load sharing. 1-142 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-90. Arguments, Parameters, Keywords Definition Virtual Switched Port Identifier. Possible values range from 1 - 128.
Page 153: Set Vsport Name
The following example assigns the name EngVSP to VSP ID 4: ATM(Configure)# set vsport 4 name EngVSP Name EngVSP has been set for VSPort 4 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-91. Arguments, Parameters, Keywords Definition Virtual Switched Port Identifier.
Page 154: Set Vsport Static-Laft
Entry MAC[00:11:22:33:44:55] VLAN[0] successfully added ATM(Configure)# no static-laft 12 00:11:22:33:44:55 Entry MAC[00:11:22:33:44:55] VLAN[0] successfully deleted 1-144 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-92. Arguments, Parameters, Keywords Definition Virtual Switched Port Identifier. Possible values range from 1 - 128.
Page 155: Set Vsport Type
Sample Output The following example sets VSP ID 4 to “simple-bridge”. Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-93. Arguments, Parameters, Keywords Definition Virtual Switched Port Identifier. Possible values range from 1 - 128.
Page 156: Show Static-Laft
The following exampled shows the static LAFT entries for VSP ID 5. ATM-7> show static-laft 5 ========================================= 1-146 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-94. Arguments, Parameters, Keywords Definition Virtual Switched Port Identifier. Possible values range from 1 - 128.
Page 157: Show Vsport
Default ATM Link Default PVC [Port 1] Default PVC [Port 2] Load Share Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Table 1-95. Arguments, Parameters, Keywords Definition (Optional) Virtual Switched Port Identifier. Possible values range from 1 - 128.
Page 158 Chapter 1 1-148 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0...
Page 159 1-32 legacy-cli 1-115 nvram initialize 1-115 qos-domain 1-83 qos-set 1-89 qos-set (cdvt) 1-90 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 qos-set (clr) 1-90 qos-set (max-ctd) 1-90 qos-set (mbs) 1-90 qos-set (pcr) 1-92 qos-set (peak-cdv) 1-93 qos-set (priority) 1-93...
Page 160 1-112 erase startup-config command 1-112 exit command 1-113 exiting command modes 1-1 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 Global commands set interface (medium-type) 1-27 set interface (name) 1-28 set network 1-20 set network multiport 1-21...
Page 161 1-117 serial interface using 1-5 set buffering fabric-port (hipri-service-ratio) 1-25 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 set interface (medium-type) command 1-27 set interface (name) command 1-28 1-58 set interface command 1-26 set lec (join-method) command 1-36...
Page 162 1-120 show running-config 1-122 show startup-config 1-123 show version 1-124 shwo history 1-121 Avaya P550R/P580/P880/P882 Multiservice Switch ATM Uplink CLI Reference Guide, Version 2.0 technical support 1-vii text conventions documentation 1-viii Avaya 1-ix using the serial interface 1-5...

This manual is also suitable for:

P580 P880 P882

Avaya Cajun P550R Cli Reference Manual

Quick Links

Related Manuals for Avaya Cajun P550R

Summary of Contents for Avaya Cajun P550R