Ko Propo BS 2 Series Manual

BSx2 Series servo
About safety
Note on usage
•We have examined the operation of this BSx2 servo in combination with
other KO PROPO products as a prerequisite condition. We cannot
assume any responsibility for the use of other company' s products with
this unit.
•Vibration during usage can damage the servo. Use the rubber grommets
included to prevent the servo from coming in contact with mechanical
plates. Over tightening the grommets reduces the effect of preventing
vibration.
•Check any linkage connected to the servo for free movement. Loose or
bound linkage will increase power consumption, which may shorten the
operational life of the servo.
•When using dry cells as a power supply, the correct performance may
not be shown.
• M odif ic ation of the unit by the customer may render the product
un-repairable.
* S p e c i f i c at i o ns may c hang e w it h o ut n ot i c e due to p e r fo r m anc e
improvements.
Features
ICS (interactive communication system) allows for the settings
to be read, changed and transmitted between the servo.In
addition, the possibility to interact with the communication by
changing and programming has extended the ICS purpose.
BSx2 ICS USB Adapter HS
Please download software for setting from our site.
※30200 :BSx Standard can not ICS setting.
When the servo powers on there may seem to be a slight
glitch, this is normal.
BSx2 Digital servos have high torque in the neutral position.
Sometimes you may see this slight glitch at neutral but this is
nor mal. Please use this ser vo as this does not alter the
performance.
Contact information for repairing goods
Requesting repair service
Please write the following items in as much detail as possible and
send it with the repair goods.
(1) Situation of the trouble.
(2) Equipment used. (type of transmitter, receiver, servo, and esc)
(3) Vehicle name and installing situation when being installed.
(4) The type and the number of items that have been sent.
(5) Return address, name, and telephone number
manual
Danger
T h e f o l l o w i n g
displays the content
o f d a n g e r t h a t c a n
cause serious injury,
death and etc.
Attention
This display shows
the content to which
a possibility and/or a
d i s a d v a n t a g e o u s
accident may occur
causing injury.
Set content
Pulse Stretch
Computer(Windows)
Model Select
KONDO KAGAKU CO.,LTD
Service department
TEL : 03-3807-7648
Hours of operation:9:00-12:00 & 13:00-17:00 M-F except national holidays Saturday
and Sunday closed
ADDRESS : 4-17-7 Higashi-Nippori, Arakawa-ku Tokyo Japan 116-0014 Japan
Latest information can be accessed here. >> http://www.kopropo.co.jp
Thank you for purchasing the BSx2 servo. Please refer often to this
manual before using the product. Also please keep this manual for
future references and refer to it at anytime.
While operating this product, do not carelessly touch, put it to your face or
etc. *There is danger of fracturing or cutting your finger or other parts of
your body from the strong torque output of the output axis. There is also the
d a n g e r o f b e i n g b u r n e d d u e t o t h e h e a t g e n e r a te d i f t h e s e r vo i s
over-loaded.
•The connection of a BSx2 servo should only be used with our company' s
p r o d u c t s f o r t h e b e s t r e s u l t . O u r c o m p a ny d o e s n o t a s s u m e t h e
responsibility of damage, etc. that may occur because of the use of this
product in combination with other manufacture' s products.
•Confirm the connector direction and make sure it is securely inserted. If
the connector becomes loose due to vibration during a run, it will drive
recklessly.
•Do not use in a place where there are puddles or rain. *Water may enter
the equipment and cause damage internally.
•Resolve any problems before proceeding and do not remodel the product.
The holding characteristic of a digital servo
can be set similar to that of an analog servo.
Stretch 1
Around neutral
Range of
Stretch 1
( 0~255 / Max. 255 )
A function to adjust the maximum power of the servo
Speed
( 0~127 / Max. 127 )
A function to improve the initial response of the servo.
Punch
( 0~10 / Max. 10 )
Adjusting the dead band. Narrowing the dead band creates a more
Dead Band precise neutral position, but the ser vo may make more noise
according to how your linkage is set.
( 0~5 )
A function to adjust brake feeling of the servo
Dumping
( 0~255 )
5 model memories
( 1~5 )
(service)
Stretch 2
Around end point of steering range
Range of
Stretch 2
( 0~255 / Min. 0,255 )