Subscribe to Our Youtube Channel
Related Manuals for Microsens MS453514M
Summary of Contents for Microsens MS453514M
- Page 1 Gigabit Ethernet Switch Quick Installation Guide MS400834M Version 1.0 ©2017_MICROSENS GmbH & Co. KG_Küferstr. 16_59067 Hamm/Germany_www.microsens.com...
-
Page 2: Table Of Contents
Connecting the AC Power Cord ............5 Installing SFP Modules ..............6 3. Initial Configuration of Switch ............... 7 Initial Switch Configuration Using Web Browsers ......... 7 Initial Switch Configuration Procedure ..........7 4. Troubleshooting ..................... 9 ©2017_MICROSENS GmbH & Co. KG_Küferstr. 16_59067 Hamm/Germany_www.microsens.com... -
Page 3: Introduction
Page 1 of 9 _______________________________________________________________________________________________ Introduction 1.1 Overview This user guide describes how to install, configure, and troubleshoot the MS453514M, 28 Port managed Gigabit Ethernet (GBE) PoE(+) Switch. By reading this user guide, users can perform the following tasks: ... - Page 4 100Mbps. The port has no active network cable connected, or it is not established a link to connected device. Otherwise, the port may have been disabled through the switch user interface. ©2017_MICROSENS GmbH & Co. KG_Küferstr. 16_59067 Hamm/Germany_www.microsens.com...
-
Page 5: Mode / Reset Button
Reset the switch 2 ~ 7 seconds Blinking green ALL LEDs light OFF Restore to defaults 7 ~ 12 seconds Blinking green ALL LEDs stay ON Table 4: Mode / Reset Button Descriptions ©2017_MICROSENS GmbH & Co. KG_Küferstr. 16_59067 Hamm/Germany_www.microsens.com... -
Page 6: Installing The Switch
Place the switch on a rack shelf in the rack. Push it in until the oval holes in the brackets align with the mounting holes in the rack posts. Step 3: Attach the brackets to the posts. Insert screws and tighten them. Figure 4: Attaching Brackets to the Rack Post ©2017_MICROSENS GmbH & Co. KG_Küferstr. 16_59067 Hamm/Germany_www.microsens.com... -
Page 7: Mounting The Switch On Desk Or Shelf
Connect the other end of the AC power cord to the AC power outlet. Step 3: Check the SYS LED. If it is ON, the power connection is correct. Figure 6: Connecting AC Power Cord ©2017_MICROSENS GmbH & Co. KG_Küferstr. 16_59067 Hamm/Germany_www.microsens.com... -
Page 8: Installing Sfp Modules
never look straight into the output of fiber optic components – danger of blinding! cover all unused optical connections with caps. commission the transmission link only after completing all connections. ©2017_MICROSENS GmbH & Co. KG_Küferstr. 16_59067 Hamm/Germany_www.microsens.com... -
Page 9: Initial Configuration Of Switch
PC (e.g. any IP address not in use, and in between 192.168.1.2 and 192.168.1.254), Subnet mask (e.g. 255.255.255.0), and Default gateway that corresponds with your network setup. Then enter your preferred and Alternate DNS server addresses. ©2017_MICROSENS GmbH & Co. KG_Küferstr. 16_59067 Hamm/Germany_www.microsens.com... - Page 10 - Clean browser cookies and temporary internet files. - Check your PC settings again and repeat step 2. Enter the factory default username and password in login page. Click “Login” to log into the switch. ©2017_MICROSENS GmbH & Co. KG_Küferstr. 16_59067 Hamm/Germany_www.microsens.com...
-
Page 11: Troubleshooting
Table 5: Troubleshooting Table This document in whole or in part may not be duplicated, reproduced, stored or retransmitted without prior written permission of MICROSENS GmbH & Co. KG. All information in this documents is preliminary and provided ‘as is’ and subject to change without notice. MICROSENS GmbH & Co. KG disclaims any liability for the correctness, completeness or quality of the information provided, fitness for a particular purpose or consecutive damage.
Need help?
Do you have a question about the MS453514M and is the answer not in the manual?
Questions and answers